• Journal of Dairy Science and Biotechnology
• /
• v.21 no.2
• /
• pp.105-113
• /
• 2003

This study was carried out to investigate the addition of Pueraria derived isoflavone into milk by means of microencapsulation technique. The yield microencapsulation sensory attributes, and capsule stability of Pueraria derived isoflavone microcapsules in milk were measured during 12 days. Coating materials used was polyglycerol monostearate(PGMS. The encapsulation yield of Pueraria derived isoflavone was 72.5% with PGMS when the ratio of coating material to core material was 15:1. The rate of pueraria derived isoflavone release was 15, 20, and 25% when stored at 4, 20, and $30^{circ}C$ for 12 days in milk respectively. In sensory evaluation, beany flavor and color of microcapsuled Pueraria derived isoflavone added milk were significantly different from control and uncapsuled Pueraria derived isoflavone added milk, however, bitterness was not significantly different. In vitro study, microcapsules of pueraria derived isoflavone in simulated gastric fluid with the range of 3 to 6 pHs were released 3.0${\sim}$15.0%, however, the capsules in simulated intestinal fluid with pH 7 were released 95.7% for 40 min incubation time. In conclusion, this study provided that PGMS as coating materials was suitable for the microencapsulation of Pueraria derived isoflavone, and the capsule containing milk was not affected with sensory attribute.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.147-153
• /
• 2018

PLGA microcapsule particles encapsulating BSA aqueous solutions were prepared using a water-in-oil-in-water emulsion method. The morphology, particle size, BSA encapsulating efficiency, and in-vitro release test were also studied using the microcapsule particles. In the outer aqueous phase, an emulsifier, e.g., PVA, was replaced with metal salts for surface solidification. Scanning electron microscopy (SEM) showed that the microcapsule particles had smooth surfaces and were between $1{\mu}m$ and $7{\mu}m$ in size. The microcapsule particle morphology was affected directly by the ratio between the polymer solution and inner aqueous solution, and composition of the outer aqueous solution. The factors also partially affected the BSA encapsulation efficiencies and in-vitro release rates. All the microcapsule particles showed an initial burst release through the in-vitro release test. On the other hand, the particles also showed a relatively long release period. Metal salts could be good choices to replace the emulsifier to solidify the microcapsule particle surfaces.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.4
• /
• pp.1041-1051
• /
• 2020

The technology of microbubbles and nanobubbles originated in Japan and Europe is applicable to various applications and its effects are diverse, attracting attention not only from many researchers but also from industry experts. In particular, nanobubbles have the advantage that they can be applied to products in the form of liquids, such as cosmetics, from the study that they can exist for more than several months in water. In this study, it was carried out the production of nanobubbles using bubble encapsulation technique and the experiment of skin permeability enhancement of active substances in cosmetics using nanobubble techniquethree. Nanobubbles were confirmed to affect the skin permeability increase of active substances, and up to 250% increase in skin permeability compared to non-bubbles-free materials(Caffeic acid, at 8 hour). It is expected that research results and industrial ripple effects can be expected not only in the cosmetic field, but also in fields applicable to the improvement of permeability by nanobubble techniques, such as areas related to drug delivery system.

• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.78-87
• /
• 2015

With aiming to prepare microcapsules having a particle size of $30-50{\mu}m$, thermally expandable capsules with relatively uniform particle sizes consisting of a n-octane/poly(acrylonitrile-co-methyl methacrylate) core/shell structure were synthesized using SPG membrane emulsification and suspension polymerization. Four steric stabilizers and five crosslinking agents were employed. When poly(vinyl alcohol) as a stabilizer was used, the prepared capsules showed a smooth and regular morphology and the liquid hydrocarbon (n-octane) was well encapsulated in the core. When 1,4-butnaediol methacrylate (BDDMA) was used as a crosslinker, the uniform capsules with the average diameter of $36.8{\mu}m$ were synthesized. The capsules prepared with 0.05 mol% BDDMA showed the best encapsulation efficiency.

• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.20-24
• /
• 2007

The preservation of biological activity of protein drugs in formulation is still a major challenge for successful drug delivery. Lipase was encapsulated in poly (D,L-lactide- co-glycolide) PLGA nano-particles using a w/o/w solvent evaporation technique. The lipase-containing PLGA/poly (vinyl alcohol) (PVA) nanoparticles were characterized with regard to morphology, size, size distribution, lipase-loading efficiency, in vitro lipase release, and stability of lipase activity. The size of nanoparticles increased as polymer concentration was increased. The size of particles was not significantly affected by the PVA concentration; on the other hand, the particle size distribution was the narrowest when 4% of PVA was used. In optimum conditions, we possessed nanoparticles that characterized 72.5% of encapsulation efficiency, $198.3{\pm}13.8 nm$ size diameter. During the initial burst phase, the in vitro release rate was very fast, reaching 83% within 12 days. Until days 6, enzyme activity increased as the amount of lipase released was increased.

