• Bulletin of the Korean Chemical Society
• /
• 제18권9호
• /
• pp.916-922
• /
• 1997

A superconducting phase La2CuO4+δ (Tc=44 K) has been prepared by electrochemical oxidation which allows the oxygen to intercalat into the La2O2 layers. According to the Cu K-edge X-ray absorption near edge structure spectroscopic analysis, the oxidized phase shows an overall spectra shift of about 0.5 eV to a higher energy region compared to the as sintered one with the occurrence of an additional peak corresponding to the transition to the |1s13dn+1L-14pσ1 > final state, indicating the oxidation of CuO2 layer. From the X-ray photoelectron spectroscopic studies, it is found that the binding energy of La 3d5/2 is significantly shifted from 834.3 eV (as sintered La2CuO4) to 833.6 eV (as electrochemically oxidized La2CuO4+δ), implying that the covalency of the (La-O) bond is decreased due to the oxygen intercalation. The O 1s spectra do not provide an evidence of the superoxide or peroxide, but the oxide (O2-) with the contaminated carbonate (CO32-) based on the peaks at 529 eV and 532 eV, respectively, which is clearly confirmed by the Auger spectroscopic analysis. Oxygen contents determined by iodometric titration (δ=0.07) and thermogravimetry (δ=0.09) show good coincidence each other, also giving an evidence for the "O2-" nature of excess oxygen. From the above results, it is concluded that "O2-" appeared as O 1s peak at 528.6 eV is responsible for superconductivity of La2CuO4+δ.

• Journal of Electrochemical Science and Technology
• /
• 제14권4호
• /
• pp.388-396
• /
• 2023

Photoelectrochemical (PEC) water splitting is a vital source of clean and sustainable hydrogen energy. Moreover, the large-scale H₂ production is currently necessary, while long-term stability and high PEC activity still remain important issues. In this study, a GaN-based photoelectrode was modified by an additional NH₃ treatment (900℃ for 10 min) and its PEC behavior was monitored. The bare GaN exhibited a highly crystalline wurtzite structure with the (002) plane and the optical bandgap was approximately 3.2 eV. In comparison, the NH₃-treated GaN film exhibited slightly reduced crystallinity and a small improvement in light absorption, resulting from the lattice stress or cracks induced by the excessive N supply. The minor surface nanotexturing created more surface area, providing electroactive reacting sites. From the surface XPS analysis, the formation of an N-Ga-O phase on the surface region of the GaN film was confirmed, which suppressed the charge recombination process and the positive shift of E_FB. Therefore, these effects boosted the PEC activity of the NH₃-treated GaN film, with J values of approximately 0.35 and 0.78 mA·cm^-2 at 0.0 and 1.23 V_RHE, respectively, and an onset potential (V_on) of -0.24 V_RHE. In addition, there was an approximate 50% improvement in the J value within the highly applied potential region with a positive shift of V_on. This result could be explained by the increased nanotexturing on the surface structure, the newly formed defect/trap states correlated to the positive V_on shift, and the formation of a GaO_xN_1-x phase, which partially blocked the charge recombination reaction.

• 한국재료학회지
• /
• 제29권12호
• /
• pp.790-797
• /
• 2019

To improve photocatalytic performance, CdS nanoparticle deposited TiO₂ nanotubular photocatalysts are synthesized. The TiO₂ nanotube is fabricated by electrochemical anodization at a constant voltage of 60 V, and annealed at 500 for crystallization. The CdS nanoparticles on TiO₂ nanotubes are synthesized by successive ionic layer adsorption and reaction method. The surface characteristics and photocurrent responses of TNT/CdS photocatalysts are investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), UV-Vis spectrometer and LED light source installed potentiostat. The bandgaps of the CdS deposited TiO₂ photocatalysts are gradually narrowed with increasing of amounts of deposited CdS nanoparticles, which enhances visible light absorption ability of composite photocatalysts. Enhanced photoelectrochemical performance is observed in the nanocomposite TiO₂ photocatalyst. However, the maximum photocurrent response and dye degradation efficiency are observed for TNT/CdS30 photocatalyst. The excellent photocatalytic performance of TNT/CdS30 catalyst can be ascribed to the synergistic effects of its better absorption ability of visible light region and efficient charge transport process.

