• Journal of the Korean Solar Energy Society
• /
• v.32 no.2
• /
• pp.42-49
• /
• 2012

In this article, the author carried out a theoretical study on the application techniques of a new Combined Passive Solar System (hereinafter referred to as the CPSS) of direct gain and trombe walls to get quick morning heating and to prevent afternoon overheating for office building. The numerical model proposed in this study can be used for the performance analysis of the CPSS in the winter and summer. Heating and Cooling loads are analysed for building energy consumption reduction using this numerical model. The results indicate that CPSS in the winter and summer modes could provide profitable conditions for improvement of indoor thermal comfort control and energy saving. consequently, the application of CPSS will not lead to significant reductions in the auxiliary air conditioning demand but also realize the environmentally friendly building.

• Journal of Communications and Networks
• /
• v.10 no.2
• /
• pp.213-220
• /
• 2008

This paper analyzes a broadcasting technique for wireless multi-hop sensor networks that uses a form of cooperative diversity called opportunistic large arrays (OLAs). We propose a method for autonomous scheduling of the nodes, which limits the nodes that relay and saves as much as 32% of the transmit energy compared to other broadcast approaches, without requiring global positioning system (GPS), individual node addressing, or inter-node interaction. This energy-saving is a result of cross-layer interaction, in the sense that the medium access control (MAC) and routing functions are partially executed in the physical (PHY) layer. Our proposed method is called OLA with a transmission threshold (OLA-T), where a node compares its received power to a threshold to decide if it should forward. We also investigate OLA with variable threshold (OLA-VT), which optimizes the thresholds as a function of level. OLA-T and OLA-VT are compared with OLA broadcasting without a transmission threshold, each in their minimum energy configuration, using an analytical method under the orthogonal and continuum assumptions. The trade-off between the number of OLA levels (or hops) required to achieve successful network broadcast and transmission energy saved is investigated. The results based on the analytical assumptions are confirmed with Monte Carlo simulations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.4
• /
• pp.791-797
• /
• 2017

Recently, as energy use increases, interest in efficient energy management using ICT is increasing, and researches related to these technologies are being actively carried out. Research and commercialization of an integrated power management network model is receiving the most attention. In this paper, the current status and characteristics of technologies for energy use and management are reviewed.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.48-53
• /
• 2008

The performances of the building service equipment relay on the individual superintendent's share for the assessment of performance, fault detection, deterioration diagnosis of the building service equipment. A major use of building energy management system(BEMS) is for monitoring plant and building's energy consumption. National building management system (N-BMS) presented in this study links buildings into a network group in order to monitor and control the buildings. How to construct the N-BMS was considered to save energy resource and to conserve performance of building service equipment. The FEMIS, facility, energy/environmental management & information system, for building service offer management process integrated with BAS, FMS and EMS and so on.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6759-6765
• /
• 2015

In this study, the effects of control strategies of night-purge control system on control characteristics and energy consumption for central cooling system in building are researched by simulation. The start time and set-point temperature for night-purge control with outdoor temperature changes and building cold storage performance are obtained. The system analysis modelling is done by using TRNSYS program package, and the control performances with suggested night-purge control method are compared with the existing control ones. As a result, the suggested night-purge control method shows maximum 16.8% and 28.6% energy saving in comparison with existing control method and conventional one without night-purge control, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.401-401
• /
• 2009

Recently, demands for the development of compact, lightweight power supplies with higher power density and higher efficiency have been increased. Since Piezoelectric Transformer (PT) was emerged in device and material industry, it has been suggested as a viable alternative to the magnetic transformer in some applications. PT has some advantages such as low profile and mechanical energy transfer with little electromagnetic interface (EMI). Also, PT can provide high voltage stepping ratio with good isolation and requires no copper windings saving copper usage especially for large voltage conversion differences. Conventional control of PT converter has mainly two-way. One is the pulse frequency modulation (PFM) control method and the other is the pulse width modulation (PWM) control with frequency fixed method. It is known that the maximum PT efficiency can be obtained when it operates near the resonant frequency of the PT. And, also PT's resonant frequency moves according to the load condition. Therefore, selection of PT converter control method is very difficult. This paper analyzes general piezo-electric converter modeling and proposes a guide-line to selection of control method and stabilization control.

• Korean Journal of Agricultural Science
• /
• v.41 no.3
• /
• pp.251-258
• /
• 2014

In order to set up the basic environmental control systems which the new concept greenhouses have to equip, greenhouse characteristics, environmental management and control systems in domestic glasshouses and plastic houses were investigated and analyzed comparatively. Survey results on the width, length, eaves height, and the number of spans etc. showed that glasshouses were bigger than plastic houses significantly. New concept greenhouses claim to be plastic houses, but it will be reasonable to follow the specifications of the glasshouse. Specifications to be applied to new concept greenhouses were proposed as follows; hot water heating systems, aluminum screens as the thermal curtain, evaporative cooling systems, roof vents on the ridge, circulation fans, $CO_2$ enrichment, hydroponic systems, and automatic irrigation control systems. Environmental measurement systems for the indoor and outdoor temperature, humidity, light, wind speed and indoor $CO_2$ concentration have to be fully equipped. The automatic control system has to be as a complex environmental control system, not a single item control system. Also, for stable dissemination, domestically producing complete greenhouse control system should be made as soon as possible.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.6
• /
• pp.543-550
• /
• 2003

In order to saving the energy for HVAC system of buildings, utilization of wind-induced cross ventilation is thought to be promising. However, utilization of natural ventilation alone is not sufficient for maintaining the human thermal-comfort such as in hot and humid regions. A hybrid air conditioning system with a controlled natural ventilation system, or combination of natural ventilation with mechanical air conditioning is thought to overcome the deficiency of wind-driven cross ventilation and to have significant effects on energy reduction. This paper describes a concept of hybrid system and propose a new type of hybrid system using radiational cooling with wind-induced cross ventilation. Moreover, a radiational cooling system is compared with an all-air cooling system. The characteristics of the indoor environment will be examined through CFD (Computational Fluid Dynamics) simulation, which is coupled with a radiation heat transfer simulation and with HVAC control in which the PMV value for the human model in the center of the room is controlled to attain the target value.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.519-521
• /
• 1994

In this paper, the welding machine with high-frequency inverter is described, which can save energy more than conventional ones with low efficiency. Although for part of welding machine of special type such as MIG, TIG, products were developed by inverter, but it is poor that applied to ordinary ac arc welding machine. Difference between conventional AC arc welding machine and the proposed welding machine is investigated econimically and constructionally. Untill now, kinds of welding machine and its characteristics were also described. The comparison of the proposed welding machine and the conventional is presented in the way of output control.

• Proceedings of the Korean Information Science Society Conference
• /
• 2012.06d
• /
• pp.378-380
• /
• 2012

본 논문은 사용하지 않는 공간에서 낭비되는 전기 에너지량을 감소시키기 위한 사용자 위치기반의 대기전력 제어시스템을 설계 및 구현한다. 사용자의 위치파악을 위해 주거시설의 해당 영역을 3개의 구역으로 분리하고 각 구역에 2개의 PIR센서를 설치하여 입 출입 현황 및 재실인원을 점검하며, 재실여부와 가전제품의 대기모드 여부에 따라 ZigBee 무선통신을 이용해 전력센서를 차단 혹은 해제한다. 또한, 시스템을 검증하기 위해 전력센서로 수집한 전력량을 대기전력의 차단과 해제로 비교하여 에너지 절감률을 분석한다.