• Journal of Korea Water Resources Association
• /
• v.55 no.12
• /
• pp.1053-1064
• /
• 2022

The Thiessen method, which is the current area average precipitation method, has serious structural limitations in accurately calculating the average precipitation in the watershed. In addition to the observation accuracy of the precipitation meter, errors may occur in the area average precipitation calculation depending on the arrangement of the precipitation meter and the direction of the heavy rain. When the watershed is small and the station density is sparse, in both simulation and observation history, the Thiessen method showed a peculiar tendency that the average precipitation in the watershed continues to increase and decrease rapidly for 10 minutes before and after the peak. And the average precipitation in the Thiessen basin was different from the rainfall radar at the peak time. In the case where the watershed is small but the station density is relatively high, overall, the Thiessen method did not show a trend of sawtooth-shaped over-peak, and the time-dependent fluctuations were similar. However, there was a continuous time lag of about 10 minutes between the rainfall radar observations and the ground precipitation meter observations and the average precipitation in the basin. As a result of examining the ground correction effect of the rainfall radar watershed average precipitation, the correlation between the area average precipitation after correction is rather low compared to the area average precipitation before correction, indicating that the correction effect of the current rainfall radar ground correction algorithm is not high.

• The Journal of Korean Society for Radiation Therapy
• /
• v.16 no.1
• /
• pp.57-65
• /
• 2004

Introduction : The phantom that includes high density materials such as steel was custom-made to fix lung and bone in order to evaluation inhomogeneity correction at the time of conducting radiation therapy to treat lung cancer. Using this, values resulting from the inhomogeneous correction algorithm are compared on the 2 and 3 dimensional radiation therapy planning systems. Moreover, change in dose calculation was evaluated according to inhomogeneous by comparing with the actual measurement. Materials and Methods : As for the image acquisition, inhomogeneous correction phantom(Pig's vertebra, steel(8.21g/cm3), cork(0.23 g/cm3)) that was custom-made and the CT(Volume zoom, Siemens, Germany) were used. As for the radiation therapy planning system, Marks Plan(2D) and XiO(CMS, USA, 3D) were used. To compare with the measurement value, linear accelerator(CL/1800, Varian, USA) and ion chamber were used. Image, obtained from the CT was used to obtain point dose and dose distribution from the region of interest (ROI) while on the radiation therapy planning device. After measurement was conducted under the same conditions, value on the treatment planning device and measured value were subjected to comparison and analysis. And difference between the resulting for the evaluation on the use (or non-use) of inhomogeneity correction algorithm, and diverse inhomogeneity correction algorithm that is included in the radiation therapy planning device was compared as well. Results : As result of comparing the results of measurement value on the region of interest within the inhomogeneity correction phantom and the value that resulted from the homogeneous and inhomogeneous correction, gained from the therapy planning device, margin of error of the measurement value and inhomogeneous correction value at the location 1 of the lung showed $0.8\%$ on 2D and $0.5\%$ on 3D. Margin of error of the measurement value and inhomogeneous correction value at the location 1 of the steel showed $12\%$ on 2D and $5\%$ on 3D, however, it is possible to see that the value that is not correction and the margin of error of the measurement value stand at $16\%$ and $14\%$, respectively. Moreover, values of the 3D showed lower margin of error compared to 2D. Conclusion : Revision according to the density of tissue must be executed during radiation therapy planning. To ensure a more accurate planning, use of 3D planning system is recommended more so than the 2D Planning system to ensure a more accurate revision on the therapy plan. Moreover, 3D Planning system needs to select and use the most accurate and appropriate inhomogeneous correction algorithm through actual measurement. In addition, comparison and analysis through TLD or film dosimetry are needed.

• Proceedings of the KAIS Fall Conference
• /
• 2002.05a
• /
• pp.106-108
• /
• 2002

반도체 physical layout design rule이 작아짐에 따라 Proximity effect와 overlay가 Pattern 구현에 크게 영향을 미치고 있다. Metal layer와 contact의 부족한 overlay margin으로 overlay 불량이 발생하고, 감소한 space margin으로 인해 bridge와 같은 문제가 나타난다. 따라서, resolution을 향상시키고, 최소한의 overlay margin을 확보함으로써 미세 pattern의 구현을 가능하게 한다. 이를 위해 OPC와 attPSM 같은 분해능향상기술이 사용된다. 그러나 attPSM의 사용은 원하지 않는 pattern이 생성되는 sidelobe와 같은 문제가 발생한다. 따라서 serial image simulation올 통해 추출한 rule을 rule-based correction에 적용하여 sidelobe현상을 방지한다. 그리고 overlay margin 부족으로 나타나는 문제는 metal layer와 contact overlap되는 영역의 line edge를 확장하고, rule checking을 통해 최소한의 space margin을 확보하여 해결한다 따라서 overlay error를 rule-based correction을 사용하여 효과적으로 방지한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.244-254
• /
• 2002

