• 한국터널지하공간학회 논문집
• /
• 제13권1호
• /
• pp.71-82
• /
• 2011

본 논문에서는 강섬유 형상에 따른 인발력 거동에 대한 연구를 수행하였다. 최적의 강섬유 형상을 도출하기 위하여 매입 된 강섬유가 이루는 각도와 길이를 변화시켜가며 인발실험을 시행하였다. 또한 인발실험 결과를 모사하기 위해 수치 해석을 수행하였다. 그 결과 강섬유 형상에 있어서 hook 각도와 설치각도 클수록 인발력이 뛰어나며, 특히 강섬유의 길이가 짧아짐에 따라 인발력도 뛰어난 것으로 판단되어졌다.

• Steel and Composite Structures
• /
• 제22권6호
• /
• pp.1239-1259
• /
• 2016

The modified couple stress-based third-order shear deformation theory is presented for sigmoid functionally graded materials (S-FGM) plates. The advantage of the modified couple stress theory is the involvement of only one material length scale parameter which causes to create symmetric couple stress tensor and to use it more easily. Analytical solution for dynamic instability analysis of S-FGM plates on elastic medium is investigated. The present models contain two-constituent material variation through the plate thickness. The equations of motion are derived from Hamilton's energy principle. The governing equations are then written in the form of Mathieu-Hill equations and then Bolotin's method is employed to determine the instability regions. The boundaries of the instability regions are represented in the dynamic load and excitation frequency plane. It is assumed that the elastic medium is modeled as Pasternak elastic medium. The effects of static and dynamic load, power law index, material length scale parameter, side-to-thickness ratio, and elastic medium parameter have been discussed. The width of the instability region for an S-FGM plate decreases with the decrease of material length scale parameter. The study is relevant to the dynamic simulation of micro structures embedded in elastic medium subjected to intense compression and tension.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.865-871
• /
• 2003

This paper presents the test results of 24 beam-end specimens to investigate the effect of concrete strength and cover thickness on the development resistance capacity in tensile lap splice length regions. The results showed that as higher strength concrete was employed, nor only development resistance capacity was influenced by cover thickness, but also more sufficient safety factor reserved shorter than the lap splice length provision in current design code. From experimental research results, high-strength concrete development length was not inverse ratio of ($\sqrt{f_{ck}}$) but directly inverse of $f_{ck}$, and it is also said that there is a certain limit length of the embedded steel over which the assumption of uniform bond stress distribution is valid specially for high-strength concrete not having a same embed length such as normal-strength concrete in current design criteria hypothesis.

• 한국멀티미디어학회논문지
• /
• 제2권2호
• /
• pp.155-165
• /
• 1999

암호화(encryption)된 정보는 랜멈한 형태이기 때문에 공격자에 의해 기밀 정보가 누출될 위협이 있다. 한편, 화상 심충암호(image steganography)는 화상 내에 기밀 정보를 몰래 숨겨서 전송하는 것으로 제3자는 기밀 정보의 폰재 사실을 알 수 없기 때문에 공격의 위협을 줄일 수 있게 된다. 화상 심충암호에서 기밀 정보는 잡음의 형태로 화상의 화소값을 변경하여 숨기게 된다 이와 같이 농담화상(gray image)에 기밀 정보 를 숨기는 경우에는 잡음으로 인한 화질 열화를 초래한다. 따라서, 농담화상에 디더링(dithering)을 수행하는 과정에서 기밀 정보를 숨기는 방식이 고안되었다 오차 확산법을 이용한 기존의 방식은 고정된 간격마다 기밀 정보를 합성함에 따라 일정한 패턴이 생기는 문제점이 있다 이러한 문제를 해결하고 기존의 방법을 향상시키기 위하여 본 논문에서는 런 길이(run length)를 이용하여 변환점에 기밀 정보를 합성하거나 원래의 디더값과 오차가 가장 적은 위치에 기밀 정보를 합성하는 새로운 방법을 제안하고, 그 성능을 컴퓨터 시율레이 션올 통하여 평가하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.301-304
• /
• 2008

본 연구에서는 싱글 플레이트 전단접합에 앵글을 접합한 새로운 방식의 철골 커플링보를 개발하여 여러 가지 구조적 성능을 평가하고자 한다. 주요 변수는 앵글유무, 콘크리트 보강 유무, 매립길이, 결손단면이다. 실험은 커플링 보의 가운데 지점을 2,000kN Actuator를 이용하여 횡방향 반복가력을 가하여 구조물의 전체적인 거동을 알아본다. 실험결과 싱글 플레이트 전단 접합부로 이루어진 실험체보다 앵글을 접합한 실험체가 강도, 변형능력, 강성, 에너지 소산 능력 등 전반적인 구조적 성능이 훨씬 우수한 것으로 나타났다. 매립된 철골보 주위에 전단철근을 보강하지 않은 경우 PC벽체의 조기 지압파괴로 인해 그 성능이 현저히 떨어지는 것으로 나타났다. 그러나 전단철근이 배근이 된 경우 철골 커플링 보의 전단 항복이 발생할 때까지 PC벽체의 파괴가 충분히 지연되는 것으로 나타났다. 앵글이 접합된 경우 매립길이가 작아도 그 성능이 떨어지지 않았다. 결손 단면이 있을 경우 강도는 작게 나타났으나 접합부 전단 강도보다 훨씬 작도록 설계된 관계로 PC벽체의 파괴가 발생하기 전에 충분히 전단 거동을 통해 우수한 성능을 발휘하였다. 이러한 결과는 시공성과 경제성 향상을 위해 앵글을 접합한 철골 커플링 보 방식이 매우 유용할 것으로 사료된다.

