• Transactions of Materials Processing
• /
• v.7 no.1
• /
• pp.36-48
• /
• 1998

In order to analyze the stretch flange forming characteristics of tailored blanks. laser welded blanks of different thickness and strength combinations were prepared and hole expansion tests were done. The stretch flange formability of laser welded blanks was reduced as increasing the deformation restraining force($strength{\times}thickness$) ratio between two welded sheets. Simulation of stretch forming mode deformation and comparson with experimental results showed that the stretch flange formabili-ty was influenced not only by the difference of the deformation restraining forces between two base sheets but also by the difference of the deformation restraining forces between base sheet and weld. Therefore the stretch flange formability was reduced more rapidly than tensile elongation as increas-ing the deformation restraining force ration. It was also found that simulation of stretch flange forming was more accurate when material properties of weld was given.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.613-618
• /
• 2002

Steel slag produced in steel making process is divided with electric arc furnace slag and converter slag. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, we treat electric arc furnace slag aggregate(EAFSA) for concrete before and after several aging process to reduce expansibility. The fundamental properties are measured, which are specific gravity, unit weight, abrasion value and immersion expansion ratio, as concrete aggregate. To understand the suitability of EAFSA for concrete, we made the concrete with EAFSA and then determined the strength and the volume change in EAFSA concrete. From the results EAFSA treated with steam aging process has potentiality for concrete aggregate.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.61-63
• /
• 2005

Because of an energy efficiency and a greenhouse gas reduction effectiveness at the same time, the concern have been enlarged in the CHP But, the approach of a policy side have been achieved about the South Korea currently. This papers considered a policy side and economic side. As a result of Long Term Generation Expansion Planning from calculating the component ratio of adequate CHP, Reliability of the power system and influence of environments was analyzed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.217-220
• /
• 2006

This paper describes a study undertaken to determine the effect of ground calcium carbonate(GCC) cement mortar with respect to sulfate attack. It were investigated visual appearance and expansion of cement mortars with GCC immersed in artificial solution of 5% sodium sulfate during 510days. According to increasing replacement of GCC, the expansion ratio was comparatively superior to GCC0 mortar specimen. The test results indicated that cement mortars with GCC was benefit the resistance of sulfate attack due to micro filler effect.

• Journal of the Korean Ceramic Society
• /
• v.26 no.1
• /
• pp.43-50
• /
• 1989

This experiment was conducted to investigate correlation between microstructure and electrical properties according to Zr/Ti mole ratio in Rhombohedral Phase PZT. Domain behavoir was investigated by the change of thermal expansion coefficient. Piezoelectric properties, the temperature dependence of dielectric constant and the change of dielectric constant before and after poling were measured. Crystal structure, the measurement of lattice parameter were carried by X-ray analysis. Domain pattern before and after poling was examined by SEM.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.5
• /
• pp.293-298
• /
• 2004

For the application of heat sink device, the green sheets of powder of W-XCu and Mo-XCu composites were fabricated by tape casting technique. The mixing ratio of powder and binder was 6:4. The green sheet was shrinked up to 10~20% after sintering and the maximum relative density was above 95%. Thermal conductivity and Thermal expansion systematically increased with increasing Cu contents. The maximum thermal conductivity of W-20wt.%Cu was about 206[W/mK].

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.301-308
• /
• 2001

The problem of predicting crack propagation in anisotropic solids which is a subject of considerable practical importance is examined. The effect of the second term in the asymptotic expansion of the crack tip stress field on the direction of initial crack extension is made explicitly. We employ the normal stress ratio theory to determine values for the direction of initial crack extension. The theoretical analysis is performed for the wide range of the anisotropic material properties. It is shown that the use of second order term in the series expansion is essential for the accurate determination of crack growth direction in anisotropic solids.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.116-119
• /
• 2007

The application of light weight materials, such as aluminum alloy, has been limited due of their poor formability. Especially, aluminum alloy tube has limited expansion capability at most 15% at room temperature. New manufacturing process, called hot air forming, is introduced to apply aluminum tube to the automotive suspension components which have complex shape and require high expansion ratio about 40%. The process is carried out at the elevated temperature above $500^{\circ}C$, so numerous material properties and process parameters related to the high temperature should be investigated and determined to get a sound product. In this study, the effect of thermal properties and forming parameters such as the temperature of tool, axial feeding and gas pressure are analyzed by using explicit finite element method.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.5
• /
• pp.382-388
• /
• 2003

Refrigerant flow rates of the multi-type air-conditioning system can be regulated by electronic expansion valves (EEV). The performance of the multi-type air-conditioning system may be improved by lowering the superheat at the compressor suction side. In this study, a superheat temperature setpoint reset algorithm was developed by using fuzzy logics, and a PI algorithm was applied to control the superheat temperature near setpoints. Experimental results showed energy savings and stable operations at a multi-type air-conditioning system. Therefore, the developed setpoint reset algorithm may be effectively used for the EEV superheat temperature control of the multi-type air-conditioning system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.5
• /
• pp.735-740
• /
• 2011

본 연구에서는 직접분사식 CNG기관의 희박한계를 보다 확장하여 고효율 및 저배기 공해를 실현시키고자 실린더 내에 고압의 천연가스를 직접분사함과 동시에 흡입과정 중 흡기관 내에 소량의 저압천연가스를 보조분사하는 경우의 희박한계 확장 및 제반특성에 대해 검토하였다. 그 결과, 흡기보조분사가 없을 경우 희박한계가 ${\lambda}$ = 1.4 까지였으나, 흡기보조분사율이 5~15% 정도에서는 희박한계가 ${\lambda}$ = 1.5 까지 확장되었다. 이는 흡기보조분사에 따른 혼합기의 혼합율 향상에 기인한 것으로 해석하였다. 연소기간은 줄어들었지만, 흡기보조분사의 효과는 주연소기간에서 조기연소기간보다 강하게 나타났다.