• 한국소음진동공학회논문집
• /
• 제21권7호
• /
• pp.665-673
• /
• 2011

Simplified formulae for axial and bending natural frequencies of a bellows are developed using an equivalent thin-walled pipe model. The axial and bending stiffness of bellows is determined using lumped transfer matrix method. Transfer matrix method which includes the rotary inertia is used to calculate the natural frequencies for axial and lateral vibration. The result from the simplified formula are verified by those from as experiment result and a finite element analysis. This comparisons show good agreement with the each other.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.103-108
• /
• 2000

Since the ceramic/metal joint material is made at a high temperature, the residual stress development when it is cooled from bonding temperature to room temperature due to remarkable difference of thermal expansion coefficient between ceramic and metal. As residual stress at ceramic/metal joints influences the strength of joints, it is important to estimate residual stress quantitatively. In this study, it is attempted to estimate joint residual stress of $Si_3N_4/STS304$ joints quantitatively and to compare the strength of Joints. The difference of residual stress is measured when repeated thermal cycle is loaded under the conditions of the practical use of the ceramic/metal joint. And 4-point bending test is performed to examine the influence of residual stress on fracture strength. As a residual it is known that the stress of joint decreases as the number of thermal cycle increases.

• 한국건축시공학회지
• /
• 제15권2호
• /
• pp.185-192
• /
• 2015

기존 교량의 신축이음장치는 각종 노후화로 인해 제설제를 포함한 노면수의 누수사례가 빈번히 발생하여 교량의 수명을 감소시켜 유지관리 비용을 가중시킨다. 이러한 문제점을 해결하기 위해 신축이음장치를 사용하지 않는 고인성 연결조인트 공법을 개발하였으며, 본 연구에서는 개발된 고인성 연결조인트공법의 균열제어성능 균열 후 누수방지성능 및 염해저항성을 실험적으로 검토하였다. 그 결과, 연결조인트 소재에서 PCM, FRC를 사용한 경우에는 균열 분산성이 불량해서 누수 및 염해가 쉽게 발생하였다. 반면, 고인성 콘크리트를 사용한 연결조인트는 인장변형량이 최대 7.5mm까지 균열을 무해한 마이크로 크랙으로 안정적으로 분산시켰으며, 가혹한 조건에서도 누수를 방지할 수 있었다. 또한, 균열 후에도 염화물 이온의 침투를 방지하여 염해저항성을 확보할 수 있었다.

• 한국도로학회논문집
• /
• 제17권2호
• /
• pp.13-20
• /
• 2015

PURPOSES: This paper describes the expansion caused by the alkali-aggregate reaction (AAR) in concrete pavement currently in service. It also discusses the effects of joints installed to release the stress induced by the AAR expansion. METHODS: The expansion effect on concrete pavement was verified by a visual inspection and long-term measurement of the joint width of a cut-section. The behaviors of 16 newly installed joints were monitored as part of the investigation and long-term monitoring was carried out for three years after cutting. RESULTS: The behavior of a bridge was affected when AAR occurred in the connected pavement. The newly installed joints shrank in the longitudinal direction of the bridge after cutting. The width of the joints decreased over the six months after cutting. A large portion of the joint width (8.5cm) was found to have closed nine months after cutting. It had ultimately shrunk by about 92 percent when the final measurement was taken. CONCLUSIONS : The expansion of the pavement due to AAR was quantitatively described by visual inspection and the long-term monitoring of the newly cut joints. However, the width of the new joints decreased over the six to nine months after cutting. Additional research should be conducted to determine a means of controlling the expansion due to AAR in the pavement.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권6호
• /
• pp.33-38
• /
• 2022

지속적인 폭염이 발생함에 따라 협착으로 인한 포장 솟음이나 교량 신축이음 파손 사례가 다수 발견되고 있다. 특히 교량에서의 협착은 구조물의 안전성을 위협하거나 장기적인 내구성을 저하시킬 수 있는 중요한 문제이다. 본 논문에서는 교량에 협착이 발생할 경우에 대한 구조해석 방법을 제시하고, 대표형식 교량에 대한 협착상태 구조해석을 수행하여 그 거동 영향을 확인하였다. 대표교량은 상부구조의 경우 콘크리트교와 강교, 하부구조의 경우 직접기초와 말뚝기초로 구분하여 선정하였으며, 측방유동압, 알칼리 골재반응에 의한 포장팽창, 뒤채움재의 Creep로 인한 침하를 협착에 대한 추가적인 하중으로 고려하였다. 구조해석 결과를 실제 측정된 유간 데이터와 비교하여 구조해석 방법을 검증하였다. 또한 협착에 의한 거동 영향 분석을 수행하여 축력이 증가함에 따른 상부구조의 형식별 안전율 변화 경향을 확인하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1248-1253
• /
• 2011

