• ETRI Journal
• /
• v.44 no.5
• /
• pp.859-874
• /
• 2022

This paper presents a low-power and lightweight human body communication (HBC) receiver with an embedded dummy electrode for improved signal acquisition. The clock data recovery (CDR) circuit in the receiver operates with a low supply voltage and utilizes a clock phase inversion scheme. The receiver is equipped with a main electrode and dummy electrode that strengthen the capacitive-coupled signal at the receiver frontend. The receiver CDR circuit exploits a clock inversion scheme to allow 0.9-V operation while achieving a shorter lock time than at 3.3-V operation. In experiments, a receiver chip fabricated using 130-nm complementary metal-oxide-semiconductor technology was demonstrated to successfully receive the transmitted signal when the transmitter and receiver are placed separately on each hand of the user while consuming only 4.98 mW at a 0.9-V supply voltage.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.8
• /
• pp.61-67
• /
• 2010

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite-Difference Time-Domain (FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency-dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• ETRI Journal
• /
• v.25 no.5
• /
• pp.337-344
• /
• 2003

In this paper, we introduce a fully synthesizable 32-bit embedded microprocessor core called the AE32000B. The AE32000B core is based on the extendable instruction set computer architecture, so it has high code density and a low memory access rate. In order to improve the performance of the core, we developed and adopted various design options, including the load extension register instruction (LERI) folding unit, a high performance multiply and accumulate (MAC) unit, various DSP units, and an efficient coprocessor interface. The instructions per cycle count of the Dhrystone 2.1 benchmark for the designed core is about 0.86. We verified the synthesizability and the area and time performances of our design using two CMOS standard cell libraries: a 0.35-${\mu}m$ library and a 0.18-${\mu}m$ library. With the 0.35-${\mu}m$ library, the core can be synthesized with about 47,000 gates and operate at 70 MHz or higher, while it can be synthesized with about 53,000 gates and operate at 120 MHz or higher with the 0.18-${\mu}m$ library.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.105-109
• /
• 2005

A compact antenna switch module for GSM/DCS dual band applications based on multilayer low temperature co-fired ceramic (LTCC) substrate is presented. Its size is $4.5{\times}3.2{\times}0.8 mm^3$ and insertion loss is lower than 1.0 dB at Rx mode and 1.2 dB at Tx mode. To verify the stability of the developed module to the process window, each block that is diplexer, LPF's and bias circuit is measured by probing method in the variation with the thickness of ceramic layer and the correlation between each block is quantified by calculating the VSWR In the mean while, two types of bias circuits -lumped and distributed - are compared. The measurement of each block and the calculation of VSWR give good information on the behavior of full module. The reaction of diplexer to the thickness is similar to those of LPF's and bias circuit, which means good relative matching and low value of VSWR, so total insertion loss is maintained in quite wide range of the thickness of ceramic layer at both band. And lumped type bias circuit has smaller insertion itself and better correspondence with other circuit than distributed stripline structure. Evaluated ceramic module adopting lumped type bias circuit has low insertion loss and wider stability region of thickness over than 6um and this can be suitable for the mass production. Stability characterization by probing method can be applied widely to the development of ceramic modules with embedded passives in them.

• Korean Journal of Materials Research
• /
• v.28 no.1
• /
• pp.32-37
• /
• 2018

We report on the efficient detection of NO gas by an all-oxide semiconductor p-n heterojunction diode structure comprised of n-type zinc oxide (ZnO) nanorods embedded in p-type copper oxide (CuO) thin film. The CuO thin film/ZnO nanorod heterostructure was fabricated by directly sputtering CuO thin film onto a vertically aligned ZnO nanorod array synthesized via a hydrothemal method. The transport behavior and NO gas sensing properties of the fabricated CuO thin film/ZnO nanorod heterostructure were charcterized and revealed that the oxide semiconductor heterojunction exhibited a definite rectifying diode-like behavior at various temperatures ranging from room temperature to $250^{\circ}C$. The NO gas sensing experiment indicated that the CuO thin film/ZnO nanorod heterostructure had a good sensing performance for the efficient detection of NO gas in the range of 2-14 ppm under the conditions of an applied bias of 2 V and a comparatively low operating temperature of $150^{\circ}C$. The NO gas sensing process in the CuO/ZnO p-n heterostructure is discussed in terms of the electronic band structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.21-21
• /
• 2010

