• Korean Journal of Agricultural Science
• /
• v.2 no.1
• /
• pp.257-264
• /
• 1975

This research was attempted as one of a study for investigating optimum contents of fly ash and briquette ash when they were used as admixtures. In mix designs of mortar, fly ash and briquette ash to cement, each of them, was mixed with 0, 5, 10, 15, 20, 25, 30 percent by weight of cement. They were tested for compressive strength, tension strength and bending strength, and these results were summarized as follows; 1. The compressive strength of mortar to add fly ash showed the maximum value at 25 percent. tension strength, 20 percent, bending strength, 15 percent. 2. In case of using briquette ash, compressive strength showed maximum strength at 15 percent. tension strength, 20 percent, bending strength, 20 percent. 3. To add fly ash showed in general more additive effect than to add briquette ash. 4. It was not only to excess standard strength but may be to develop as admixture when briquette ash was used around 20 percent.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.61-65
• /
• 2003

Bottom ash among the coal ash is not used because of its poor properties. But encouraging the use of bottom ash as a construction material is a sensible method of utilization as it avoids the problems and costs associated with disposal and provides an alternative aggregate source. This study was aimed at using bottom ash as an alternative fine aggregate source to provide a solution to disposal and insufficient fine aggregate for the production of concrete. So properties of domestic bottom ash were estimated due to the difference of each domestic bottom ash. And compressive strength and durability were estimated as basic data to use bottom ash in building industries. As a result of the experiment, the very porous surface and angular shape of the bottom ash particles necessitate a higher apparent water-cement ratio. And due to the higher water requirement, the compressive strength and durability of mortar is lower than those of the control samples. But when 25 percent of the total dry weight of the natural fine aggregate was replaced by bottom ash, the engineering characteristics were similar.

• Computers and Concrete
• /
• v.20 no.3
• /
• pp.283-290
• /
• 2017

The aim of this study is to investigate the effect of the bond strength of self-compacting mortars (SCMS) produced from ground pumice powder (GPP) as a mineral additive. In this scope, six series of mortars including control mix were prepared that consist of 7%, 12%, 17%, 22% and 27% of ground pumice powder by weight of cement. A total of 54 specimens of $40{\times}40{\times}160mm$ were produced and cured at the age of 3, 28 and 90-day for compressive and tensile strength tests and 18 specimens of $150{\times}150{\times}150mm$ mortar were prepared and cured at 28 days for bond strength tests. Flexural tensile strength and compressive strength of $40{\times}40{\times}160mm$ specimens were measured at the curing age of 7, 28 and 90-day. Mini V-funnel flow time and mini slump flow diameter tests were also conducted to obtain rheological properties. As a result of the study, it was observed that the SCMs containing 12% of GPP has the highest bond strength as compared to control and GPP mortars. Compressive strength slightly increased up to 12% of GPP.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.6
• /
• pp.538-546
• /
• 2011

This paper is to experimentally investigate the strength and autogenous shrinkage of high strength mortar with the 20 % of water?binder ratio(W/B). In this study, the water substituting liquid(WSL) was used including gasoline, light oil, lamp oil, edible oil, HFE, ethanol, methanol and acetone in order to explore changes in strength and autogenous shrinkage depending on WSL type and replacement. For fresh properties, the replacement of WSL did not affect the fluidity of mortar mixtures considerably, except for ethanol and methanol. However, the replacement of WSL resulted in a slight decrease in flexural and compressive strength. For autogenous shrinkage, the replacement of WSL led to reduce autogenous shrinkage, and especially, the replacement of edible oil led to reduce autogenous shrinkage significantly due to saponification between edible oil and cement.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.676-681
• /
• 2016

