• Journal of Korean Society for Quality Management
• /
• v.21 no.2
• /
• pp.1-16
• /
• 1993

Early generations of products had little to no inherent capability to test themselves. The technologies involved often required only visual inspection and limited probing to troubleshoot the system once it was turned over to maintenance personnel. However, as the complexity of military and commercial systems grew, symptoms of failure became less noticeable to the operator. Therefore, the procedure to access, inspect, repair and replace a component became complicated, the requirements for personnel skill and testing equipment increased. and it took too long of a time to maintain a system. Meanwhile, the need for availability became more mission-critical and maintenance become very expensive. The obvious solution was to design in-system circuits or devices to self-test the primary system, the Built-In-Test(BIT) was born. This approach has continued right on up through present systems and is an integral part of systems now being designed. The object of this paper is to present a state-of-the-art research for filtering out the BIT diagnosis mistakes using Bayesian analysis and develop the algorithm for Redundant systems with BIT to improve BIT diagnosis.

• Korean Journal of Oriental Medicine
• /
• v.16 no.3
• /
• pp.135-140
• /
• 2010

The usefulness of constitutional diagnoses based on skin measurements has been established in oriental medicine. According to Sasang constitutional medicine, humans can be distinguished based on properties of skin's friction, thickness and elasticity. To quantify and standardize skin diagnosis, the present study designed an equipment for measuring skin elasticity of hand. But there were some noises in measuring skin elasticity such as measurement method, environment, operator and conditions of patient. So we considered a six sigma project for reducing the measurement errors. The project was followed to discipline process of five macro phases: Define, Measure, Analyze, Improve and Control(DMAIC). So, we could find the major factors which should be controled for stabilizing measurement system and we revised the SOP(Standard Operating Procedure) of the skin elasticity measurement.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.7
• /
• pp.816-823
• /
• 2018

The Auto-synchronizer is essential equipment for synchronizing a generator to the power system. It is performing that measurement of the magnitude, frequency and phase of the voltage signal of the power system and generator. It is important to select the appropriate measurement algorithm for preventing various problem such as mechanical stress and Electrical problem. Teager Energy Operator(TEO) and Discrete separation algorithm(DESA) is measurable the instantaneous parameters of a sine wave using 5 samples and can be measured at a fast and with a simple operation. Therefore it has many advantages in measuring the parameters. In this paper, it confirmed measurement results using matlab simulations when there are synchronized in order of frequency, magnitude. Also it presented methods using digital filters and sample intervals to improve accuracy.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.261-267
• /
• 2015

A support system which allows operator to check the condition of a vessel and to warn the sea risk in order to prevent accidents of leisure boats, is required. Therefore, this paper proposes a navigational safety support system to ensure the safety of vessels by monitoring and managing the status of those ships. In developing a system process, each developed equipment is integrated and verified whether the functional, compositional and operational algorithms are working properly according to the designed object.

• Journal of the Korean Society of Systems Engineering
• /
• v.11 no.2
• /
• pp.41-49
• /
• 2015

Industrial safety is one of the crucial agenda for Government as well as Manufacturing Industry. To cope with the needs, a great deal of policies and technical implementation have been proposed and implemented. With a great increasing attention on the Industry 4.0 and Smart Factory, industrial safety has received as a crucial agenda by the manufacturing industry in particular. Up until now, almost all of them have been made from the environmental aspects, rather than operator or workers. In this paper, we present our research results how to increase the workers' safety via smart factory technology, such as IoT and CPS. Our approach has been to see the problem from SE perspectives, to draw the real issues from the various stakeholders, and define how to solve the problem based on the emerging technologies. The developed systems can give conceptual framework for the 'smart' industrial safety system by providing solution architecture for how to monitor the location of workers, and moving equipments, and generate solutions how to avoid safety problems between them if detected.

• Journal of radiological science and technology
• /
• v.22 no.2
• /
• pp.23-26
• /
• 1999

The Zygomatic arch is structurally protruded and is easily fractured. The classic management of zygomatic arch fracture has been mentioned the Keen, Lothrop, Dingman and Ailing and threaded K-wire. All of the above methods have advantages and disadvantages. To minimize the disadvantages, we performed threaded K-wire for the first time using C-arm image intensifier. The subjects were 16 patients with Knight North group II (Zygomatic arch fracture). Among them the C-arm was used in 12 patients and the operator used sensitivity general method in 4 patients and confirmed the operation by mobile X-ray equipment. In conclusion, both groups were satisfied surgically and cosmetically. Using the C-arm, actual image at the time operation was clear and satisfied, the surrounding tissue damage was minimized and at was more accurately completed. The operation time was shortened by 30 to 60 minutes proving it to be an efficient method. We suggest though that further studies be needed to evaluate the radiation effect on these patients.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.3 s.357
• /
• pp.12-19
• /
• 2007

This paper proposes the enhanced auto-focus algorithm detecting several objects and selecting the target object. Proposed algorithm first detects some objects distributed in the image using focus measure operator and multi-window and then selects the target object through fuzzy reasoning with three fuzzy membership functions. Implementation can be simple because it only needs image sensor instead of infrared or ultrasonic equipment. Experimental result shows that the proposed algorithm can improve the quality of image by focusing to the target object.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2004.11a
• /
• pp.625-628
• /
• 2004

Even though the tower crane is a major equipment in a construction of high rise buildings, there are lack of studies of it. This study is presenting a framework of developing a intelligent tower crane applied with the technology of machine-vision, RFID(Radio Frequency Identification), or GPS(Global positioning System) and proposing the prototype of machine-vision module, sub module of this Framework. Through monitoring form CCTV(Closed Circuit Television) and LCD(Liquid Crystal Display) in machine-module the real time communication between in-site workers and crane operator is possible. this will improve the productivity and safety of the tower crane.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.256-262
• /
• 2015

This study has an innovative improvement of the ocher tiles production system that aims to resolve social issue of industrial waste and to meet the customer needs for environmental-friendly building materials. By changing a wet type cutting method to a dry type of ocher tiles production system, the three processes such as cleaning, dehydration, and drying can be removed in existing overall process of 17 steps. Accordingly, the application of the wet type cutting method, which is proposed in this study, makes an increase in ocher tiles production from 1,500 to 1,850 pieces per hour. In particular, industrial wastewater that was emerging as the biggest problem in environmental pollutants in the wet cutting method has been removed. In addition, the most serious problems of noise and dust from the operator side, while developing a device for the dry cutting method, are eliminated through the development of additional equipment.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.616-624
• /
• 2016

Design of shelter system requires consideration of noise at operators’ positions, because noise can injure person’s health. That is why studies which analyze and predict noise at operator’s positions is essential. To analyze noise sources of shelter system, this study measured noise of each equipment and obtained new equations by comparing the measured noise data and the equation which is relation noise and distance. The new equations predict noise level at operators’ positions. Actran analysis is performed to obtain noise level at operators’ positions too. At last, the noise level at operators’ positions measured in real shelter system is compared with the noise level predicted the new equations and Actran analysis.