To enhance the acceleration performance and fuel consumption rate of a vehicle, the torque converter is modified or newly-developed with reliable analysis model. Up to recently, the one dimensional performance model has been used for the analysis and design of torque converter. The model is described with constant parameters based on the concept of mean flow path. When it is used in practice, some experiential correction factors are needed to minimize tole estimated error. These factors have poor physical meaning and cannot be applied confidently to the other specification of torque converter. In this study, the detail dynamic model of torque converter is presented to establish the physical meaning of correction factors. To verify the validity of model, performance test was carried out with various input speed and oil temperature. The effect of oil temperature on the performance is analysed, and it is applied to the dynamic model. And, to obtain the internal flow pattern of torque converter, CFD(Computational Fluid Dyanmics) analysis is carried out on three-dimensional turbulent flow. Correction factors are determined from the internal flow pattern, and their variation is presented with the speed ratio of torque converter. Finally, the sensitivity of correction factors to the speed ratio is studied for the case of changing capacity factor with maintaining torque ratio.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.4
• /
• pp.47-56
• /
• 2005

In GPS/INS/barometer navigation system for UAV, vertical channel damping loop was introduced to suppress divergence of the vertical axis error of INS, which could be reduced to the level of accuracy of pressure altitude measured by a pitot-static tube. Because static pressure measured by the pitot-static tube depends on the speed and attitude of the vehicle, static pressure error models, based on aerodynamic data from wind tunnel test, CFD analysis, and flight test, were applied to reduce the error of pressure altitude. Through flight tests and sensitivity analyses, the error model using the ratio of differential pressure and static pressure turned out to be superior to the model using only differential pressure, especially in case of high altitude flight. Both models were proposed to compensate the effect of vehicle speed change and used differential and static pressure which could be obtained directly from the output of pressure transducer.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.349-354
• /
• 2002

A size of low-voltage conductor cables is determined by the voltage drop of a system, the cable impedance and the cable ampacity based on temperature correction factor in accordance with the condition of cable installation. Therefore, the proper temperature correction factor according to the condition of cable installation should be applied to determining the cable ampacity and also the skin effect and proximity effect, along with the kind and size of conductor and the condition of cable installation, should be properly considered to analyze the proper value of resistance and the reactance of the conductors. This paper addresses the systematic design flow for determining the size of low voltage level conductor cables in calculating the temperature character where error should be minimized in comparison with the general formula and which can be applied in design work for determining the size of conductor cables.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.4
• /
• pp.1-7
• /
• 1985

In this paper, a more improved threshold voltage model dependent on drain voltage and substrate bias for short - channel enhancement - mode IGFET is presented. Especially, compared with the several recently published models, the error is sufficiently reduced with the precise analysis on the correction factor for short-channel effect and the calculated values using this model are also agreed well with the experimental data about 1$\mu$m - channel length device.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2310-2318
• /
• 2018

Critical conduction mode (CRM) operation is more efficient than continuous conduction mode (CCM) operation at low power levels because of the valley switching of switches and elimination of the reverse recovery losses of boost diodes. When using a sensorless digital control method, an error occurs between the actual and the estimated current. Because of the error, it operates as CCM or discontinuous conduction mode (DCM) during CRM operation and also has an adverse effect on THD of input current. In this paper, a current sensorless technique is presented in an inverter system using a bridgeless boosted power factor correction converter, and a compensation method is proposed to reduce CRM calculation error. The validity of the proposed method is verified by simulation and experiment.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.69-75
• /
• 2010

Advanced T-DMB(Terrestial DMB )system which is a new portable mobile broadcasting system has been developed to increase data rate up to double of conventional T-DMB in same bandwidth while maintaining backward compatibility, using hierarchical modulation method. The Advanced T-DMB system realize high qualification of conventional T-DMB system by adding BPSK signal or QPSK signal as enhanced layer to existing DQPSK signal. The enhanced layer signal should be small enough to maintain backward compatibility and to minimize the coverage loss of existing T-DMB service area. But this causes the enhanced layer signal of Advanced T-DMB susceptible to fading effect in transmission channel. In this paper we applied the duo-binary turbo code which has powerful error correction capability to the enhanced layer signal for compensating channel distortion. And the computer simulation results about the performance of the duo-binary turbo code in Advanced T-DMB system are presented along with analysis comments.

• The Korean Journal of Financial Management
• /
• v.21 no.1
• /
• pp.125-148
• /
• 2004

This paper deals with the relationship between money supply and the stock market. However, unlike past works, it has employed a rational expectation hypothesis and an efficient market hypothesis drawn from new classical macroeconomics and new Keynesian macro-economics, respectively. Accordingly, hypothesis 1 states that if economic subjects have rational expectation, they will immediately respond to a change in money supply. On the other hand, hypothesis 2 supposes that the expectation of economic subjects has changed after the currency crisis. This paper has first identified unit root by using the augmented Dickey-Fuller test and the Phillips-Perron test, then testing both hypotheses by employing the Johansen Procedure and vector error correction model for the periods before and after a currency crisis.