• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.105-109
• /
• 2005

A compact antenna switch module for GSM/DCS dual band applications based on multilayer low temperature co-fired ceramic (LTCC) substrate is presented. Its size is $4.5{\times}3.2{\times}0.8 mm^3$ and insertion loss is lower than 1.0 dB at Rx mode and 1.2 dB at Tx mode. To verify the stability of the developed module to the process window, each block that is diplexer, LPF's and bias circuit is measured by probing method in the variation with the thickness of ceramic layer and the correlation between each block is quantified by calculating the VSWR In the mean while, two types of bias circuits -lumped and distributed - are compared. The measurement of each block and the calculation of VSWR give good information on the behavior of full module. The reaction of diplexer to the thickness is similar to those of LPF's and bias circuit, which means good relative matching and low value of VSWR, so total insertion loss is maintained in quite wide range of the thickness of ceramic layer at both band. And lumped type bias circuit has smaller insertion itself and better correspondence with other circuit than distributed stripline structure. Evaluated ceramic module adopting lumped type bias circuit has low insertion loss and wider stability region of thickness over than 6um and this can be suitable for the mass production. Stability characterization by probing method can be applied widely to the development of ceramic modules with embedded passives in them.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.12
• /
• pp.1196-1203
• /
• 2014

Recently, UFRs (Unmanned Flying Robots) have begun to be utilized in various areas for civilian and military applications. Due to this increased utilization, accidents involving UFRsare also increasing. To prevent or monitor accidents caused by UFRs, high-accuracy positioning information is one of the most important technical elements. This paper proposes an efficient UFR monitoring system which provides accurate UFR positioning information with low-cost onboard elements; a small ARM module based on an embedded Linux operating system, a low-cost single frequency GPS receiver with a cheap patch antenna, and a versatile wireless network interface module. The ground monitoring system employs a dual frequency GPS receiver to generate exact UFR coordinates with cm-level accuracy. By processing the UFR measurements based on the Inverse RTK (Real Time Kinematic) method, the ground monitoring system determines the cm-level accurate coordinates of the UFR. The feasibility of the proposed UFR monitoring system was evaluated by three experiments in terms of data loss and accuracy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.663-666
• /
• 1999

Ground Penetrating Radar (GPR) attached with 1 GHz center frequency antenna has been used to measure a dielectric constant of mortar, and to detect and locate a steel bar embedded inside laboratory size mortar specimens at various depth. Mortar specimens are made for the measurements with the dimensions of 100cm (width)$\times$100cm (length)$\times$14cm (depth). Each specimen has a 13mm diameter D13 steel bar at 2, 4, 6, 8, 10 and 12cm depth. In this paper, results of radar measurments are provided with a sample output, which successfully located the bar. It has been found that the reflected wave of the steel bar interacts with that of surface when the steel bar has the close distance to the surface.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.546-550
• /
• 2003

For dual-band operation, it can be done by loading two pair of narrow slots in the equilateral-triangular patch, one embedded close to the side edges of the patch and the other inserted at the bottom edge of the patch. The obtained two operating frequencies are of same polarization planes. The frequency ratio of the two operating frequencies is turnabled by varing the positions and lengths of the inserted slots at the bottom edge of the patch. In this paper, A single-feed equilateral-triangular microstrip patch with two pairs of narrow slot for dual-frequency operation is printed on the substrate(TMN-4 Rosers Co.) of the 60 miles. the antenna radiation characteristics are calculated by Ensemble ver. 5.0 software, and compared with the experimental results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.8
• /
• pp.792-797
• /
• 2009

This paper presents the evaluation of PID and fuzzy control logic for the lateral position control of a moving web in roll-to-roll (R2R) printed electronics. In addition, we report the implementation of computer simulation software that enables us to develop the control logic in a graphic user interface and to test the controller performance in 3D dynamic environment. A mathematical model of the web dynamics is described first to explain the lateral motion of a moving web. Based on the model, PID and fuzzy controllers are designed, and embedded in the simulation software. Under the simulation conditions for fabricating RFID antenna by R2R printing, the results indicate that the fuzzy controller shows a better performance and can be more suitable for R2R multi-layer printed electronics.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.2
• /
• pp.167-174
• /
• 2000