• Corrosion Science and Technology
• /
• 제19권1호
• /
• pp.16-22
• /
• 2020

It is important to realize that benzoate was intercalated into hydrotalcite (HTC-Bz) by the co-precipitation method. In this case, acrylic coating with 0.5 wt% HTC-Bz was deposited on carbon steel using the spin coating method. Next, the HTC-Bz structure was characterized by Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). In fact, an ultraviolet vision spectroscopy (UV-Vis) was used to determine the benzoate content in HTC-Bz, and the UV absorption ability of HTC-Bz. Using electrochemical techniques, water contact angle measurement, and thermal-gravimetric analysis, we compared the protective properties before and after QUV test, hydrophobicity and the thermal stability of acrylic coating containing HTC-Bz. The obtained results showed that HTC-Bz with a plate-like structure was successfully synthesized; benzoate was intercalated into the interlayer of hydrotalcite with a concentration of 28 wt%. Additionally, it was noted that HTC-Bz has an UV absorption peak at 225 nm. In conclusion, the addition of HTC-Bz enhanced the UV stability, hydrophobicity and the thermal stability of acrylic coating.

• 한국재료학회지
• /
• 제32권1호
• /
• pp.14-22
• /
• 2022

To improve light absorption ability in the visible light region and the efficiency of the charge transfer reaction, Pd nanoparticles decorated with reduced TiO₂ nanotube photocatalyst were synthesized. The reduced TiO₂ nanotube photocatalyst was fabricated by anodic oxidation of Ti plate, followed by an electrochemical reduction process using applied cathodic potential. For TiO₂ photocatalyst electrochemically reduced using an applied voltage of -1.3 V for 10 min, 38% of Ti⁴⁺ ions on TiO₂ surface were converted to Ti³⁺ ion. The formation of Ti³⁺ species leads to the decrease in the band gap energy, resulting in an increase in the light absorption ability in the visible range. To obtain better photocatalytic efficiency, Pd nanoparticles were decorated through photoreduction process on the surface of reduced TiO₂ nanotube photocatalyst (r10-TNT). The Pd nanoparticles decorated with reduced TiO₂ nanotube photocatalyst exhibited enhanced photocurrent response, and high efficiency and rate constant for aniline blue degradation; these were ascribed to the synergistic effect of the new electronic state of the TiO₂ band gap energy induced by formation of Ti³⁺ species on TiO₂, and by improvement of the charge transfer reaction.

• Composites Research
• /
• 제36권3호
• /
• pp.217-223
• /
• 2023

본 연구에서는 폴리아크릴로니트릴계 탄소나노섬유 스펀지의 제조 및 오일 흡착 거동을 조사하였다. 제조된 탄소나노섬유 스펀지는 물과 기름의 혼합용액에서 우수한 선택적 오일 흡착 능력을 보였으며, 탄소나노섬유 스펀지의 재사용시 흡착 능력도 확인하였다. 또한, 흡착제 내부구조에 정렬된 채널을 형성함으로써, 모세관 현상에 의하여 빠른 오일 흡착 거동을 보이는 탄소나노섬유 스펀지를 제조할 수 있었다. 이후 사용 폐기된 탄소나노섬유 스펀지는 질소 분위기에서 800℃로 열처리하여, 4-아미노페놀의 전기화학적 검출을 위한 센서로의 가능성을 검토하였다.

