• Journal of Magnetics
• /
• 제6권4호
• /
• pp.129-131
• /
• 2001

In order to investigate the effect of the interface on GMR, [NiFe(25 ${\AA}$)/Cu(24${\AA}$)]$_2$/Si thin film was epitaxially grown on HF-treated Si (001) substrate using a DC magnetron sputtering method. Typical GMR effects could be observed in epitaxial film with a weak antiferromagnetic exchange coupling while non epitaxial film showed unsaturated and broad MR curves probably due to inter-diffusion between NiFe and Cu layers. Ferromagnetic resonance (FMR) experiment showed two distinct absorption peaks in all films. Each peak was revealed to come from each NiFe layer with different magnetic property. In FMR measurement very clear interface in epitaxial films could be confirmed by a lower value of line width (ΔH) and higher M$\sub$s/ of epitaxial film than those of non epitaxial films, respectively.

• Current Photovoltaic Research
• /
• 제2권1호
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Current Photovoltaic Research
• /
• 제1권2호
• /
• pp.103-108
• /
• 2013

Epitaxial growth of a high-quality thin Si film is essential for the application to low-cost thin-film Si solar cells. A polycrystalline Si film was grown on a $SiO_2$ substrate at $450^{\circ}C$ by a Al-assisted crystal growth process. For the purpose, a thin Al layer was deposited on the $SiO_2$ substrate for Al-assisted crystal growth. However, the epitaxial growth of Si film resulted in a rough surface with humps. Then, we introduced a thin amorphous Si seed layer on the Al film to minimize the initial roughness of Si film. With the help of the Si seed layer, the surface of the epitaxial Si film was smooth and the crystallinity of the Si film was much improved. The grain size of the $1.5-{\mu}m$-thick Si film was as large as 1 mm. The Al content in the Si film was 3.7% and the hole concentration was estimated to be $3{\times}10^{17}/cm^3$, which was one order of magnitude higher than desirable value for Si base layer. The results suggest that Al-doped Si layer could be use as a seed layer for additional epitaxial growth of intrinsic or boron-doped Si layer because the Al-doped Si layer has large grains.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2004년도 추계 기술심포지움 초록집
• /
• pp.50-50
• /
• 2004

• 한국결정성장학회지
• /
• 제9권5호
• /
• pp.504-509
• /
• 1999

In-situ cleaning and subsequent silicon epitaxial film growth were performed in a load-locked reactor equipped with Hg-grid UV lamp and PBN heater to obtain the smooth and contaminant-free underlying surface and develop low-temperature epitaxial film growth process. The removals of organic and native oxide were investigated using UV-excited $O_2$ and $NF_{3}/H_{2}$, and the effect of the surface condition was examined on the quality of silicon epitaxial film grown at temperature as low as $750^{\circ}C$. UV-excited gas phase cleaning was found to be effective in removing the organic and native oxide successfully providing a smooth surface with RMS roughness of 0.5$\AA$ at optimal condition. Crystalline quality of epitaxial film was determined by smoothness of cleaned surface and the presence of native oxide and impurity. Crystalline defects such as dislocation loops or voids due to the surface roughness were observed by XTEM.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.298-303
• /
• 2001

The critical thickness of an epitaxial film on a substrate in electronic or optoelectronic devices is studied on the basis of equilibrium dislocation analysis. Two geometric models, a single dislocation and an array of dislocations in heteroepitaxial system, are considered respectively to calculate the misfit dislocation formation energy. The isotropic linearly elastic stress fields for the models are obtained by means of complex potential method combined with alternating technique, and are used for calculating the formation energies. As a result, the effect of elastic mismatch between film and substrate on critical thickness is presented and $Si_xGe_{1-x}/Si$ epitaxial structure is analyzed to predict the critical thickness with varying germanium concentration.

