• 전기학회논문지
• /
• 제65권5호
• /
• pp.738-744
• /
• 2016

Current rating of a power cable can be calculated by the maximum allowable temperature in an insulating material considering the heat transfer from cable conductor. Therefore, it is very important to calculate the current rating using electrical equivalent circuit by calculated cable thermal circuit parameters but, it has not been fully investigated yet. In this paper, in order to determine the current rating of power cable, conventional calculation method has been reviewed considering the conductor resistance, loss factor of sheath, dielectric losses and thermal resistances based on the maximum allowable temperature of 345 kV $2500mm^2$ XLPE cable. To confirm the calculation result of the current rating, the conductor temperature should be examined whether it reaches the maximum allowable temperature by the thermal equivalent circuit of the cable. Then, utilizing EMTP (Electro-Magnetic Transient Program) which is a conventional program for electrical circuit, the thermal equivalent circuit was transformed to an electric equivalent circuit using an analogous relationship between thermal circuit and electrical circuit, and temperature condition including cable conductor, sheath, cable jacket could be calculated by the current rating of 345 kV $2500mm^2$ XLPE cable.

• KSBB Journal
• /
• 제5권2호
• /
• pp.175-182
• /
• 1990

N. tabacum $NR^-/SR^+$과 N. glutinosa의 엽육세포로부터 원형질체를 분리하여 전기적으로 융합 및 배양하였으며 AAPI 9M 배지에서 이 원형질체의 plating effici-ency는 30~35%였다. 분열 중인 소형 세포괴는 1.2mg / ml의 streptomycin이 포함된 $MSNO_3$배지에 치상하여 계속 분열을 유지하는 녹색 칼루스 계통을 선발하였다. 이 녹색 칼루스 계통에서 유래된 4계통의 식물들은 꽃의 형태, 화관의 길이와 염신의 모양에서 양쪽 모식물체의 중간형을 보였고, 엽조직의 peroxidase와 esterase의 isozyme분석에서도 양쪽 모식물체의 특성을 부분적으로 함께 나타냈으며 또한 결실되거나 새로운 isozyme band도 보였다. 이 융합체 추정계통들의 염색체 분석에서 L22계통에서 2n=66, L44계통에서 2n=54개가 조사되어 N.tabacum(2n=48)과 N.glutinosa(2n=24)의 융합체는 염색체의 부분적 감소현상을 보였다.

• Journal of Information Display
• /
• 제2권2호
• /
• pp.52-60
• /
• 2001

The electrical and mechanical properties in indium-tin-oxide films deposited on polymer substrate were examined. The materials of substrates were polyethersulfone (PES) which have gas barrier layer and anti-glare coating for plastic-based devices. The experiments were performed by rf-magnetron sputtering using a special instrument and buffer layers. Therefore, we obtained a very flat polymer substrate deposited ITO film and investigated the effects of buffer layers, and the instrument. Moreover, the influences of an oxygen partial pressure and post-deposition annealing in ITO films deposited on polymer substrates were clarified. X-ray diffraction observation, measurement of electrical property, and optical microscope observation were performed for the investigation of micro-structure and electro-mechanical properties, and they indicated that as-deposited ITO thin films are amorphous and become quasi-crystalline after adjusting oxygen partial pressure and thermal annealing above $180^{\circ}C$. As a result, we obtained 20-25 ${\Omega}/sq$ of ITO films with good transmittance (above 80 %) of oxygen contents with under 0.2 % and vacuum annealing. Furthermore, using organic buffer layer, we obtained ITO films which have a rather high electrical resistance (40-45 ${\Omega}/sq$) but have improved optical (more than 85 %) and mechanical characteristics compared to the counterparts. Consequently, a prototype reflective color plastic film LCD was fabricated using the PES polymer substrates to confirm whether the ITO films could be realized in accordance with our experimental results.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.259-264
• /
• 2005