• 방사성폐기물학회지
• /
• 제9권3호
• /
• pp.121-129
• /
• 2011

전기화학적으로 생성되는 $Ag^{2+}$를 사용하는 MEO 공정에 의한 NO 제거에 전류밀도, $AgNO_3$ 농도, 세정 용액의 유속 및 NO-공기 혼합가스 유속이 미치는 영향을 조사하였다. 전류밀도가 증가할수록 NO의 산화 반응 속도 및 제거 효율이 증가하였으며, 0.1 M 이상의 $AgNO_3$ 농도 조건에서 ㅍ 농도가 NO의 제거 효율에 미치는 영향은 무시할 만 하였다. 세정용액의 유속이 증가할수록 NO의 제거효율은 점진적으로 증가한 반면에 NO-공기 혼합가스의 유속이 증가할수록 NO의 제거효율은 점진적으로 감소하였다. 실험 범위 내에서 도출한 최적조건을 적용한 MEO 공정 및 3 M 질산 흡수 공정을 복합적으로 적용하여 NO-공기 혼합가스를 처리하였으며, NO 및 $NO_x$의 제거 효율은 각각 95% 및 63%를 얻었다.

• Macromolecular Research
• /
• 제17권10호
• /
• pp.791-796
• /
• 2009

An electrochemically and photochemically polymerizable monomer, 2-((2,3-dihydrothieno[3,4-b] [1,4]dioxin-2-yl)methoxy)ethyl methacrylate (EDOT-EMA), was explored for patterning of poly(3,4-ethylenedioxythiophene) (PEDOT) via side chain cross-linking. The polymer from EDOT-EMA was deposited electrochemically to produce polymeric EDOT (PEDOT-EMA), which was directly photo-patterned by UV light as the side EMA groups of PEDOT-EMA were polymerized to give cross-linked EMA (PEDOT-PEMA). Absorption and FTIR studies of the UV-exposed film (PEDOT-PEMA) indicated that the photo-patterning mainly originated from the photo cross-linking of the methacrylates in the side-chain. After irradiation of the film, the conductivity of the irradiated area decreased from $5.6{\times}10^{-3}$ S/cm to $7.2{\times}10^{-4}$ S/cm, possibly due to bending of the conductive PEDOT channel as a result of the side chain cross-linking. The patterned film was applied to a solid state electrochromic (EC) cell to obtain micro-patterned EC cells with lines up to 5 ${\mu}m$ wide.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.61-64
• /
• 2008

$Pr_{0.3}Sr_{0.7}Co_{0.3}Fe_{0.7}O_{3-\delta}$ (PSCF3737) was prepared and characterized as a cathode material for intermediate temperature-operating solid oxide fuel cell (IT-SOFC). X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS), and electrical property measurement were carried out to study cathode performance of the material. XPS and EXAFS results proved that oxygen vacancy concentration was decreased and lattice constants of the perovskite structure material were increased by doping Fe up to 70 mol% at B-site of the crystal structure, which also extended the distance between oxygen and neighbor atoms. Thermal expansion coefficient (TEC) of PSCF3737 is smaller than that of $Pr_{0.3}Sr_{0.7}CoO_{3-\delta}$(PSC37) due to lower oxygen vacancy concentration. PSCF3737 showed better cathode performance than PSC37. It might be due good adhesion by a smaller difference of TEC between $Gd_{0.1}Ce_{0.9}O_2$ (CGO91) and electrode. Composite material PSCF3737-CGO91 showed better compatibility of TEC than PSCF3737. However, PSCF3737-CGO91 did not represent higher electrochemical property than PSCF3737 due to decreased reaction sites by CGO91.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.36-36
• /
• 2008

Organic light-emitting device (OLED) have become very attractive due to their potential application in flat panel displays. One important problem to be solved for practical application of full-color OLED is development of three primary color (Red, Green and Blue) emitting molecule with high luminous operation. Particularly, the development of organic materials for blue electroluminescence (EL) lags significantly behind that for the other two primary colors. For this reason, Flu-Si was synthesized and characterized by means of high-resolution mass spectro metry and elemental analyses. Flu-Si has the more wide optical band gap (Eg = 3.86) than reference material (Cz-Si, Eg = 3.52 eV). We measured the photophysical and electrochemical properties of Flu-Si. The HOMO-LUMO levels were estimated by the oxidation potential and the onset of the UV-Vis absorption spectra. The EL properties were studied by the device fabricated as a blue light emitting material with FIrpic.