• Macromolecular Research
• /
• v.12 no.1
• /
• pp.78-84
• /
• 2004

Advanced epoxy molding compounds (EMCs) should be considered to alleviate the thermal stress problems caused by low thermal conductivity and high elastic modulus of an EMC and by the mismatch of the coefficient of thermal expansion (CTE) between an EMC and the Si-wafer. Though A1N has some advantages, such as high thermal conductivity and mechanical strength, an A1N-filled EMC could not be applied to commercial products because of its low fluidity and high modules. To solve this problem, we used 2-$\mu\textrm{m}$ fused silica, which has low porosity and spherical shape, as a small size filler in the binary mixture of fillers. When the composition of the silica in the binary filler system reached 0.3, the fluidity of EMC was improved more than twofold and the mechanical strength was improved 1.5 times, relative to the 23-$\mu\textrm{m}$ A1N-filled EMC. In addition, the values of the elastic modules and the dielectric constant were reduced to 90％, although the thermal conductivity of EMC was reduced from 4.3 to 2.5 W/m-K, when compared with the 23-$\mu\textrm{m}$ A1N-filled EMC. Thus, the A1N/silica (7/3)-filled EMC effectively meets the requirements of an advanced electronic packaging material for commercial products, such as high thermal conductivity (more than 2 W/m-K), high fluidity, low elastic modules, low dielectric constant, and low CTE.

• Journal of Environmental Science International
• /
• v.1 no.1
• /
• pp.13-21
• /
• 1992

The inhibitory effects of mercury ions on the growth of barley seedlings were studied and the distribution of metal elements in the organs of treated plants was investigated by using synchrotron radiation induced X-ray emission (SRIXE). Although the treatment of mercury ions caused growth inhibition, the mercury-specific increase in variable fluorescence and the abolishment of energy-dependent quenching in broken barley chloroplasts as shown by Moon et at. (1992) were not observed in the leaves of growth-inhibited seedlings. Instead the treatment of mercury decreased Fmax and Fo values. However, Fmax/Fo ratio and photochemical and nonphotochemical quenching coefficients were not affected significantly. By SRIXE analysis of $10\mu\textrm{m}$ mercury chloride treated seedlings, accumulation of mercury in roots was observed after 1 hour of treatment and similar concentration was sustained for 48 hours. Relative contents of mercury was high in roots and underground nodes where seeds were attachedl but was very low in leaves. Iron and zinc were also distributed mainly in the lower parts of the seedlings. However after 72 hours of treatment the contents of these metals in roots decreased and their distribution became more uniform, which may lead to death of the plants. These results suggest that the observed inhibitory effects on barley seedlings upto 48 hours after the treatment is not due to direct damages in the photosynthetic apparatus, but due to its accumulation in roots and the consequent retardation of the growth of barley seedlings. The decrease in Fmax and Fo is probably due to the decrease in chlorophyll and protein contents caused by the retardation of growth. The observed slow expansion of primary leaves could be also explained by the retardation of growth, but the fluorescence induction pattern from the leaves did not show characteristic symptoms of leaves under water stress.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.3
• /
• pp.25-29
• /
• 2009

High temperature high humidity and thermal shock reliability tests were performed for the board level COB(chip-on-board) flip chip packages using self-formulated and commercial NCPs(non-conductive pastes) to ensure the performance of NCP flip chip packages. It was considered that the more smaller fused silica filler in prototype NCPs is more favorable for high temperature high humidity reliability. The failure of NCP interconnection was affected by the expansion of epoxy due to moisture absorption rather than the fatigue due to thermal stress. It was considered that the NCP having more higher adhesive strength seems to be more favorable to increase the thermal shock reliability.

• Journal of Sensor Science and Technology
• /
• v.8 no.5
• /
• pp.400-406
• /
• 1999

Piezoresistive flow sensors with four different types of microbeam structures were fabricated using (100), n/$n^+$/n three-layer silicon wafer and their characteristics were investigated. Piezoresistors were formed through boron diffusion and its values were about $1\;k{\Omega}$. Three-dimensional silicon microbeams were constructed by porous silicon micromachining and curled microbeams were fabricated by the difference in the thermal expansion coefficient between silicon and metal. The output response of the fabricated sensor was evaluated through half- bridge. The output voltage increased with increasing length of microbeam at the same flow velocity, while the detectable measurement range extended with decreasing length of microbeam. The output voltage of the fabricated sensors were increased with quotient of 3.2 of the flow rate since the stress of the beam versus the gas flow showed non-linear characteristics.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.8 no.2
• /
• pp.107-115
• /
• 2006

To elucidate the relation of leaf development stage to the antioxidative function in leaves of Alnus firma Sieb. et Zucc. growing in polluted areas, we investigated seasonal changes of pigment content and antioxidant enzyme activities from January to June. In abandoned mine and industrial complex areas, antioxidant function against stress of trees was changed with leaf expansion, and antioxidant activity in leaves was highest in June. Among antioxidants, carotenoid, SOD and CAT were correlated with seasonal change. Carotenoid and SOD represented a positive correlation but CAT represented a negative correlation with leaf development. APX and CAT, which remove $H_{2}O_2$, had a complementary function in the antioxidant system. The lowest antioxidant activity was observed in April, and the damage level in leaves, shown as MDA content, was also lowest in April.

