• Asian Journal of Atmospheric Environment
• /
• v.5 no.3
• /
• pp.196-203
• /
• 2011

The main aim of this study is to establish methods of morphological preservation and elemental quantification for individual snow crystals. Individual snow crystals were collected at a height of 20 m above ground level. To stabilize and preserve the original morphologies of the snow crystals, cyanoacrylate, which has been used to fix liquid droplets, was applied (Kasahara et al., 2000). Several different kinds of snow crystals (dendrite, sectored plate, quasi-sectored plate, and hexagonal plate) were successively stabilized using this method. The stabilized snow crystals were pretreated with acetone, and then the elemental components contained in a whole snow crystal were quantified with the Particle Induced X-ray Emission (PIXE) analytical technique. The snow crystal residual composition determined in the present study was dominated by sulfur and mineral components, and the elemental mass showed an apparent crystal size dependence, where the elemental mass gradually decreased as the crystal size increased.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.E3
• /
• pp.87-94
• /
• 2005

Wet scavenging by rain drops is a most important removal process of air pollutants. In order to study the scavenging mechanisms of aerosol particles, the characteristics of chemical components in the rain water were examined as a function of the amount of rainfall. Rain water were collected continuously and separated into the soluble and insoluble components. The elemental concentrations in both components were determined by a PIXE analysis. The physical and chemical characteristics of atmospheric aerosols during the rainfall events were measured simultaneously. The elemental concentrations in rain water decreased substantially just after rain started and then gradually declined in subsequential rain fall exceeding 1.0 mm. The large particles were scavenged more easily than the fine particles. Fe, Ti and Si in rain water were in high insoluble state. Contrarily, almost whole of S was dissolved in rain water.

• Particle and aerosol research
• /
• v.18 no.3
• /
• pp.69-77
• /
• 2022

In order to understand the characteristics of fine particles emitted from coal-fired power plant stacks, it is important to analyze the size distribution and components of particles. In this study, particle size distributions were measured using the ejector-porous tube dilution device and an ELPI system at a stack in a coal-fired power plant. Main elemental components of particles in each size interval were also identified through TEM-EDS analysis for the particles collected in each ELPI stage. Particle size distributions based on number and mass were analyzed with component distributions from 0.006 to 10 ㎛. The highest number concentration was about 0.01 ㎛. The main component of the particles consisted of sulfur, which indicated that sulfate aerosols were generated by gas-to-particle conversion of SO2. In a mass size distribution, a mono-modal distribution with a mode diameter of about 2 ㎛ was shown. For the components of PM1.0 (particles less than 1 ㎛), the abundance order was F > Mg > S > Ca, and however, for the components of PM10 (particles less than 10 ㎛), it was in the order of Fe > S > Ca > Mg. The elemental components by particle size were confirmed.

• Journal of Environmental Health Sciences
• /
• v.48 no.2
• /
• pp.66-74
• /
• 2022

Background: The health effects of particulate matter (PM_2.5) bonded with various harmful chemicals differ based on their composition, so investigating and managing their concentrations and composition is vital for long-term management. As industrial complexes emit considerable quantities of pollutants, higher PM_2.5 concentrations and chemical component effects are expected than in other places. Objectives: We investigated the concentration distribution ratios of PM_2.5 chemical components to provide basic data to inform future major emissions control and PM_2.5 reduction measures in industrial complexes. Methods: We monitored five sites near the Ansan and Siheung industrial complexes from August 2020 to July 2021. Samples were collected and analyzed twice per week in spring/winter and once per week in summer/autumn according to the National Institute of Environmental Research in the Ministry of Environments' Air Pollution Monitoring Network Installation and Operation Guidelines. We investigated and compared composition ratios of 29 ions, carbon, and elemental components in PM_2.5. Results: The analysis of PM_2.5 components at the five sites revealed that ion components accounted for the greatest total mass at approximately 50% while carbon components and elemental components contributed 23~28% and 8~10%, respectively. Among the ionic components, NO₃^- occupies the greatest proportion. OC occupies the greatest proportion of the carbon components and sulphur occupies the greatest proportion of elemental components. Conclusions: This study investigated the concentration distribution ratios of PM_2.5 chemical components in industrial complexes. We believe these results provide basic chemical component concentration ratio data for establishing future air management policies and plans for the Ansan and Siheung industrial complexes.

• Clean Technology
• /
• v.19 no.4
• /
• pp.453-458
• /
• 2013

Fly ash has capacity to oxidize or adsorb mercury in a flue gas. Mercury oxidation and adsorption efficiencies of fly ash vary depending on the properties of fly ash. This study was designed to understand reaction characteristics of mercury with fly ash components. The fly ash components were tested to determine their oxidation and adsorption capabilities for elemental mercury and oxidized mercury. A sample was synthesized with fly ash components and tested. The test results were compared with those of the fly ash sample obtained from a coal-fired power plant. $Fe_2O_3$, CuO and carbon black showed higher oxidation or adsorption efficiency for elemental mercury while CaO, MgO, CuO and carbon black showed higher adsorption efficiency for mercury chloride. In addition, the synthesized sample showed comparable mercury oxidation and adsorption efficiencies to the fly ash sample.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1782-1786
• /
• 2008

