• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.497-504
• /
• 2005

This paper presents the results of experimental studies on the equipment isolation effect considering the floor response. For this purpose, shaking table tests were performed. For the measuring the floor response, numerical analysis was performed. For the isolation for the equipment, Natural Rubber Bearing(NRB), High Damping Rubber Bearing(HDRB) and Friction Pendulum System(FPS) were used. Finally, it is presented that the isolation systems used in this test can be adopted for the small equipment isolation. But the rubber bearing used in this study affected to the temperature change very sensitively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1246-1251
• /
• 2000

High level random vibration environments induced while launching of spacecraft can damage sensitive electronic equipment very rapidly, unless the equipment is properly packaged. Thus very careful consideration on the launch environment, especially for high level random vibration, is required in the design stage of electronic equipment of spacecraft. This paper describes the development process of Solar Array Regulator for KOMPAT-2, which is designed and tested by Korean engineers. Both analytical and experimental techniques are introduced in this paper.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.274-277
• /
• 2001

This paper describes the simulation study. conducted on the propagation characteristics of AE signal. In the case of gas insulation, such as $SF_6$, the equipment is less affected by the environment condition than air insulation, because the component parts of equipment were placed in the enclosure, which is filled with compressed gas. But. when the breakdown in the electric insulation occurs. it takes much time and economical efforts to repair. Therefore it is very important to diagnose the equipment before the accident. And. in general. UHF and AE signal is the most common transducer to diagnose the state of the power equipment, so, in this investigation, we make a experimental apparatus with aluminum plate and transient analysis with ANSYS to observe the propagation characteristics of AE signal. Through the result of the analysis. we can make a further understanding on the propagation characteristics of AE signal, and get the fundamental skills for the GIS diagnosis.

• 한국정밀공학회지
• /
• 제24권6호
• /
• pp.72-77
• /
• 2007

A safety-related equipment for the nuclear power plant should be needed an equipment qualification. In this paper, the approach, methods, philosophies, and procedures for qualifying the large squirrel-cage induction electric pump motors for use in ULCHIN 5, 6 Nuclear Power Plants were presented. The method of qualification is a combination of experimental test and analytic method, which is composed of radiation exposure test, seismic simulation test, thermal aging analysis for non-metallic materials, and seismic analysis. The results showed that the motor performed its safety function with no failure mechanism under postulated service conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.274-277
• /
• 2001

This paper describes the simulation study, conducted on the propagation characteristics of AE signal. In the case of gas insulation, such as SF6, the equipment is less affected by the environment condition than air insulation, because the component parts of equipment were placed in the enclosure, which is filled with compressed gas. But, when the breakdown in the electric insulation occurs, it takes much time and economical efforts to repair. Therefore it is very important to diagnose the equipment before the accident. And, in general, UHF and AE signal is the most common transducer to diagnose the state of the power equipment, so, in this investigation, we make a experimental apparatus with aluminum plate and transient analysis with ANSYS to observe the propagation characteristics of AE signal. Through the result of the analysis, we can make a further understanding on the propagation characteristics of AE signal, and get the fundamental skills for the GIS diagnosis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.227-236
• /
• 1997

Construction equipment noise has caused much annoyance for a number of dwellers in nearby construction field and has become a very serious issue in our living environment. Therefore, in our country, a practical solution and a better method of reducing construction equipment noise are highly required in construction field. Practical solutions for the construction equipment noise, however, are very difficult because the poorness of basic data and insufficiency of the existing research. Especially, in order to establishment of sound insulation plan about pilings work noise that has highly sound pressure level and impactive, a real situation of sound characteristics about pilings work noise in foundation work demands close investigation. In this point, this study attempts to surveys the characteristics of attenuation and propagation of construction equipment noise in pilings work using SIP(soilcement injected precast pile) method. And this study intends to get the basic data for establishment of a standard about construction noise.

