• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1131-1136
• /
• 2011

본 연구는 자동차용 CNG 연료탱크의 파열시험시 발생하는 음향방출변수의 분석에 관한 내용이다. 연료탱크의 복합재료 중앙부 표면에 150kHz 공진형 AE센서를 부착하여 파열시험시 발생하는 음향방출 신호를 획득하고, 가압유지시간 동안의 hit, amplitude, count, duration, risetime, signal strength 등과 같은 음향방출 변수들을 분석하였다. 음향방출 변수 중 total count, total signal strength가 연료탱크 손상정도를 평가하는데 유용한 변수임을 알 수 있었다.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.203-209
• /
• 2018

Reliable estimation of compressive as well as tensile in-situ stresses is critical in the design and analysis of underground structures and openings in rocks. Kaiser effect technique, which uses acoustic emission from rock specimens under cyclic load, is well established for the estimation of in-situ compressive stresses. This paper investigates the Kaiser effect on marble specimens under cyclic uniaxial compressive as well as cyclic uniaxial tensile conditions. The tensile behavior was studied by means of Brazilian tests. Each specimen was tested by applying the load in four loading cycles having magnitudes of 40%, 60%, 80% and 100% of the peak stress. The experimental results confirm the presence of Kaiser effect in marble specimens under both compressive and tensile loading conditions. Kaiser effect was found to be more dominant in the first two loading cycles and started disappearing as the applied stress approached the peak stress, where felicity effect became dominant instead. This behavior was observed to be consistent under both compressive and tensile loading conditions and can be applied for the estimation of in-situ rock stresses as a function of peak rock stress. At a micromechanical level, Kaiser effect is evident when the pre-existing stress is smaller than the crack damage stress and ambiguous when pre-existing stress exceeds the crack damage stress. Upon reaching the crack damage stress, the cracks begin to propagate and coalesce in an unstable manner. Hence acoustic emission observations through Kaiser effect analysis can help to estimate the crack damage stresses reliably thereby improving the efficiency of design parameters.

• Tribology and Lubricants
• /
• 제35권5호
• /
• pp.317-322
• /
• 2019

In spite of progress in tribological research, machine component failure due to friction and wear has been reported frequently. This failure may lead to secondary damage that can cause huge expense for maintenance and repair. To prevent economic loss, it is important to detect and predict the initial failure point. In this sense, various researchers have been tried to develop Condition Monitoring (CM) method using Acoustic Emission (AE) generated while the materials undergo failure. In this study, effect of particles on friction and wear was investigated using the pin-on-plate friction test and AE signal was recorded with a band-width type AE sensor. The experiments were performed in dry and lubricant conditions using steel and glass as specimens. After the experiment, 3D laser microscope image was captured to evaluate the wear behavior quantitatively. The AE signal was analyzed in time-domain and frequency-domain. The amplitude was compared with the frictional results. The results of this study showed that particle generation accelerate wear, generate high magnitude AE signal and change the frequency characteristics of the signal. Also, lubricant condition test results showed low coefficient of friction, low wear rate, and low magnitude of AE signal compared to the dry condition. It is expected that the results of this study will aid in better assessment of wear in CM technology

• Smart Structures and Systems
• /
• 제16권1호
• /
• pp.67-79
• /
• 2015

Acoustic emission analysis is an effective technique for monitoring the evolution of damage in a structure. An experimental analysis on a set of reinforced concrete beams under flexural loading was carried out. A mixed AE analysis method which used both parameter-based and signal-based techniques was presented to characterize and identify different failure mechanisms of damage, where the signal-based analysis was performed by using the Hilbert-Huang transform. The maximum instantaneous energy of typical damage events and the corresponding frequency characteristics were established, which provided a quantitative assessment of reinforced concrete beam using AE technique. In the bending tests, a "pitch-catch" system was mounted on a steel bar to assess bonding state of the steel bar in concrete. To better understand the AE behavior of bond-slip damage between steel bar and concrete, a special bond-slip test called pullout test was also performed. The results provided the basis of quantitative AE to identify both failure mechanisms and level of damages of civil engineering structures.

