• Radiation Oncology Journal
• /
• v.11 no.1
• /
• pp.175-181
• /
• 1993

Radiosurgery requires integral procedure where special devices and computer systems are needed for localization, dose planning and treatment. The aim of this work is to verify the overall mechanical accuracy of our LINAC and develop dose calculation algorithm for LINAC radiosurgery. The alignment of treatment machine and the performance testing of the entire system were extensively carried out and the basic data such as percent depth dose, off-axis ratio and output factor were measured. A three dimensional treatment planning system for stereotactic radiosurgery has been developed. We used an IBM personal computer with C programming language (IBM personal system/2, Model 80386, IBM Co., USA) for calculating the dose distribution. As a result, deviations at isocenter on gantry and table rotation for our treatment machine were acceptable since they were less than 2 mm. According to the phantom experiments, the focusing isocenter were successful by the error of less than 2 mm. Finally, the mechanical accuracy of our three dimensional planning system was confirmed by film dosimetry in sphere phantom.

• Journal of radiological science and technology
• /
• v.34 no.1
• /
• pp.43-50
• /
• 2011

In this study we modeled the varian 2100C/D linear accelerator head and multi-leaf collimator by simulation with the GEANT4 Monte Carlo toolkit. Then central axis percentage depth dose profiles and lateral dose profiles within homogeneous water phantom($50{\times}50{\times}50\;cm^3$) were evaluated with 6 MV photon beam. The simulations were performed in two stages. In the first stage, photon energy spectrum at the target were computed were computed. Then spectra data was directly irradiated in the water phantom using sampling techniques. The simulation data were compared with experimental data to evaluate the accuracy of the model. Results showed that two data were matched within 2% error boundary. The proposed method will be applied for simulation of dose calculation and dose distribution study.

• Korean Journal of Ecology and Environment
• /
• v.51 no.3
• /
• pp.205-211
• /
• 2018

In this study, we estimated the applicability of length-weight relationship-based biomass calculations by comparison of body length of genus Polyarthra collected from different habitats. Through the comparison, we also tested availability of representative species-specific biomass value of Polyarthra which is often used without length measurement. Polyarthra samples were collected from rivers (Han River and Nakdong River) and reservoir (Paldang Reservoir), and the body length was measured for statistical comparison among habitats and biomass calculations using different equations suggested previously. According to the results, the body length of Polyarthra spp. was significantly different among sampling sites, and the necessity of body length measurement for rotifer species in each situation has been suggested rather than using the representative biomass values which is fixed without considering time and space. Comparison of suggested biomass calculations based on our measured Polyarthra body length, the equation suggested by McCauley showed more reasonable range of biomass values than that suggested by EPA. In addition, in order to calculate more accurate biomass, it is necessary to measure the body length of rotifers, at least more than 44 individuals to reduce error probability to less than 5% with 99% probability. However, since direct measurement of rotifers biomass is limited, it is considered that further analyses are required for more precise application of rotifer biomass of which has high variability due to complex morphologies and species-specific cyclomorphosis often induced by biotic and abiotic factors in the habitats.

• The Korean Journal of Food And Nutrition
• /
• v.33 no.3
• /
• pp.287-298
• /
• 2020

When producing rice products, it is very important to select suitable raw materials. Therefore, in this study, the quality characteristics of 16 rice cultivars were quantified to determine the criteria for evaluating the machinability of raw rice. The L value, which can affect the color of porridge prepared from rice, was the greatest for Hwaseonchalbyeo (84.17). The water-binding capacity, related to water interaction, was high in Hyangcheola (113.2%), and water solubility was high in Shingil (22.3%). Dodamssal (42.3%, 70.7 RVU) and Hwaseonchalbyeo (4.7%, 27.8 RVU) showed lower final viscosity compared to the cultivars in which the amylose content was medium groups (16.4~21.2%, 173.6~277.2 RVU). Specifically, cultivars with high or low amylose content had a low viscosity. The characteristics of the distribution of raw rice quality data were confirmed through 11 histograms. Furthermore, amylose content vs. water solubility, water solubility vs. peak viscosity, and peak viscosity vs. final viscosity showed high correlations (r=0.542, -0.569, and 0.836 respectively, p<0.01), and clear cultivar discrimination by the standard error of the mean (0.765~10.811). In conclusion, amylose content, water solubility, and peak viscosity were considered the most suitable characteristics for the quality evaluation of raw rice.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.159-166
• /
• 2009

The purpose of this study was to develop and automatic gait event detection algorithm using single accelerometer which is attached at the top of the shoe. The sinal vector magnitude and anterior-posterior(x-axis) directional component of accelerometer were used to detect heel strike(HS) and toe off(TO), respectively. To evaluate proposed algorithm, gait event timing was compared with that by force plate and kinematic data. In experiment, 7 subjects performed 10 trials level walking with 3 different walking conditions such as fast, preferred & slow walking. An accelerometer, force plate and 3D motion capture system were used during experiment. Gait event by force plate was used as reference timing. Results showed that gait event by accelerometer is similar to that by force plate. The distribution of differences were spread about $22.33{\pm}17.45m$ for HS and $26.82{\pm}14.78m$ for To and most error was existed consistently prior to 20ms. The difference between gait event by kinematic data and developed algorithm was small. Thus it can be concluded that developed algorithm can be used during outdoor walking experiment. Further study is necessary to extract gait spatial variables by removing gravity factor.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.4
• /
• pp.191-199
• /
• 2013