(Ba,Sr)$TiO_3$ (BST) thin film with a perovskite structure has potential for the practical application in various functional devices such as nonvolatile-memory components, capacitor, gate insulator of thin-film transistors, and electro-optic devices for display. Normally, the BST thin films derived from sol-gel and sputtering are amorphous or partially crystalline when processed below $600^{\circ}C$. For the purpose of integrating BST thin film directly into a Si-based read-out integrated circuit (ROIC), it is necessary to process the BST film below $400^{\circ}C$. The microstructural and electrical properties of low-temperature crystallized BST film were studied. The BST thin films have been fabricated at $350^{\circ}C$ by UV-assisted rapidly thermal annealing (RTA). The BST films are in a single perovskite phase and have well-defined electrical properties such as high dielectric constant, low dielectric loss, low leakage current density, and high breakdown voltage. Photoexcitation of the organics contained in the sol-gel-derived films by high-intensity UV irradiation facilitates elimination of the organics and formation of the single-crystalline phase films at low temperatures. The amorphous BST thin film was transformed to a highly (h00)-oriented perovskite structure by high oxygen pressure processing (HOPP) at as low as $350^{\circ}C$. The dielectric properties of BST film were comparable to (or even better than) those of the conventionally processed BST films prepared by sputtering or post-annealing at temperature above $600^{\circ}C$. When external pressure was applied to the well-known contractive BST system during annealing, the nucleation energy barrier was reduced; correspondingly, the crystallization temperature decreased. The UV-assisted RTA and HOPP, as compatible with existing MOS technology, let the BST films be integrated into radio-frequency circuit and mixed-signal integrated circuit below the critical temperature of $400^{\circ}C$.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.147-150
• /
• 1997

In the study, we consider chua's circuit which is a paradigmatic chaotic system belonging to Lur'e form. It is shown that the dynamic behavior of such a system can be influenced in such a way as to obtain out of chaotic behavior a desired periodic orbit corresponding to an unstable periodic trajectory which exists in the system. This kind of control can be achieved via injection of a single continuous time signal representing the output of the system associated with an unstable periodic orbit embedded in the chaotic attractor We investigate the case when this signal is sampled, i.e. we supply to the system the control signal at discrete time moments only.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1485-1488
• /
• 2003

This paper proposes a wireless EMG-based human-computer interface (HCI) for persons with disabilities. For the HCI, four interaction commands are defined by combining three elevation motions of shoulders such as left, right and both elevations. The motions are recognized by comparing EMG signals on the Levator scapulae muscles with double thresholds. A real-time EMG processing hardware is implemented for acquiring EMG signals and recognizing the motions. To achieve real-time processing, filters such as high- and low-pass filter and band-pass and -rejection filter, and a full rectifier and a mean absolute value circuit are embedded on a board with a high speed microprocessor. The recognized results are transferred to a wireless client system such as a mobile robot via a Bluetooth module. From experimental results using the implemented real-time EMG processing hardware, the proposed wireless EMG-based HCI is feasible for the disabled.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.645-648
• /
• 1998

We used a three-dimensional inductance extraction program, Fasthenry for optimal design of the spiral inductors on silicon substrate. The inductance and quality factor of the spiral inductors with various design parameters were calculated so that the optimal parameter value was determined. The spiral inductors then were fabricated using different foundary processes and were measured using the network analyzer and microwave probes. The pad and other parasitics of measurement system were de-embedded using the y-parameter calibration technique. the inductors fabricated using the LG 0.8um process and HP 0.5um process showed the quality factor of 5.8 and 3, respectively. Finally the equivalent circuit farameters of the spiral inductors on silicon substrate were extracted from the measurement data using the matlab.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1798-1799
• /
• 2011

In this paper, A new cost-effective and accurate input noise rejection method for High Speed Counter module of PLC (Programmable Logic Controller) is proposed. By using combination of simple additional logic circuit and the Timer Pulse function of general purpose MPU, Cost-effectiveness and improvement of accuracy of filtering function can be achieved. This proposed method is verified by simulation. This proposed method is much useful for simple industrial controller based on simple microprocessor because of simplicity, accuracy and low cost.