For the purpose of reducing the amount of limestone, which is used as a desulfurization agent to absorbing $SO_X$ gas in thermal power plants, and to recycle limestone sludge generated from a steel mill, limestone sludge was utilized as a desulfurization agent. In this study, cement, made of flue gas desulfurization (FGD) gypsum obtained in a desulfurization process using limestone sludge, was manufactured then, experiments were conducted to identify the physical properties of the paste and mortar using the cement. The results of the crystal phase and microstructure analyses showed that the hydration product of the manufactured cement was similar to that of ordinary Portland cement. No significant decline of workability or compressive strength was observed for any of the specimens. From the results of the experiment, it was determined that FGD gypsum manufactured from limestone sludge did not influence the physical properties of the cement also, quality change did not occur with the use of limestone sludge in the flue gas desulfurization process.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.4
• /
• pp.305-311
• /
• 2020

Polymer modified cement mortar (PCM) can improve the performance of adhesion strength, flexural strength, chemical resistance, etc., compared with cement mortar, and is widely used when repairing RC structures. However, PCM causes a burst in an environment with high temperature and fire rate, which causes problems in the stability of the structure. In this study, for the purpose of developing explosive reduction PCM, the polymer mixing ratio is 2%, 4%, 6%, the fiber length is 6mm, 12mm, 6+12mm, and the PP fiber mixing rate is 0.05 Vol% and 0.1 Vol%. Furnace heating experiment (600℃, 800℃) was carried out. As a result of comparative analysis of the explosive properties, it was confirmed that the explosive reduction effect due to the fiber incorporation was insufficient when the polymer mixing amount was 6% or more.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.395-398
• /
• 2003

This study is performed to evaluate the engineering properties of cement mortar with hwangtoh and fly ash The absorption ratio is in the range of $5.22{\sim}13.16%\;and\;8.53{\sim}13.29%$ at the curing age 14 and 28 days, respectively. The compressive strength is in the range of $92{\sim}458kgf/cm^2\;and\;88{\sim}316kgf/cm^2$ in water and dry cruing at the curing age 28days, respectively. The bending strength and dynamic modulus of elasticity are shown in similar tendency in water and dry curing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.121-124
• /
• 2005

As a countermeasure about that, in this situation that suggest utilizing mixed drush sand and particle washed sand, this study is reviewing and comparing, as a experimental and positive test, mixed both workability and engineering properties of mortar, The purpose of this study make a suggestion that is fundamental data for utilizing mixed crush sand and particle washed sand.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.438-444
• /
• 2019

In this study, the effect of polypropylene fiber on the freeze-thaw damage of mortar was evaluated experimentally. The effects of the reinforcing of polypropylene fiber on the compressive and bending performance of mortar after 300 cycles of freeze-thaw test were evaluated by comparing the normal mortar and the mortar with polyvinyl alcohol fiber. In addition, the mass loss, relative dynamic elastic modulus, and cumulated pore volume of mortar were measured by each cycle of freeze-thaw test. As a result, it was confirmed that the fiber reinforced mortar, regardless of the fiber type, was effective not only in maintaining the performance of the compressive strength and the bending strength but also suppressing the mass loss after the freeze-thaw test of 300 cycles. Meanwhile, it was confirmed that not only polyvinyl alcohol fibers but also polypropylene fibers can effectively act to suppress the damage of the mortar by freeze-thaw. However, in order to improve the freeze-thaw resistance of mortar mixed with polypropylene fiber, it is necessary to increase the bonding performance with the cement matrix which can be expected from polyvinyl alcohol fiber.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.5
• /
• pp.615-627
• /
• 2024

This study presents fundamental research data on the application and utility of biochar in Engineered Cementitious Composites (ECC) for carbon sequestration. The study experimentally measures and compares the compressive strength, tensile strength, and flexural strength of high-toughness biochar-incorporated ECC (BE) and biochar-incorporated mortar (BM) with varying levels of biochar replacement. This study aims to compare BM and BE. BM shows an increase in mechanical properties at a biochar content of 1 %. BE shows an increase in mechanical properties at a biochar content of 2 %. The reason for the increase is that biochar particles fill the voids between the binder materials, acting as a filler. This helps form a denser structure. These findings suggest that incorporating biochar into mortar and ECC can enhance their mechanical properties at optimal biochar contents.