• Applied Biological Chemistry
• /
• v.13 no.2
• /
• pp.131-151
• /
• 1970

A new method of plastic film coating has been investigated to extend storage life of apples. The film coating was effected by dipping fresh apples in a plastic emulsion. The effect of plastic film coating on the preservation of freshness, respiratory activities and chemical components during storage, has been investigated on four leading varieties of apples. The results are summarized as follows: 1. The effect of film coating on storage life of apples was apparent, resulting in delay of after-ripening, shriveling, softening or physiological impediment as well as reducing consumption of reserve materials and waste fruits. 2. Change in the partial pressure of gas, i.e., increase in carbon dioxide and decrease in oxygen in apple tissue was resulted by the plastic film coating, suggesting that the film deposited on the fruit interfered with the diffusion of gases formed therein. 3. The effects of plastic film coating on the fruit storage varied with the type of plastic emulsions, coating temperature, varieties of apples and degree of fruit ripening. As regard to apple varieties, good results were obtained with PVA 217 for both American Summer Pearmain and Jonathan, and PVC 443 for McIntosh. 4. Reduction in the diminution rates of L-malic acid, ascorbic acid and soluble pectin etc. during storage of apples may account for the improved storage life of the fruits treated with plastic films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.66.2-66.2
• /
• 2011

A polymer-based multi-walled carbon nanotube (MWCNT) field emission device was fabricated from a composite dispersion of MWCNTs and waterborne polymethyl methacrylate (PMMA). The waterborne PMMA synthesized through the emulsion polymerization method was added to minimize the reagglomeration of dispersed MWCNTs with surfactants in water, and increase the adhesion between the and the substrate. The field emission properties of the fabricated device were optimized by adjusting the density of the emitter and the adhesion between the MWCNTs and the substrate. These were done by controlling the polymer concentration added to the MWCNT dispersion, as well as the amount of spray coating on the substrate. The results confirm the successful fabrication of a polymer-based MWCNT field emission device with a low field of 1.07 $V/{\mu}m$ and a good electric field enhancement factor of 2445. The device was fabricated by adding 0.8 mg/mL of polymer solution to the MWCNT dispersion and applying 20 cycles of spray coating. Application of this same MWCNT/polymer composite solution to a flexible polymer substrate also resulted in the successful fabrication of an electric field emission device with uniform emission and long time stability.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.12
• /
• pp.1770-1774
• /
• 2000

Extended use of porcine blood in food ingredients depends on the decolorization of red blood cell concentrates and the modification of its functional properties. The purpose of this study is to compare the relative effect of cation ion exchanger for decolorization of porcine red blood globin. The globin extract is freeze-dried for determination of various functional properties, such as solubility, emulsion capability and foaming ability. Since the isoelectric point of blood globin is located at pH 6.8, which is the neutral pH ranges (6-8), so its functionalities are inferior around these pHs. This weakness has been the main reason, which limit the extended use of blood globin in food industry. Acetylation and succinylation of blood globin can be an alternative way to improve its functionalities. These results may provide new information to understand the decolorization mode by cation ion exchanger for the blood globin. With chemical, the functionalities of blood globin could be obviously improved. The above findings could enable food industry to extend the use of blood globin as a food ingredient.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.22-28
• /
• 2015

A compression ignition type of diesel engine makes fuel efficiency better and $CO_2$ in the exhaust gas lower. Also it is suitable to apply alternative fuels(blended fuel) to the engine. The objective of this study is the emissions reduction of diesel engine with EF(Emulsified fuel). The emulsified fuel consists of diesel and peroxide($H_2O_2$) and Soot reduction without worsening of NOx emissions can be achieved by using thermal decomposition of the peroxide, i.e. the chemical effect of the OH radical in actual engine. For manufacturing emulsified fuel, a surfactant which is comprised of span 80 and tween 80 mixed as 9:1, was mixed with a fixed with 3% of the total volume in the emulsion fuel. In addition, considering the mixing ratio of the surfactant, the mixing ratio of $H_2O_2$ in the emulsified fuel was set as EF0, EF2, EF12, EF22, EF32, and EF42, respectively. Consequently, this study aims to obtain the optimization of fuel design(mixing) for the emulsified fuel applying to the diesel engine.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1756-1762
• /
• 2002

To effectively meet current regulations on the exhaust emissions of diesel engine required to control the deterioration of air pollution in the whole world, this study is to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in IDI diesel engine. A method fur supplying water through the air intake system to reduce the exhaust emissions has been considered with other methods such as water introduction in the form of water-in-fuel emulsion or water injection directly into the combustion chamber, but it has not been studied about the effects of water on the combustion concepts and the characteristics of exhaust emissions in detail until now. In this study, the formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water play a role as a heat sink during evaporating in the combustion chamber, but the smoke was slightly increased by increasing water amount.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.1
• /
• pp.39-43
• /
• 2008