It is increasing construction of long span railway bridge with concrete track system for speed up of railway and efficient maintenance of track. As the sleeper of the concrete track system layed on a bridge is fixed on deck of the bridge, the displacement of the sleeper and deck is same. Therefore, the spacing between two sleeper installed at the end of the adjacent deck near the expansion joint of bridge becomes vary according to the longitudinal expansion of a deck by temperature change. By the way, if the spacing of sleepers become increase excessively, it causes large bending stress of in a rail, and it can leads failure or reduction of fatigue life of the rail. Further more, the excessive displacement of the rail may induce decrease ride comfort as well as corrugation of rail surface. Therefore, it is required to determine the allowable maximum sleeper spacing to prevent such problems. For the purpose, investigation on the influence factor on sleeper spacing for straight track was carried out. Variation of bending moment in a rail, wheel force, and the ratio of primary and secondary deflection of the rail according to sleeper spacing was investigated, and, as a result, the maximum allowable sleeper spacing at the bridge expansion joint was suggested.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.800-806
• /
• 2011

Thermal expansion which occurs at the high speed rail joint is proportional to the free length from the point of fixity. This thermal expansion behaves similar to free expansion because the girder longitudinal stiffness is much larger than longitudinal resistance of rail pads. But the longitudinal displacement in the long rail is nominal because the longitudinal support condition of the girder is normally MFM(movable-fix-movable) system. Due to these girder expansion characteristics, there is longitudinal relative displacement at the rail pad and rail fastener spring which connects rail and girder. If the relative displacement between rail and girder is beyond the elastic limit for the rail pad, rail fastener system shall be applied using sliding fastener to prevent rail pad damage and fastener separation resulting from slip. On the other hand, train vertical vibration and tilting can occur due to the lack of fastener vertical force if the sliding fastener is applied at the girder joint. In the high speed rail bridge, vibration can occur due to the spring stiffness of the elastomeric bearing, also both vertical downward and upward displacement can occur. The elastomeric bearing vertical movement can cause rail displacement and finally the stability of the ballast is reduced because the gravel movement is induced.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1050-1055
• /
• 2008

The demand on a turnout layed on a bridge is rising owing to the increasing number of stations on the viaduct. And also the demand on a turnout with CWR is rising to upgrade running speed of the passing train. A CWR with turnout is subjected to additional axial force induced by the thermal expansion of bridge as well as lead rail of turnout. The additional axial force is closely related with the distance between bridge expansion joint and turnout when it is located near the movable bearing of bridge, and it is required to keep some distance to prevent excessive axial stress in CWR. But, there is no guideline in specification for the proper distance from E.J. to turnout, and it caused problem in planning turnout or bridge. So, it this study, the parametric study to investigate the effect on axial stress in CWR with turnout according to span length and distance between bridge expansion joint and turnout was performed. From the results of numerical analysis, it was found out that $5{\sim}30m$ distance is required to prevent excessive axial in CWR for span length less 90m.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.117-122
• /
• 2003

Cheongdam Bridge in Seoul Metropolitan Subway Line No.7 recently constructed has 180 meters (2@90m) of expansion length of structure (distance between fixed points). Track type is all ballasted track and rail expansion joint is installed at every movable point. However, there is no expansion joint at the transition area between ballasted track ,end deck. By this reason, the rail buckling has been occurred every year and there is actually an abnormal behavior in expansion. In this study, based on the modeling of the Cheongdam Bridge, the element of interacting relationship between track and structure which is influential to track displacement in long-span bridge was analyzed and, finally, the methodology to ensure the continuous-welded rail in Cheongdam Bridge was suggested.

• 한국건축시공학회지
• /
• 제10권1호
• /
• pp.65-72
• /
• 2010

교량 신축이음장치의 파손 유형은 주로 후타재(무수축 모르타르)와 관련된 부분에서 많이 발생된다. 또 다른 문제는 중차량 통과에 따른 충격과 진동하중으로 인해서 신축이음장치를 후타재에 고정하기 위해서 사용하는 앵커 풀림 현상이다. 본 연구에서는 무수축 모르타르의 파괴에 따른 신축이음장치의 파손을 방지하기 위해 탄성콘크리트를 개발하였다. 개발된 탄성콘크리트와 현재 주로 사용하고 있는 무수축 모르타르의 인발성능을 비교하였다. 또한, 후타재와 신축이음장치를 일체화하여 후타재의 파손을 방지하고 신축이음장치를 쉽게 교체할 수 있는 앵커 시스템을 개발하였다.