• Journal of Korea Multimedia Society
• /
• v.20 no.11
• /
• pp.1711-1719
• /
• 2017

In this paper, we propose a method of the zoom motion estimation for the depth video coding. The proposed method calculates the zoom ratio using the average of the depth values in the current block and in the reference block. It resizes the reference block by the zoom ratio and interpolates the reference block to size of the current block. It compares the current block with the reference block that is obtained by subtracting the average of pixels from the current block to the reference block in order to find the reference block that is the best closest one to the current block. The results of the simulation for the proposed method show that the motion estimation errors are significantly reduced.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.13 no.3
• /
• pp.75-81
• /
• 2017

This paper estimate a desired signal in a correlation wireless communication. The transmitted signal is mixed with the information signal, interference, and noise in wireless channel, and it is incident on the receiver. In this paper, we apply MUSIC algorithm and sub-array method to recover the total rank of the correlation matrix in order to estimation a desired signal among receiving signals. Through simulation, we analyze to compare the proposed method with the classical MUSIC algorithm. As a result of the simulation, the proposed method improved the resolution about 10degrees compared to the conventional MUSIC algorithm. We prove the superiority of the proposed method for the desired signal estimation in correlation channel.

• Phonetics and Speech Sciences
• /
• v.3 no.3
• /
• pp.109-114
• /
• 2011

To estimate sound direction of arrival with a pair of microphones, a method based on Time Difference of Arrival (TDOA) estimation using the Cross Power Spectrum Phase (CPSP) function is largely used due to its simplicity and good performance. In this paper, we investigate CPSP maximum values for various SNRs and adverse environments, and propose a novel method to improve the estimation performance of sound direction of arrival. The proposed method applies a threshold to the CPSP values and increases the reliability of the estimated sound direction. Through computer simulation for various SNRs, we validate the effectiveness of the proposed method. When the threshold was set to 0.1, more than 90% of success rate of sound direction of arrival estimation has been achieved for directions of $10^{\circ}$, $40^{\circ}$, $70^{\circ}$ from the source location even with reverberation times of 0.1s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10B
• /
• pp.1813-1820
• /
• 2000

In this paper we proposed an efficient multiresolution motion estimation(MRME) algorithm using half-pixel accuracy motion estimation (HPAME) and characteristics of motion vectors in the baseband. Conventional MRME method needs exact motion vectors in the baseband because those are used as initial motion vectors in higher frequency subbands. Therefore the proposed method uses HPAME to estimate the motion vectors exactly in the baseband. Based on the characteristics of these motion vectors the motion vectors in the higher frequency subbands are selectively estimatied. That is motion vectors in the higher frequency subbands are estimated only for the blocks which have the half-pixel accuracy motion vectors in the baseband. In the proposed method by using HPAME in the baseband and selective motion estimation in the higher frequency subbands we can obtain reconstructed image with the similar quality with the conventional method though we reduce the computational complexity and the bit rate considerably.

• Journal of electromagnetic engineering and science
• /
• v.4 no.1
• /
• pp.23-29
• /
• 2004

In this paper we analyze convergence constraints and time constant of IT-LMS algorithm and derive a method of making it's time constant independent of signal power by using input variance estimation. The method for estimating the input variance is to use a single-pole low-pass filter(LPF) with common smoothing parameter value, θ. The estimator is with narrow bandwidth for large θ but with wide bandwidth for small θ. This small θ gives long term average estimation(low frequency) of the fluctuating input variance well as short term variations (high frequency) of the input power. In our simulations of multipath communication channel equalization environments, the method with large θ has shown not as much improved convergence speed as the speed of the original IT-LMS algorithm. The proposed method with small θ=0.01 reach its minimum MSE in 100 samples whereas the IT-LMS converges in 200 samples. This shows the proposed, tap-power normalized IT-LMS algorithm can be applied more effectively to digital wireless communication systems.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.10
• /
• pp.522-527
• /
• 2003

This paper proposes a new speed and flux estimation method which has the robustness against the variation of the electrical parameters of the motor and the superiority in the dynamic characteristics. In the proposed method, the stator currents and the rotor fluxes are observed on the stationary reference frame using the sliding mode concept. And the rotor speed is estimated using the current estimation errors and the observed rotor fluxes based on the Lyapunov stability theory. Also a design method of the observer gain is proposed to minimize the effect of the speed estimation error on the rotor flux observation. The experimental results are shown to verify that the proposed method shows the excellent performances under the variations of motor resistance and inductance.

• Korean Journal of Computational Design and Engineering
• /
• v.22 no.2
• /
• pp.215-221
• /
• 2017

This paper describes a method of precise estimation for printing time and material consumption which are directly related to the 3D printing cost. Printing process and head motion of 3D printers using digital printing head, which is analyzed by its digitized steps, is rapidly simulated without slicing to calculate estimated printing results. Using this method, printing time and material usage of 3D printer were estimated quickly and precisely and compared to the real printing result. Applying compensation using the printing parameters, transferred from the 3D printer to the printing estimation system, even more accurate estimation is achieved. This method is used in the 3D Sprint software.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.247-250
• /
• 2006

Based on the possibility theory and the fuzzy set, the Maximum Possibility Estimation method and its applications in kinematic GPS positioning are presented in this paper. Firstly, the principle and the optimal criterion of the Maximum Possibility Estimation method are explained. Secondly, the kinematic GPS positioning model of single epoch single frequency with baseline length constraint is developed. Then, the authors introduce the artificial immune algorithm and use this algorithm to search the global optimum of the Maximum Possibility Estimation model. The results of some examples show that the method is efficient for kinematic GPS positioning.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.269-273
• /
• 2003

In the rice planted acreage estimation, high precise measurement and laborsaving are required by using satellite data. A method referring accurate agricultural plot vector data was used in this paper which improves the estimation accuracy of rice planted acreage compared with conventional methods. In this method, satellite data are not used for totalization, although they are used to discriminate whether the fields are rice planted or not. This paper described the result of the above method using to ASTER-VNIR data.

• Journal of Korean Port Research
• /
• v.10 no.2
• /
• pp.61-68
• /
• 1996

The main problems in structural analysis by Finite Eelement Method are difficulty in making data file and error estimation. For decreasing these problems' pays. have been suggesting the adaptive mesh refinement and error estimation method. Posteriory error estimation methods suggested by Jang[1], Babuska[2,3], Ohtsubo[8,9], and this paper. Comparing these methods and examine their properties. According this paper, In the problem supposed having singularity, the method suggested by this paper is good, But the problem supposed having no singularity, the method suggested by Jang[1] is good. For decreasing the effect of initial mesh in p-refinement, make application h-refinement at first and apply p-refinement, and confine polynomial's degree to two, for making program simply by plural mesh models are not needed.