Ground penetrating radar(GPR) was applied for measuring depths, sizes and intervals of rebars embedded in concrete. A concrete wall was constructed for this study and a sand pool and a concrete block were used for simulation. Result of this study shows that GPR can be used for measuring rebar depths and intervals, even though it is limitary, but that measuring sizes is almost impossible. Simulation with the sand pool was helpful for research on the versatile rebar arrays though signal was not clear as real concrete wall. A concrete block with many cylindrical holes for inserting different sized rebars could not be used for simulator due to many unknown reflective waves. Antenna orientation must be perpendicular to rebars for large reflection signal.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.1
• /
• pp.31-43
• /
• 2015

This study had been aimed to conduct the camera calibration on VLBI antenna in the Space Geodetic Observation Center of Sejong City with a low-cost digital camera, which embedded in a mobile phone to determine the three-dimension position coordinates of the VLBI antenna, based on stereo images. The initial values for the camera calibration have been obtained by utilizing the Direct Linear Transformation algorithm and the commercial digital photogrammetry system, PhotoModeler $Scanner^{(R)}$ ver. 6.0, respectively. The accuracy of camera calibration results was compared with that the camera calibration results, acquired by a bundle adjustment with nonlinear collinearity condition equation. Although two methods showed significant differences in the initial value, the final calibration demonstrated the consistent results whichever methods had been performed for obtaining the initial value. Furthermore, those three-dimensional coordinates of feature points of the VLBI antenna were respectively calculated using the camera calibration by the two methods to be compared with the reference coordinates obtained from a total station. In fact, both methods have resulted out a same standard deviation of $X=0.004{\pm}0.010m$, $Y=0.001{\pm}0.015m$, $Z=0.009{\pm}0.017m$, that of showing a high degree of accuracy in centimeters. From the result, we can conclude that a mobile phone camera opens up the way for a variety of image processing studies, such as 3D reconstruction from images captured.

• Journal of Internet Computing and Services
• /
• v.9 no.1
• /
• pp.43-54
• /
• 2008

In this paper, we implement an automatic entity information management system for smart refrigerator using RFID technology in which objects containing electronic tags are automatically identified using radio wave. Unlike current "smart" refrigerators, the system presented in this paper implements smart tag information acquisition mechanism and real-time information management system to provide various information on entities in refrigerators to local and remote users. As the first step, this paper analyzes the requirements for smart refrigerator system based on the RFID and suggests design considerations. Based on the analysis, we propose and implement an efficient tag location tracking method based on antenna transfer method and an intelligent tag information management system based on embedded database and web server. We also provide a wide range of experimental results on the number of tags identified at a time and the tag recognition ratio according to the RFID antenna transfer speed and the angle between tag reader and tags.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.8
• /
• pp.482-485
• /
• 2005

STSAT-2 is first satellite which is scheduled to launch by first Korea launcher. Ground station Baseband Controller(GBC) for operating STSAT-2 is now developing. GBC control data flow path between satellite operation computers and ground station antennas and count number of received data packets among demodulated audio signals from three antennas and also set data flow path to good-receiving antenna automatically In GBC two uplink FSK modulators(1.2kbps, 9.6kbps) and six downlink FSK demodulators(9.6kbps, 38.4kbps) are embedded. STSAT-2 GBC hardware is more simpler than STSAT-1 GBC by using FPGA in which all digital logic implemented. Now test and debugging of GBC hardware and Software(FPGA Code and CBC Manager Program) is well progressing in SaTReC, KAIST. This paper introduce GBC structure, functions and test results.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.116-118
• /
• 2005

STSAT-2 is first satellite which is scheduled to launch by first Korea launcher. After launch Ground station Baseband Controller(GBC) for operating STSAT-2 is now developing. GBC control data flow path between satellite operation computers and ground station antennas. and GBC count number of received data packets among demodulated audio signals from three antennas and set data flow path to good-receiving antenna automatically. In GBC two uplink FSK modulators(1.2kbps, 9.6kbps) and six downlink FSK demodulators(9.6kbps, 38.4kbps) are embedded. STSAT-2 GBC hardware is more simpler than STSAT-1 GBC by using FPGA in which all digital logic implemented. Now test and debugging of GBC hardware and Software(FPGA Code and GBC Manager Program) is well progressing in SaTReC, KAIST. This paper introduce GBC structure, functions and test results.