Cyclosporin A (CyA), a potent immunosuppressive drug used in allogeneic transplants and autoimmune disease, is a typical water-insoluble drug. Recently, nanoparticle carriers were investigated to improve the intestinal absorption of drugs. In this study, CyA-loaded nanostructured lipid carriers (NLCs) were prepared from a hot o/w emulsion using the high pressure homogenization method. The NLCs were consisted of cationic lipids, solid lipids, liquid lipids (oils), surfactant and stabilizer. Encapsulation efficiency of CyA in NLCs was approximately 71%. The average particle size and zeta potential of NLCs were below 250 nm and above +40 mV, respectively. The morphology of NLCs was confirmed by transmission electron microscopy (TEM) analysis. Compared to the CyA powder, higher in vitro release of CyA from NLCs was observed after burst release within 30 min. Thus, CyA-loaded NLCs could be applied not only for parenteral route but also for gastrointestinal administration, which needs further investigation.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.128-135
• /
• 2003

To decrease environmental damage, the development of environmental friendly fluids provides attractive alternative to the conventional fluids. In this study, the effects of harmful ingredients (Cl, S) contained in the fluids that used in grinding and cutting processes to influence on the nasal cavities of the white rats were measured indirectly. Also, the level of the environmental influence in workshops was graded through analyzing the concentration and chemical ingredients of flying-dust, which generated from the friction and combustion in the cutting process, that for analyzing how harmful the influence of particles to workers then it could be used as the basic data for improving the environment. To improve the conventional machining fluid, which can be harmful on worker's bodies and the environment, the environmental friendly machining method was suggested through analyzing each lubrication properties of vegetable fluid and used-edible oil as alternative fluid. As a result, it was known that an emulsion type fluid might be the main cause leading to some respiratory ailments. Also this paper presents the possibility to use vegetable fluid and used-edible oil as the alternative of cutting fluids.

• Journal of Pharmaceutical Investigation
• /
• v.17 no.1
• /
• pp.38-40
• /
• 1987

To optimize the preparation condition of oil in water microemulsion rheological method was used. The viscosity-temperature curve of refined soybean oil was recorded and from this result microemulsion was prepared at various temperatures and evaluated by Coulter counter during 3 weeks. The difference in rheograms of crude emulsion and the microemulsion varying the number of passes in the homogenizer was also examined. From above experiments following conclusions were obtained. 1) Through all the process, temperature was an important factor and the optimum was $60-80^{\circ}C$. 2) By first pass in the homogenizer, most oil droplets were finely dispersed. 3) In the homogenizing step the higher pressure results in the finer dispersion but as the pressure goes up, the differential efficiency of dispersion was decreased.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.22 no.2
• /
• pp.52-69
• /
• 1996

Nano-Sized TiO$_2$ particles with diameter between 2 and 5 nm are synthesized in Water/Triton X-100/n-Hexane microemulsion. Particles show the amorphous structure and partially hydroxide form. The optical absorbance of particles appears at 250nm and band edge at 340nm. Gold metal is deposited on the surface of TiO$_2$ particles by reduction reaction of Au(III) ion with sodium hypophosphite. The size of gold-deposited particles is 20nm, and the optical absorbance appears at 270nm and at 550nm. So particles show the red color. The dense precipitation is formed by aggregation in the TiO$_2$ nano-sized particles of about 5nm size. But the bulky precipitation is formed by agglomeration phenomena in the gold-deposited particles of 20nm size. And also gold-deposited particles is easily dispersed by being re-dispersed in PEG/Water solution. This study has compared those things measuring the SPF characteristics of the cosmetics made of the synthesized particles. If the particle size is controlled appropriately, then the SPF value will be higher, or more colorless cosmetics will be made.

• YAKHAK HOEJI
• /
• v.41 no.1
• /
• pp.30-37
• /
• 1997

In order to formulate a controlled release system for oral drug delivery, the microcapsules were prepared in w/o emulsion containing cefaclor as a water-soluble model drug by th e method of interfacial polycondensation. Gelatin wis selected as a suitable polymer for interfacial polycondensation. Gelatin solution containing drug was emulsified in an organic phase under mechanical stirring. After emulsification, terephthaloyl chloride was added as cross linking agent, followed by mechanical stirring, washing and drying. Physical characteristics of microcapsules were investigated by optical microscopy, scanning electron microscopy and particle size analysis. Mean particle sizes of gelatin microcapsules were, in the range, of about 20~50 ${\mu}$m. The microcapsules were in good apperance with spherical shapes before washing, but were destroyed partially after washing and drying, even though some microcapsules were still maintained in their shapes. Contents of cefaclor in the microcapsules were calculated by UV spectrophotometry after 3 days extraction with pH 4 carbonate buffer solution. The effects of cross linking time. pH. concentration of cross-linking agent, and temperature on drug release kinetics have been discussed extensively.