• 한국결정성장학회지
• /
• 제10권6호
• /
• pp.378-380
• /
• 2000

The epitaxial $BaTiO_{3}$ thin film was prepared on the MgO substrate by the coating-pyrolysis process using a mixed solution of Ba-naphthenate and Ti-naphthenate. The crystal structure of the epitaxial $BaTiO_{3}$ thin film was characterized by XRD ${\theta}/2{\theta}$ scan and asymmetric {303} rocking curve scan. The epitaxial $BaTiO_{3}$ thin film had the cubic phase with the lattice parameter of a = c = 0.4018 nm.

• 한국결정성장학회지
• /
• 제30권1호
• /
• pp.1-6
• /
• 2020

본 연구에서는 패턴화된 사파이어 기판 위에 HVPE(Hydride Vapor Phase Epitaxy System) 법에 의해 50 nm 두께의 AlN thin film을 증착한 뒤, 에피층 구조가 MO CVD에서 성장되었다. AlN 버퍼층 박막의 표면형상이 SEM, AFM에 의해서, 에피층 구조의 GaN 박막의 결정성은 X-선 rocking curve에 의해 분석되었다. 패턴화된 사파이어 기판 위에 증착된 GaN 박막은, 사파이어 기판 위에 증착된 GaN 박막의 경우보다 XRD 피크 세기가 다소 높은 결과를 나타냈다. AFM 표면 형상에서 사파이어 기판 위에 AlN 박막이 증착된 경우, GaN 에피층 박막의 p-side 쪽의 v-pit 밀도가 상대적으로 낮았으며, 결함밀도가 낮게 관찰되었다. 또한, AlN 버퍼층이 증착된 에피층 구조는 AlN 박막이 없는 에피층의 광출력에 비해 높은 값을 나타냈다.

• E2M - 전기 전자와 첨단 소재
• /
• 제16권9호
• /
• pp.63.2-64
• /
• 2003

Epitaxial yttrium-stabilized HfO$_2$ thin films were deposited on p-type (100) Si substrates by pulsed laser deposition at a relatively lower substrate temperature of 550. Transmission electron microscopy observation revealed a fixed orientation relationship between the epitaxial film and Si; that is, (100)Si.(100)HfO$_2$ and [001]Si/[001]HfO$_2$. The film/Si interface is not atomically flat, suggesting possible interfacial reaction and diffusion, X-ray photoelectron spectrum analysis also revealed the interfacial reaction and diffusion evidenced by Hf silicate and Hf-Si bond formation at the interface. The epitaxial growth of the yttrium stabilized HfO$_2$ thin film on bare Si is via a direct growth mechanism without involoving the reaction between Hf atoms and SiO$_2$ layer. High-frequency capacitance-voltage measurement on an as-grown 40-A yttrium-stabilized HfO$_2$ epitaxial film yielded an dielectric constant of about 14 and equivalent oxide thickness to SiO$_2$ of 12 A. The leakage current density is 7.0${\times}$ 10e-2 A/$\textrm{cm}^2$ at 1V gate bias voltage.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.264.2-264.2
• /
• 2013

Molecular layer deposition (MLD) is sequential, self-limiting surface reaction to form conformal and ultrathin polymer film. This technique generally uses bifunctional precursors for stepwise sequential surface reaction and entirely organic polymer films. Also, in comparison with solution-based technique, because MLD is vapor-phase deposition based on ALD, it allows epitaxial growth of molecular layer on substrate and is especially good for surface reaction or coating of nanostructure such as nanopore, nanochannel, nanwire array and so on. In this study, polyurea film that consisted of phenylenediisocyanate and phenylenediamine was formed by MLD technique. In situ Fourier Transform Infrared (FTIR) measurement on high surface area SiO2 substrate was used to monitor the growth of polyurethane and polyurea film. Also, to investigate orientation of chemical bonding formed polymer film, plan-polarized grazing angle FTIR spectroscopy was used and it showed epitaxial growth and uniform orientation of chemical bones of polyurea films.