To investigate the characteristics of elemental components of atmospheric particles in Cheonan, atmospheric particles were sampled using a high volume air sampler equipped with a 5-stage cascade impactor during 2006. 16 elemental concentrations in fine and coarse particles were determined using ICP-AES and ICP-MS. The total mass concentrations of fine and coarse particles were 33.23 and $20.66{\mu}g/m3$, respectively, and the total elemental concentrations were 1.27, $1.71{\mu}g/m3$, occupying 3.8 and 8.3% of the total mass. Fe, Al, Ti were the most abundant elements in both fine and coarse particles, and the total Pb concentration was 84.55ng/m3, below the National standard. Enrichment factor for Sc, Cr, Cu, Zn, As, Se, Sn, Pb in fine particles were above 1,000. This indicates that the elements in fine particles are mainly from the anthropogenic sources including automobiles.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.19-24
• /
• 2000

The objective of this study is to develope a computer simulation model and estimate theoretically the transient performance characteristics of heat exchangers in an automotive air-conditioning system. To do that, the mathematical modelling of heat exchangers, such as evaporator and condenser, is presented first of all. For detail calculation, evaporator and condenser are divided into many sub-sections. Each sub-section is an elemental volume for transient modelling. The elemental volume is assumed to consist of three components, refrigerant, tube with fin, and air, and various properties including temperatures of three components are determined step along sub-sections. The properties of refrigerant R134a and air are calculated directly in the program. The heat transfer coefficients and pressure drop in single or two phase are also calculated by suitable empirical correlations. The overall tendencies of the simulation results were agreed well with those of actual situation.

• Journal of Conservation Science
• /
• v.20
• /
• pp.55-65
• /
• 2007

Black surface layers collected from stone pagodas were analyzed to study the effects of carbon compounds on the blackening of stone surface layer. The total amounts of carbon was measured through elemental analyser. Organic and elemental carbon were measured by combustion ihrornatographic $CO_2$ determination after elimination of carbonates carbon with acid treatment. The elemental carbon concentration in the black surface layer measured 0.52wt.%. This value is not sufficient to explain the complete blackening of stone surface. To trace the origin of carbon in black surface layer on the stone pagoda, aerosol samples for PM 10 were collected at the near sites of the pagoda. The major components of them were soluble ions(42.8wt.%), carbon(38.4 wt.%) and crustal matter(16wt.%). From the high content(13wt.%) of elemental carbon in aerosol ran be deduced that it may be a prime origin for the elemental carbon in the black surface layer on the stone pagoda. The crustal matter in aerosol can be also a origin of silicate mineral in black surface layer and plays a important role in the darkening of black surface layer.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1185-1186
• /
• 2006

In order to obtain specific magnetic properties, it is of paramount importance to increase the alloy density of components fabricated by powder metallurgy. An alternative to increase the density of alloys such as Fe-49Co-2V would be the use of elemental Fe and Co instead of the pre-alloyed powder. Trying to give some insight on the industrial application of this strategy, this paper investigates the replacement of more conventional pre-alloyed Fe-49Co-2V powders with elemental Fe and Co. A previous analysis shows that it is possible to achieve higher densities and leads to a noticeable improvement in some important magnetic properties.

• Journal of Environmental Health Sciences
• /
• v.36 no.1
• /
• pp.61-71
• /
• 2010

Intensive measurements of airborne respirable $PM_{2.5}$ and inhalable $PM_{2.5}$ were conducted in the downtown area of Iksan city. The $PM_{2.5}$ and $PM_{2.5}$ samples were collected twice a day in the Iksan city of Korea from October 17 to November 1, 2004. The purpose of the study was to determine the inorganic water-soluble components and trace elements of $PM_{2.5}$ and $PM_{2.5}$ in the atmospheric environment and estimate the contribution rate of major chemical components from a mass balance of all measured particulate species. The chemical analysis for PM samples was conducted for water-soluble inorganic ions using ion chromatography and trace elements using PIXE analysis. The mean concentrations of respirable $PM_{2.5}$ and inhalable $PM_{2.5}$ were $51.4{\pm}29.7$ and $79.5{\pm}39.6\;{\mu}g/m^3$, respectively, and the ratio was 0.62. The ion species of $NO_3$, $SO_4^2$, and $NH_4^+$ were abundant in both $PM_{2.5}$ and $PM_{2.5}$. These components predominated in respirable $PM_{2.5}$ fraction, while $Na^+$, $Mg^{2+}$, $Ca^{2+}$ mostly existed in coarse particle mode. Elemental components of S, Cl, K, and Si were abundant in both $PM_{2.5}$ and $PM_{2.5}$. These elements, except for Si, were considered to be emitted from anthropogenic sources, while Si, Al, Fe, Ca existed mainly in coarse particle mode and were considered to be emitted from crustal materials. The averaged mass balance analysis showed that ammonium nitrate, ammonium sulfate, crustal component, and other trace elements were composed of 18.4%, 13.2%, 4.8%, 3.5% for PM2.5 and 17.0%, 11.6%, 13.7%, 4.4% for $PM_{2.5}$, respectively.