• Advances in concrete construction
• /
• 제14권5호
• /
• pp.299-307
• /
• 2022

Cement-based matrixes have low tensile strength and negligible ductility. Adding fibres to these matrixes will improve their mechanical properties and make these composites suitable for structural applications. Post-cracking tensile strength of steel fibers-reinforced cementitious composite materials is directly related to the number of transverse fibers passing through the crack width and the pulling-out behavior of each of the fibers. Therefore, the exact recognition of the pullout behavior of single fibers is necessary to understand the uniaxial tensile and bending behavior of steel fiber-reinforced concrete. In this paper, an experimental study has been carried out on the pullout behavior of 3D (steel fibers with totally two hooks at both ends), 4D (steel fibers with a total of four hooks at both ends), and 5D (steel fibers with totally six hooks at both ends) in which the fibers have been located either perpendicular to the crack width or in an inclined manner. The pullout behavior of the mentioned steel fibers at an inclination angle of 0, 15, 30, 45, and 60 degrees and with embedded lengths of 10, 15, 20, 25, and 30 millimetres is studied in order to explore the simultaneous effect of the inclination angle of the fibers relative to the alongside loading and the embedded length of fibers on the pullout response in each case, including the maximal pullout force, the slip of the maximum point of pullout force, pullout energy, fiber rupture, and concrete matrix spalling. The results showed that the maximum pullout energy in 3D, 4D, and 5D steel fibers with different embedded lengths occurs at 0 to 30° inclination angles. In 5D fibers, maximum pullout energy occurs at a 30° angle with a 25 mm embedded length.

• Geomechanics and Engineering
• /
• 제37권4호
• /
• pp.383-393
• /
• 2024

Monopile foundations of offshore wind turbines embedded in soft clay are subjected to the long-term cyclic lateral loads induced by winds, currents, and waves, the vibration of monopile leads to the accumulation of pore pressure and cyclic strains in the soil in its vicinity, which poses a threat to the safety operation of monopile. The researchers mainly focused on the hysteretic stress-strain relationship of soft clay and kinds of stiffness degradation models have been adopted, which may consume considerable computing resources and is not applicable for the long-term bearing performance analysis of monopile. In this study, a modified cyclic stiffness degradation model considering the effect of plastic strain and pore pressure change has been proposed and validated by comparing with the triaxial test results. Subsequently, the effects of cyclic load ratio, pile aspect ratio, number of load cycles, and length to embedded depth ratio on the accumulated rotation angle and pore pressure are presented. The results indicate the number of load cycles can significantly affect the accumulated rotation angle of monopile, whereas the accumulated pore pressure distribution along the pile merely changes with pile diameter, embedded length, and the number of load cycles, the stiffness of monopile can be significantly weakened by decreasing the embedded depth ratio L/H of monopile. The stiffness degradation of soil is more significant in the passive earth pressure zone, in which soil liquefaction is likely to occur. Furthermore, the suitability of the "accumulated rotation angle" and "accumulated pore pressure" design criteria for determining the required cyclic load ratio are discussed.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.21-24
• /
• 2005

Three dimensional circular braided Glass/Aramid hybrid fabric/epoxy resin composite was fabricated. FBG sensor was embedded along the braid yam in order to monitor the internal dimensional changes of the 3-D braid composite. The amount of cure and thermal shrinkage of epoxy resin was also determined using FBG sensor system. FBG sensors with different grating length were embedded and their response were compared. The thermo-optic coefficient of FBG sensor was measured by several preliminary experiments. The internal strain that measured by FBG sensor and electric strain gauge was compared during compressive test. The released residual strain of the fabricated tubular composite was estimated using cutting method. The internal strain of the composite was estimated using FBG sensor system, and the result was compared with the value from electric strain gauge. It was found that FBG sensor system is a very useful technique to investigate inside region of complicated structure.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.274-277
• /
• 2008

Pohang Wind Energy Research Center (PoWER-C) is developing a 3 MW Radial Flux Permanent Magnet (RFPM) Synchronous Generator for offshore Wind Energy Converter (WEC). The blade rotor rpm is 15.7 and the gear ratio is set to be 92.93. The nominal generator rpm at the rated load is about 1459. Baseline design with surface mounted PM magnets are completed. However, there is some concern about the excessive eddy current heating in the magnets. To alleviate this problem, another design with embedded magnet is going on. With embedded magnets, the generator length should be increased to compensate the increased flux leakage. But the field fluctuation in the magnets due to the slots are greatly reduced. This means less eddy currents and lower magnet operating temperature. In this report, engineering efforts for embedded rotor is presented.

• Computers and Concrete
• /
• 제9권3호
• /
• pp.171-178
• /
• 2012

This paper presents numerical studies of stiff fiber pullout behaviors of fiber reinforced cementitious composites based on a progressive damage model. The ongoing debonding process is simulated. Interfacial stress distribution for different load levels is analyzed. A parametric study, including bond strength and the homogeneity index on the pullout behaviors is carried out. The numerical results indicate that the bond stress decreases gradually from loaded end to embedded end along fiber-cement interface. The debonding initially starts from loaded end and propagates to embedded end as load increasing. The embedded length and bond strength affect the load-loaded end displacement curves significantly. The numerical results have a general agreement with the experimental investigation.