The copper clad steel wire is used extensively as lead wires of electronic components such as capacitors, diodes and glass sealing lamp because the wire combines the strength and low thermal expansion characteristic of Fe-Ni steel with the conductivity and corrosion resistance of copper. In order to fabricate the copper clad steel wire, several processes including electro-plating, tubecladding extrusion process and dip forming process have been introduced and applied. The electroplating process for the production of copper clad steel wire shows poor productivity and induces environmental load generation such as electroplating solution. The dip forming process is suitable to mass production of copper clad steel such as trolley wire. and need expensive manufacturing facilities. The present paper describes the improvement of the conventional continuous casting process to fabricate copper clad steel wire, which its core metal is low thermal expansion Fe-Ni alloy and its sheath material is copper. In particular, the formation of intermetallic compound at interface between core and sheath was investigated in order to introduce optimum continuous casting process parameter for fabrication of copper clad steel wire with higher electrical conductivity. The mechanical strength of copper clad steel wire was also investigated through wiredrawing process with of 95% in total reduction ratio.

• 전기학회논문지
• /
• 제63권10호
• /
• pp.1364-1370
• /
• 2014

Power system fault analysis has been based on symmetrical component method, which describes power system elements by positive, negative and zero sequence impedance. Obtaining accurate line impedances as possible are very important for estimating fault current magnitude and setting distance relay accurately. Especially, accurate calculation of zero sequence impedance is important because most of transmission line faults are line-to-ground faults, not balanced three-phase fault. Since KEPCO has started measuring of transmission line impedance at 2005, it has been revealed that the measured and calculated line impedances are well agreed within reasonable accuracy. In case of underground transmission lines, however, large discrepancies in zero sequence impedance were observed occasionally. Since zero sequence impedance is an important input data for distance relay to locate faulted point correctly, it is urgently required to analyze, detect and consider countermeasures to the source of these discrepancies. In this paper, development of pre/post processor to ATP (Alternative Transient Program) version of EMTP (Electro-Magnetic Transient Program) for sequence impedance calculation was described. With the developed processor ATP-cable, effects of ground resistance and ECC (Earth Continuity Conductor) on sequence impedance were analyzed.

• Nuclear Engineering and Technology
• /
• 제39권3호
• /
• pp.231-236
• /
• 2007

Due to the occasional occurrences of stress corrosion cracking(SCC) in steam generator tubing(Alloy 600), degraded tubes are removed from service by plugging or are repaired for re-use. Since electrodeposition inside a tube does not entail parent tube deformation, residual stress in the tube can be minimized. In this work, tube restoration via electrodeposition inside a steam generator tubing was performed after developing the following: an anode probe to be installed inside a tube, a degreasing condition to remove dirt and grease, an activation condition for surface oxide elimination, a tightly adhered strike layer forming condition between the electro forming layer and the Alloy 600 tube, and the condition for an electroforming layer. The reliability of the electrodeposited material, with a variation of material properties, was evaluated as a function of the electrodeposit position in the vertical direction of a tube using the developed anode. It has been noted that the variation of the material properties along the electrodeposit length was acceptable in a process margin. To improve the reliability of a material property, the causes of the variation occurrence were presumed, and an attempt to minimize the variation has been made. A Ni alloy electrodeposition process is suggested as a primary water stress corrosion cracking(PWSCC) mitigation method for various components, including steam generator tubes. The Ni alloy electrodeposit formed inside a tube by using the installed assembly shows proper material properties as well as an excellent SCC resistance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.763-764
• /
• 2013

A three-dimensional image capturing device and its signal processing algorithm and apparatus are presented. Three dimensional information is one of emerging differentiators that provides consumers with more realistic and immersive experiences in user interface, game, 3D-virtual reality, and 3D display. It has the depth information of a scene together with conventional color image so that full-information of real life that human eyes experience can be captured, recorded and reproduced. 20 Mega-Hertz-switching high speed image shutter device for 3D image capturing and its application to system prototype are presented[1,2]. For 3D image capturing, the system utilizes Time-of-Flight (TOF) principle by means of 20MHz high-speed micro-optical image modulator, so called 'optical resonator'. The high speed image modulation is obtained using the electro-optic operation of the multi-layer stacked structure having diffractive mirrors and optical resonance cavity which maximizes the magnitude of optical modulation[3,4]. The optical resonator is specially designed and fabricated realizing low resistance-capacitance cell structures having small RC-time constant. The optical shutter is positioned in front of a standard high resolution CMOS image sensor and modulates the IR image reflected from the object to capture a depth image (Figure 1). Suggested novel optical resonator enables capturing of a full HD depth image with depth accuracy of mm-scale, which is the largest depth image resolution among the-state-of-the-arts, which have been limited up to VGA. The 3D camera prototype realizes color/depth concurrent sensing optical architecture to capture 14Mp color and full HD depth images, simultaneously (Figure 2,3). The resulting high definition color/depth image and its capturing device have crucial impact on 3D business eco-system in IT industry especially as 3D image sensing means in the fields of 3D camera, gesture recognition, user interface, and 3D display. This paper presents MEMS-based optical resonator design, fabrication, 3D camera system prototype and signal processing algorithms.