• 한국분무공학회지
• /
• 제24권1호
• /
• pp.21-26
• /
• 2019

In Korea, Medium-duty trucks are classified into GVW (Gross Vehicle Weight) 3.5~10tons. MDTs are mostly used for logistics or delivery between regions. There have been studied on diesel fuel vehicles for SUVs(Sports Utility Vehicle) or light-duty trucks. But MDTs have been not studied. Therefore, this study have been used MDTs for characteristic exhaust emission. Test was carried out using the certification test mode (NEDC, New European Driving cycle) and the NIER mode in chassis dynamometer of the MDTs. And emission gas was analyzed for PN (Particulate Number), PN size distribution and aldehydes, VOCs (Volatile Organic Compounds), PAHs (Polycyclic Aromatic Hydrocarbons). This paper concluded that EURO-IV trucks produced more MSATs than EURO V trucks. Depending on the engine temperature, more MSATs were generated in cold temperature than in the hot start operation. However, the driving speed, the opposite results was obtained.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.677-682
• /
• 1998

Concrete is an inhomogeneous material consisting of larger aggregates and sand embedded in a cement paste matrix. In this study, an acoustic emission technique has been used to clarify the microscope failure mechanisms of concrete under three point bending test. AE source location has also been done to monitor the activities of internal damage and the progress of microscopic failure path during the loading. The relationship between AE characteristic and microscopic and microscopic failure mechanism is discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.845-850
• /
• 2003

Noise caused by water installations may lead to annoyance in adjacent rooms, for example in dwellings. hospitals and hotels. This part of standard describes a method of measurement allowing comparable results to be obtained in laboratory measurements. The test conditions described herein constitute the standard reference conditions essential for comparisons between laboratories.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.243-247
• /
• 2001

As a means to reduce stiction in the landing zone padded sliders can be used. In this work the performance of padded slider was investigated using a commercial spin stand. The friction and acoustic emission signals were measured during the experiment. It is shown that padded slider show superior friction and AE characteristics. However, the wear properties of the pads should be further Improved.

• 한국응용과학기술학회지
• /
• 제35권4호
• /
• pp.1108-1119
• /
• 2018

대기오염에 대한 관심은 국내 외에서 점진적으로 상승하고 있으며, 자동차 및 연료 연구자들은 청정(친환경 대체연료) 연료와 연료품질 향상 등을 위해 새로운 엔진 설계, 혁신적인 후 처리 시스템 등의 많은 접근을 통하여 차량 배출가스와 온실가스를 감소시키려고 노력하고 있다. 이러한 연구들은 주로 차량의 배출가스 (규제 및 미규제물질, PM 입자 배출 등)와 온실가스의 두 가지 이슈로 진행되고 있다. 자동차의 배출가스는 환경오염과 인체에 악영향을 주는 많은 문제를 일으키고 있다. 이러한 배출가스를 줄이기 위하여 각국에서는 배출가스 시험모드를 새로 만들어 규제하고 있다. 2007 년부터 UN ECE의 WP.29 포럼에서 배출가스 인증을 위한 전 세계의 조화된 light-duty 차량 시험 절차 (WLTP)가 개발되었다. 이 시험 절차는 유럽과 동시에 국내 light-duty 디젤 차량에도 적용되어졌다. Light-duty 차량의 대기오염 물질 배출량은 거리 당 무게로 규제되어 있어 주행주기가 결과에 영향을 미칠 수 있다. 차량의 배출가스는 주행 및 환경조건, 주행습관 등에 따라 크게 달라진다. 극단적인 외기온도는 배출가스를 증가시키는데, 이것은 더 많은 연료가 실내를 가열하거나 냉각해야하기 때문이다. 또한 높은 주행속도는 증가된 항력을 극복하기 위해 필요한 에너지로 인해 배출가스 량을 증가시킨다. 일반적으로 상승하는 차량속도와 비교할 때, 급격한 차량가속도도 배출가스를 증가시킨다. 부가적인 장치 (에어컨 또는 히터)와 도로경사 또한 배출가스를 증가시킨다. 본 연구에서는 3대의 light-duty 차량을 가지고 light-duty 차량의 배출가스 규제에 사용되는 WLTP, NEDC 및 FTP-75로 시험을 하였으며, 배출가스가 다른 주행 사이클에 의해 얼마나 많은 영향을 받을 수 있는지를 측정하였다. 배출 가스는 통계적으로 의미있는 차이를 보이지 않았다. 최대 배출 가스는 주로 냉각 된 엔진 조건에 의해 야기되는 WLTP의 저속 단계에서 발견된다. 냉각 된 엔진 상태에서 배출가스의 양은 시험 차량과 크게 다르다. 이는 WLTP 구동 사이클에 대처하기 위해 다른 기술적 솔루션이 필요하다는 것을 의미한다.

• 한국입자에어로졸학회지
• /
• 제13권1호
• /
• pp.17-23
• /
• 2017

In this study, the test results obtained from the performance tests for CA (Korea Association of Cleaning Air) certificated air cleaners which had been commercially available in Korea from 2003 to 2015 were analyzed. Among the test parameters such as flow rate, particle collection efficiency, clean air delivery rate (CADR), ozone emission, odor removal efficiency and noise level, noise level and CADR were correlated with flow rates. Collection and odor removal efficiencies were 20% higher than the limit of the CA certification. The ozone emissions from the air cleaners were negligible because all the air cleaners were equipped with only HEPA filters, not electrostatic precipitation method which produces ozone.