• Food Science and Biotechnology
• /
• v.14 no.5
• /
• pp.566-571
• /
• 2005

Process of screw-pumping system (SPS) was optimized for mass production of encapsulated bifidus. SPS entrapment device was composed of feeding component, with optimized nozzle size and length of 18G (0.91 cm) and 4 mm, respectively, screw pump, and 37-multi-nozzle. Screw component had five wing turns [radius (r)=26 to 15 mm] from top to bottom of axis at 78-degree angle from middle of the screw, and two wings were positioned at screw edge to push materials toward nozzle. For nozzle component, 37 nozzles were attached to 20-mm round plate. Air compressor was attached to SPS to increase productivity of encapsulated bifidus. This system could be operated with highly viscous (more than 300 cp) materials, and productivity was higher than $1128\;{\pm}\;30\;beads/min$. Viability of encapsulated bifidus was $5.45\;{\times}\;10^8\;cfu$/bead, which is superior to that of encapsulated bifidus produced by other methods ($2.51{\times}10^8\;cfu$/bead). Average diameter of produced beads was $2.048\;{\pm}\;0.003\;mm$. Survival rate of SPS-produced encapsulated bifidus was 90% for Simulator of the Human Intestinal Microbial Ecosystem test and 88% in fermented milk (for 14 days). These results show SPS is effective for use in development of economical system for mass production of viable encapsulated bifidus.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.157-164
• /
• 2007

Microencapsulation of cells within microfluidic devices enables explicit control of the membrane thickness or cell density, resulting in improved viability of the transplanted cells within an aggressive immune system. In this study, living cells (3T3 and L929 fibroblast cells) are encapsulated within a semi-permeable membrane (calcium crosslinked alginate gel) in two different device designs, a flow focusing and a core-annular flow focusing geometry. These two device designs produce a bead and a long microfibre, respectively. For the alginate bead, an alginate aqueous solution incorporating cells flows through a flow focusing channel and an alginate droplet is formed from the balance of interfacial forces and viscous drag forces resulting from the continuous (oil) phase flowing past the alginate solution. It immediately reacts with an adjacent $CaCl_2$ drop that is extruded into the main flow channel by another flow focusing channel downstream of the site of alginate drop creation. Depending on the flow conditions, monodisperse microbeads of sizes ranging from $50-200\;{\mu}m$ can be produced. In the case of the microfibre, the alginate solution with cells is extruded into a continuous phase of $CaCl_2$ solution. The diameter of alginate fibres produced via this technique can be tightly controlled by changing both flow rates. Cell viability in both forms of alginate encapsulant was confirmed by a LIVE/DEAD cell assay for periods of up to 24 hours post encapsulation.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.636-641
• /
• 2012

In this study, we have investigated highly efficient nanoscale surface corrugated light emitting diodes (LEDs) for the enhancement of light extraction efficiency (LEE) of nitride semiconductor LEDs. Nanoscale indium tin oxide (ITO) surface corrugations are fabricated by using the conformal nanoimprint technique; it was possible to observe an enhancement of LEE for the ITO surface corrugated LEDs. By incorporating this novel method, we determined that the total output power of the surface corrugated LEDs were enhanced by 45.6% for patterned sapphire substrate LEDs and by 41.9% for flat c-plane substrate LEDs. The enhancement of LEE through nanoscale surface corrugations was studied using 3-dimensional Finite Different Time Domain (FDTD) calculation. From the FDTD calculations, we were able to separate the light extraction from the top and bottom sides of device. This process revealed that light extraction from the top and bottom sides of a device strongly depends on the substrate and the surface corrugation. We found that enhanced LEE could be understood through the mechanism of enhanced light transmission due to refractive index matching and the increase of light scattering from the corrugated surface. LEE calculations for the encapsulated LEDs devices also revealed that low LEE enhancement is expected after encapsulation due to the reduction of the refractive index contrast.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.2
• /
• pp.143-151
• /
• 2008

74% of Internet users use the UCC, and You Tube using firearms in a crime occurred. Internet crime occurred in the online, non-face transaction, anonymous, encapsulation. In this paper, we are studied a Network Forensic Way and a technique analyze an aspect criminal the Internet haying appeared at Internet UCC, and to chase. Study ID, IP back-tracking and position chase through corroborative facts collections of the UCC which used UCC search way study of the police and a public prosecutor and storage way and network forensic related to crimes of Internet UCC. Proof data encrypt, and store, and study through approach control and user authentication so that they are adopted to legal proof data through integrity verification after transmission and storages. This research via the Internet and criminal conspiracy to block the advance promotion, and for the criminal investigative agencies of the Internet will contribute to the advancement forensics research.

• Analytical Science and Technology
• /
• v.15 no.6
• /
• pp.540-549
• /
• 2002

The arrangement of encapsulated Ar atoms in the molecular-dimensioned cavities of fully dehydrated zeolite A of unit-cell composition $Cs_3Na_8HSi_{12}Al_{12}O_{48}$ ($Cs_3$-A) has been studied crystallographically to probe the confinement effect of guest species in microporous environment. Atoms of Ar were encapsulated in the cavities of $Cs_3$-A by treatment with 410 atm of Ar at $400^{\circ}C$ for two days, followed by cooling at room temperature. The crystal structure of $Cs_3Na_8H$-A(4Ar) ($P_e$ = 410 atm, $a=12.245(2){\AA}$, $R_1=0.0543$, and $R_2=0.0552$) has been determined by single crystal X-ray diffraction technique in the cubic space group $Pm\bar{3}m$ at 21 (1) $^{\circ}C$ and 1 atm. Encapsulated Ar atoms are distributed in three crystallographic distinct positions: 1.5 Ar atoms per unit cell opposite 6-rings, 1.5 opposite four-rings in the large cavity, and finally 1.0 in the sodalite-unit. The possible structures of argon clusters, such as $Ar_2$, $Ar_3$, and $Ar_4$, are proposed.