• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.69-76
• /
• 1995

This paper describes characteristics of EDT(Electro Discharge Texturing) and that the strip surface has influence on the paintability. The pulse mode and the capacitor mode of recently developed EDT method were investigated about the peak shape and the roughness of strip surface. And EDT method compared the above-mentioned contents with the SBT(Shot Blast Texturing) method. The peak count of the pulse mode is more than that of the capacitor mode. But the lower roughness below the Ra 3.2 .mu. m of the strip surface, the texturing time of the pulse mode is longer than the capacitor mode. In SBT method, the peak shape is similar to capacitor mode. But the EDT roll has more uniformity than the SBT roll and has more peak count than that of SBT roll. Therefore, in the painted steel sheet, EDT roll gives better surface of clarity image than the SBT roll.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.132-136
• /
• 1996

A Study is a experiment which is figure out to aptimum discharge cutting condition of the surfaceroughness, electric discharging speed and electro wear ratio with Ton Toff and V(voltage) as an input condition according to the current(Ip) in an electric spark machine ; 1)Electrode is utilized Cu(coper) and Graphite. 2)Work piece is used the material of carbon steel. The condition of experiment is; 1)Current is varied 0.7(A) to 50(A). 2)Pulse time(Ton) is varied 3($\mu$s) to 240($\mu$s) and also Toff is varied 7($\mu$s) to 20($\mu$s). 3)The time of electric discharging to work piece in each time is 30(min) to 60(min) 4)After the upper side of work piece was measured in radius (5${\mu}{\textrm}{m}$) of syulus analyzed the surface roughness to made the table and graph of Rmax by yielding data. 5)Electro wear ratio is; \circled1Coper was measured cx-machining and post machining but the electronic baiance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume specific gravity and analyzed to made its table and graph on ground the data 6)In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V.R(Automatic Voltage Regulator). 7)The memory scope was sticked to the electric spark machine. 8)In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid, it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging According to above results, the surface roughness by the variation of electrodw and current was analyzed to compare KS(Korea Standards) It was decided the optimum condition of electric discharge cutting through analyzing the effect of electric discharge speed and electro wear ratio.

• ETRI Journal
• /
• v.30 no.6
• /
• pp.833-843
• /
• 2008

The effect of forward and reverse electrostatic discharge (ESD) on the electro-optical characteristics of oxide vertical-cavity surface-emitting lasers is investigated using a human body model for the purpose of understanding degradation behavior. Forward ESD-induced degradation is complicated, showing three degradation phases depending on ESD voltage, while reverse ESD-induced degradation is relatively simple, exhibiting two phases of degradation divided by a sudden distinctive change in electro-optical characteristics. We demonstrate that the increase in the threshold current is mainly due to the increase in leakage current, nonradiative recombination current, and optical loss. The decrease in the slope efficiency is mainly due to the increase in optical loss.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.42-45
• /
• 2004

Electrochemical discharge machining (ECDM) has been found to be suitable for the micro-hole machining of nonconductive materials such as ceramics or glass compared with existing conventional and also non-conventional machining methods. However this machining process has some problems such as low geometric accuracy and low machining efficiency due to the random spark generation at the end of the electrode. This paper proposes the methods to improve the geometric accuracy of micro-hole using powder mixed ECDM process. The experimental results show the effects of powder producing improved geometric accuracy of machined hole and decreased concentration of spark energy.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.232-236
• /
• 2015

The electro-optical characteristics of several functional layers over the MgO protective layer were studied during the continuous discharge of an AC-PDP. In order to observe the degradation of each functional layer on the MgO protection layer, we measured the surface morphology, cathodoluminescence (CL) spectrum, the secondary electron emission coefficient (${\gamma}$) and the discharge characteristics after 500 hours of discharge during the operation of the AC-PDP.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.841-846
• /
• 2014

It found that the maximum temperature of the arc discharge occurred on the Silicone rubber sample significantly decreased with increasing the reinforcing agent. It was confirmed that the current value decreased with increasing the aluminium trihydrate($Al(OH)_3$) and the current value increased with reducing the primary resistance over time. Regarding these results, may be it is because the degradation due to the electro-conductive carbonization was improved and the properties of dielectric breakdown was reduced by the flame retardant reinforcing agent. It found that the electro-conductive carbonized road has not happened by increasing the flame retardant reinforcing agent. Regarding to the arc discharge, this study show that the arc arising near the lower electrode of sample has disappeared.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1195-1198
• /
• 2005

The improvement of efficiency is the one of the most important part in AC PDPs . To achieve high efficiency, high VUV emission efficiency and High ion induces secondary electron emission coefficient are needed. We have measured the emission spectra of vacuum ultraviolet rays and ion induced secondary electron emission coefficient of MgO protective layer in surface discharge AC-PDP with binary and ternary gas mixtures. We have investigated electro-optical characteristics of AC-PDPs to optimum gas mixture for high efficient.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.4
• /
• pp.107-113
• /
• 2008

We investigated the electro-optical characteristics of an ICP(Inductively Coupled Plasma) light source depending on driving temperature, and length of discharge tube. An electro-optical stability of a sample at operating was measured to see a steady state of a sample. In this results, we can see that a stability of power loss and luminous flux of a sample at operating of upper 70[min] was 1.45[%1 and 0.36[%]. We measured the optical characteristics of a sample in a thermal chamber operated at a specific temperature divided into 5 steps. While luminance increased with temperature increasing, the decrement of luminance a eared at u or $46.7[^{\circ}C]$. According to Parchen's and Boyle-Charles' law, we can speculate that a pressure was increased and a higher voltage was needed but a ballaster having a rating power can't support a higher voltage corresponding to a pressure change, 0.02[Torr] at $46.7[^{\circ}C]$. Moreover, we measured an a lied power and current of samples depending to a various length of a discharge tube.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.72-78
• /
• 2009

For the electro-discharge machining of an electro-conductive anisotropic composite, an unsteady state formulation was established and solved by Galerkin's finite element method. The distribution of temperature on work piece, the shape of the crater and the material removal rate were obtained in terms of the process parameters. The $12{\times}12$ irregular mesh that was chosen as the optimum in the previous analysis was used for computational accuracy and efficiency. A material having the physical properties of alumina/titanium carbide composite was selected and an electricity with power of 51.4 V and current of 7 A was applied, assuming the removal efficiency of 10 % and the thermal anisotropic factors of 2 and 3. As the spark was initiated the workpiece immediately started to melt and the heat affected zone was formed. The moving boundary of the crater was also identified with time. When the radial and axial conductivities were increased separately, the temperature distribution and the shape of the crater were shifted in the radial and axial directions, respectively. The material removal rate was found to be higher when the conductivity was increased in the radial direction rather than in the axial direction.

• The Journal of the Korea Contents Association
• /
• v.6 no.12
• /
• pp.163-168
• /
• 2006

Hg-free fluorescent lamps were fabricated and electro-optical characterization were measured for using LCD backlight. PDP phosphors, nitro-cellulose and n-butyl acetate were mixed and coated uniformly in glass tube without stain. The glass tubes were sintered at $550^{\circ}C$ for 20 minutes, vacuumed to $10^{-6}$ torr and supplied discharge gas by using a gas mixture. After various experiment about phosphors thickness and inner diameter of glass tube, the appropriate phosphors thickness and inner diameter of glass tube were obtained. The luminance and luminous efficiency of manufactured fluorescent lamps with Ne+Xe discharge gas were $6,270cd/m^2$, 13 lm/W under 75 kHz sinusoidal wave voltage, respectively.