• 드라이브 ㆍ 컨트롤
• /
• 제19권4호
• /
• pp.70-76
• /
• 2022

In this paper, we develops an unmanned test system for the purpose of realizing an actual forklift-based test-bed for the operation durability of the forklift mast. First, two robot actuators were applied to the lever to replace lever manipulation of the operator. For detecting the height of the fork and the tilt angle of the mast, the laser displacement sensor and the inclinometer were installed to the forklift. Next, the embedded control system was used to control the robot actuator with reference to test mode. Experimental evaluation verified that developed test system was effective and practical for the viewpoint of the repeatability of the test mode.

• 반도체디스플레이기술학회지
• /
• 제20권1호
• /
• pp.25-31
• /
• 2021

The semiconductor and display equipment demands an ultra-fine precision of several nm to several ㎛, and the scale is getting smaller due to the explosive development. The manufacturing process equipment for such products with ultra-fine precision is very sensitive to ultra-small vibrations flowing from the floor, resulting in problems of production defects and yield degradation. The vibration criteria are a standard that regulates the vibration environment of the floor where such precision process equipment will be installed. The BBN vibration criteria defined the allowable vibration velocity level in the frequency domain with a flat and inclined line and presented a rating according to it. However, the actual vibration criteria have appeared with various magnitudes in the frequency domain according to the dynamic characteristics of individual equipment. In this study, the relationship between the relative motion of two major points in the equipment and the vibration magnitude of the floor is presented using the frequency response function of a simple 3-DOF model. It is describing the magnitudes according to the frequency of the floor vibration that guarantees the allowable relative motion and this can be used as the vibration criteria. In order to obtain the vibration criteria experimentally a method of extracting through a modal test was introduced and verified analytically. It provides vulnerable frequency and magnitude to floor vibration in consideration of the dynamic characteristics of individual equipment. And it is possible to know necessary to improve the dynamic characteristics of the equipment, and it can be used to check the vibration compatibility of the place where the equipment will be installed.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권2호
• /
• pp.141-148
• /
• 2015

본 연구에서는 진공 차단기(Vacuum circuit breaker)의 동적 특성을 모사하기 위해 리커다인을 이용한 다물체 동역학 해석 모델이 개발 되었다. 진공 차단기는 VI(Vacuum interrupter)를 포함한 3 개의 주회로 부와, 구동 메커니즘을 포함한 기구부로 구성된다. 이 해석적 모델의 검증을 위해, 해석 결과와 실측을 통한 실험적 결과를 비교 하였다. 일반적으로, 원활한 사고 전류 차단을 위해서는 0.9~1.1m/s 의 차단속도(Opening velocity)가 필요하다. 차단 속도의 향상을 위해, 다구찌 기법을 이용하여 진공 차단기의 설계 변수 최적화를 수행하였다. 또한 향상된 차단기의 동적 특성을 검증하기 위해, 해석 결과와 개선된 샘플의 실험적 결과를 비교 분석 하였다.

• 콘크리트학회논문집
• /
• 제24권5호
• /
• pp.535-542
• /
• 2012

매스 콘크리트에서 발생하는 수화열을 예측하기 위한 단열온도상승시험은 시험 비용이 고가이고 시공간상 제약으로 인해 한계가 있는 실정이다. 이에 신속하고 경제적이며 간편한 간이 수화열 측정 장치의 개발이 필요한 실정이다. 이 연구에서는 간이 수화열 측정 장치를 완성하기 전 단열 성능이 뛰어난 보온병에 콘크리트를 타설하고 열손실량을 보정하여, 간이 수화열 측정 장치의 타당성을 입증하고자 하였다. 열손실량을 정확히 예측하기 위해서는 측정 장치의 정확한 열손실계수를 추정하는 것이 필수적인데, 열손실계수는 단열 장치 내부의 수온 변화를 이용하여 추정하였다. 시험 결과 장치 고유의 열손실계수는 외부 온도와 습도, 내부 온도 변화에 크게 변하지 않는 것으로 드러났다. 실제 단열온도상승시험과 열손실량이 보정된 보온병의 단열온도상승량과의 검증 시험을 통해 이 연구의 객관성과 타당성을 입증할 수 있었다.