• 대한기계학회논문집A
• /
• 제37권1호
• /
• pp.1-8
• /
• 2013

자동차용 냉각기 고무호스는 열과 기계적 하중을 받으면서 국부적으로 형성된 전기적 영향으로 인해 노화와 고장이 발생한다. 본 연구에서는 개선된 시험방법을 이용하여 고무호스의 파괴거동을 재현하였다. 냉각기 고무호스 재료인 카본블랙이 함유된 EPDM 고무를 사용하여 인장응력과 전기화학적 복합 스트레스를 가하여 노화거동을 분석하였다. 노화 시간에 따른 전류 및 저항의 변화거동을 관찰하였으며 인장 변형 스트레스와 전압 및 노화온도 조건에 따른 노화거동을 분석하였다. 고무 시험편을 수직면으로 정밀하게 절단하여 시험편 표면 및 내부의 변화거동을 분석하여 전기화학적 노화거동과 고장메커니즘을 규명하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권3호
• /
• pp.138-143
• /
• 2010

최근 들어 대형 해양콘크리트 구조물의 건설이 빈번해짐에 따라 콘크리트의 염화물이온확산계수를 정확히 평가할 필요성이 대두되고 있으나, 콘크리트의 염화물이온 확산계수 평가는 장시간이 소요되는 단점 때문에 전기화학적인 전위차 촉진에 의해 단시간에 염화물이온의 확산계수를 추정하기 위한 여러 촉진 시험방법들이 제안되고 있으나 이에 대한 체계적인 연구가 아직은 미비한 실정이다. 따라서 본 연구에서는 시멘트의 성분이 다른 3종류의 시멘트를 대상으로 대표적인 3가지 전기적인 촉진시험에 의해 콘크리트중의 염화물이온의 침투 및 확산특성을 평가하고 이 방법간의 상관성을 분석하였다. 평가결과 시멘트의 성분에 따라 염화물이온의 확산특성은 크게 달라졌으며, 그 중 고로 슬래그 미분말과 플라이애시를 일정비율로 혼합한 3성분계 시멘트의 확산특성이 가장 우수하였으며, 염화물이온 확산 특성은 결과로부터 시험방법간의 상관성은 양호한 것으로 나타났다.

• Journal of Electrochemical Science and Technology
• /
• 제12권2호
• /
• pp.246-256
• /
• 2021

Mo,Cu-doped CeO₂ (CMCuO) nanopowders were synthesized by the nitrate-fuel combustion method aiming to improve the electrical and electrochemical properties of its Mo-doped CeO₂ (CMO) parent by the addition of copper. An electrical conductivity of ca. 1.22·10^-2 S cm^-1 was measured in air at 800℃ for CMCuO, which is nearly 10 times higher than that reported for CMO. This increase was associated with the inclusion of copper into the crystal lattice of ceria and the presence of Cu and Cu₂O as secondary phases in the CMCuO structure, which also could explain the increase in the charge transfer activities of the CMCuO based anode for the hydrogen and carbon monoxide electro-oxidation processes compared to the CMO based anode. A maximum power density of ca. 120 mW cm^-2 was measured using a CMCuO based anode in a solid oxide fuel cell (SOFC) with YSZ electrolyte and LSM-YSZ cathode operating at 800℃ with humidified syngas as fuel, which is comparable to the power output reported for other SOFCs with anodes containing copper. An increase in the area specific resistance of the SOFC was observed after ca. 10 hours of operation under cycling open circuit voltage and polarization conditions, which was attributed to the anode delamination caused by the reduction of the Cu₂O secondary phase contained in its microstructure. Therefore, the addition of a more electroactive phase for hydrogen oxidation is suggested to confer long-term stability to the CMCuO based anode.