• Archives of Plastic Surgery
• /
• v.37 no.6
• /
• pp.763-768
• /
• 2010

Purpose: Reconstruction of soft tissue defect using tissue expander can provide better flap which is more similar to surrounding tissue in color, skin texture and hair compared to other methods. Many pediatric patients need reconstruction of soft tissue defect because of giant congenital nevi, congenital or acquired malformations and burn scars. Reconstruction using tissue expander is adequate to minimize dysmorphism in these patients. We intended to assess outcomes of using tissue expander in pediatric patients by retrospective study. Methods: Total cases were 168 of pediatric patients who received soft tissue reconstruction using tissue expander by the same surgeon from February, 1982 to May, 2009. All patients who received soft tissue reconstruction were under 10 years old. Mean age was 4.3 years old, the youngest 13 months, the oldest 8 years. Eightynine cases were male and 79 cases were female. Most common cause was giant hairy nevi (67 cases, 39.9%), secondary cause was burn scar/scar contracture (61 cases, 36.3%). Trunk (38 cases, 22.6%) was most common anatomical location. Results: Soft tissue defects were successfully covered using tissue expander in 149 cases (88.7%) without major complications. There was infection on 8 cases (4.7%) and we treated by adequate antibiotics in these cases. There were tissue expander folding or valve displacement on 5 cases (3%). Conclusion: Usage of tissue expander is useful on pediatric patients because tissue expansion is rapid on children and there are less secondary contractures on operation site than full thickness skin graft. Because of psychological stress due to tissue expander, operation should be performed before school age.

• Journal of Korean Society on Water Environment
• /
• v.32 no.2
• /
• pp.135-141
• /
• 2016

This study investigated changes of hydrology, soil characteristics, riparian vegetation communities, and geomorphology in sandbars before and after sand-mining to determine the effect of sand-mining at upstream of Guemgang and Bochungcheon streams in Korea. Sand-mining events affected the mining area. They supplied organic matters and nutrients during flood. Sediment deposition caused soil texture change and expansion of vegetation area. However, riverbeds were stabilized after the disturbance. According to the analyses of aerial photographs, the vegetation area was significantly expanded in both dam-regulated streams and dam-unregulated streams after sand-mining. Willow shrubs advanced in disturbed area at an average of 10 years after sand-mining. It took willows trees 10.6 years to become dominant communities. Therefore, it took a total of 20.6 years for new riparian forest to form in sandbar after sand-mining. Our results confirmed that stream flow condition were dependent on vegetation recruitment in dam-regulated streams and dam-unregulated streams. For willow recruitment in unregulated streams, calculation of water level below dimensionless bed shear stress is important because low water level variation is a limiting factor of vegetation recruitment.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.167-168
• /
• 2012

Films of CrN, $Cr_{40}Zr_9N$, and $Cr_{31}Zr_{16}N$ were deposited on a steel substrate by closed field unbalanced magnetron sputtering, and their oxidation behaviors at $700^{\circ}C$ and $800^{\circ}C$ for up to 60h in air were investigated. All the deposited films were composed of the CrN phase. Zirconium atoms in $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films partially dissolved in the CrN phase. They advantageously refined the columnar structure, reduced the surface roughness, and increased the microhardness. The CrN film displayed relatively good oxidation resistance, owing to the formation of the highly protective $Cr_2O_3$ on its surface. The $Cr_{40}Zr_9N$ and $Cr_{31}Zr_{16}N$ films oxidized to $Cr_2O_3$ as the major phase and ${\alpha}-ZrO_2$ as the minor one. They oxidized primarily by the inward transport of oxygen. The addition of Zr could not increase the oxidation resistance of the CrN film, because the formed $ZrO_2$ that was intermixed in the $Cr_2O_3$-rich oxide layer was oxygen permeable, and developed the compressive stress in the oxide scale owing to the volume expansion during its formation.

• Journal of Digital Convergence
• /
• v.16 no.12
• /
• pp.611-617
• /
• 2018

This study divided hairpiece-related technologies into three categories: Materials, Structure, Hair Extensions. Then, it investigated the current patent application trends in the above technologies and attempted to determine what aspects should be focused on in terms of the growth potential of hairpiece-related technologies and future technologies. A hairpiece is used to cover a specific balding area resulting from innate factors such as heredity or acquired traits including disease or accident. It is also used to make short hair look longer. Recently, as the rates of hair loss caused by stress increase, there has been a rising demand for hairpieces that can quickly and conveniently cover a balding region as well as satisfy people's aesthetic needs through diverse hairstyling. Even though patents have been applied evenly across hairpiece technology fields, patent activity has declined since 2010 was confirmed. Therefore, this study targets the facilitation and expansion of the hairpiece technology market by suggesting desirable R&D directions for future hairpiece-related technologies after analyzing current hairpiece patent trends.

• Corrosion Science and Technology
• /
• v.18 no.4
• /
• pp.129-137
• /
• 2019

CFRP (Carbon Fiber Reinforced Plastics) is composed of carbon fiber and plastic resin, and is approximately 20 - 50% lighter than metallic materials. CFRP has a low density, higher specific stiffness, specific strength, and high corrosion resistance. Because of these excellent properties, which meet various regulation conditions needed in the industrial fields, CFRP has been widely used in many industries including aviation and ship building. However, CFRP reveals water absorption in water immersion or high humidity environments, and water absorption occurs in an epoxy not carbon fiber, and can be facilitated by higher temperature. Since these properties can induce volume expansion inside CFRP and change the internal stress state and degrade the chemical bond between the fiber and the matrix, the mechanical properties including bond strength may be lowered. This study focused on the effects of NaCl concentration (0.01 - 1% NaCl) and solution temperature ($30-75^{\circ}C$) on the galvanic corrosion between CFRP and A516Gr.55 carbon steel. When NaCl concentration increases 10 times, corrosion rate of a specimen was not affected, but that of galvanic coupled carbon steel increased by 46.9% average. However, when solution temperature increases $10^{\circ}C$, average corrosion rate increased approximately 22%, regardless of single or galvanic coupled specimen.