It is estimated and analyzed that the design wave height and the confidence interval (hereafter CI) according to the return period using the fourteen-year wave data obtained at Pusan New Port. The functions used in the extreme value analysis are the Gumbel function, the Weibull function, and the Kernel function. The CI of the estimated wave heights was predicted using one of the Monte-Carlo simulation methods, the Bootstrap method. The analysis results of the estimated CI of the design wave height indicate that over 150 years of data is necessary in order to satisfy an approximately ${\pm}$10% CI. Also, estimating the number of practically possible data to be around 25~50, the allowable error was found to be approximately ${\pm}$16~22% for Type I PDF and ${\pm}$18~24% for Type III PDF. Whereas, the Kernel distribution method, a typical non-parametric method, shows that the CI of the method is below 40% in comparison with the CI of the other methods and the estimated design wave height is 1.2~1.6 m lower than that of the other methods.

• Journal of KIISE:Software and Applications
• /
• v.29 no.4
• /
• pp.270-277
• /
• 2002

Text filtering is a task of deciding whether a document has relevance to a specified topic. As Internet and Web becomes wide-spread and the number of documents delivered by e-mail explosively grows the importance of text filtering increases as well. The aim of this paper is to improve the accuracy of text filtering systems by using machine learning techniques. We apply AdaBoost algorithms to the filtering task. An AdaBoost algorithm generates and combines a series of simple hypotheses. Each of the hypotheses decides the relevance of a document to a topic on the basis of whether or not the document includes a certain word. We begin with an existing AdaBoost algorithm which uses weak hypotheses with their output of 1 or -1. Then we extend the algorithm to use weak hypotheses with real-valued outputs which was proposed recently to improve error reduction rates and final filtering performance. Next, we attempt to achieve further improvement in the AdaBoost's performance by first setting weights randomly according to the continuous Poisson distribution, executing AdaBoost, repeating these steps several times, and then combining all the hypotheses learned. This has the effect of mitigating the ovefitting problem which may occur when learning from a small number of data. Experiments have been performed on the real document collections used in TREC-8, a well-established text retrieval contest. This dataset includes Financial Times articles from 1992 to 1994. The experimental results show that AdaBoost with real-valued hypotheses outperforms AdaBoost with binary-valued hypotheses, and that AdaBoost iterated with random weights further improves filtering accuracy. Comparison results of all the participants of the TREC-8 filtering task are also provided.

• Journal of Korean Society for Geospatial Information Science
• /
• v.16 no.1
• /
• pp.23-32
• /
• 2008

According to recent frequent local flash flood due to climate change, the very short-term rainfall forecast using remotely sensed rainfall like radar is necessary to establish. This research is to evaluate the feasibility of GIS-based distributed model coupled with radar rainfall, which can express temporal and spatial distribution, for multipurpose dam operation during flood season. $Vflo^{TM}$ model was used as physically based distributed hydrologic model. The study area was Yongdam dam basin ($930\;km^2$) and the 3 storm events of local convective rainfall in August 2005, and the typhoon.Ewiniar.and.Bilis.collected from Jindo radar was adopted for runoff simulation. Distributed rainfall consistent with hydrologic model grid resolution was generated by using K-RainVieux, pre-processor program for radar rainfall. The local bias correction for original radar rainfall shows reasonable results of which the percent error from the gauge observation is less than 2% and the bias value is $0.886{\sim}0.908$. The parameters for the $Vflo^{TM}$ were estimated from basic GIS data such as DEM, land cover and soil map. As a result of the 3 events of multiple peak hydrographs, the bias of total accumulated runoff and peak flow is less than 20%, which can provide a reasonable base for building operational real-time short-term rainfall-runoff forecast system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.10
• /
• pp.2149-2156
• /
• 2011

In this paper, design of a new 3-dimensional (3-D) 16-ary signal constellation with constant envelope is presented and analyzed. Unlike the conventional 16-ary constellations, all signal points of the new constellation are uniformly located on the surface of a sphere so that they have a unique amplitude level and a symmetrical structure. When average power of the constellations is normalized, the presented 16-ary constellation has around 11.4% increased minimum Euclidean distance (MED) as compared to the conventional ones that have non-constant envelope. As a result, a digital communication system which exploits the presented constellation has 1.2dB improved symbol error rate (SER). While signal points of the conventional constant-envelope constellation are not distributed uniformly on the surface of a sphere, those of the proposed constellation has a completely symmetric distribution. In addition, the new signal constellation has much lower computational complexity for practical implementation than the conventional one. Hence, the proposed 3-D 16-ary signal constellation is appropriate for the application to a communication system which strongly requires a constant-envelope characteristic.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.84-92
• /
• 2014

In this study, vibrational tendon tension measurement methods are applied to estimate tension of external tendons used in segmental post-tensioned bridges. The acceleration of various length type of tendons is measured and natural frequencies are obtained using FFT (Fast Fourier Transform). The obtained natural frequencies are within 1% error regardless of sensor direction and location. On the basis of natural frequency of tendon, estimation of the tendon tension is performed by using many types of solutions such as string theory equation, multi mode estimation, practical formula estimation and stiff string with clamped-clamped boundary conditions. The results are compared with each other and have shown that the flexural stiffness is not negligible in tendons of this type causing the vibration mode to be inharmonically related. The results have shown that the method using stiff string equation with clamped-clamped boundary conditions is more accurate than the other methods. Application example of in-service bridges has shown that force distribution effects from friction at deviation blocks can be effectively detected.