• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.371-374
• /
• 2008

KEPRI has carried out IEC61850 communication conformance test about the IED trial products. This paper describes dataset conformance testing, one of the IEC 61850-10 conformance test items, and test procedures on IED. KEPRI plans to construct the testing field of IEC 61850 based substation automation system with domestic IEDs confirmed their IEC 61850 communication service including dataset.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.513-515
• /
• 1999

In this study, we evaluated the relation of the test and theory of low impedance cable As the result We could obtained the result in accordance the test with theory in 85 ~ 95% tolerance . Test method measured the relation of the current and temperature of cable jacket in using CT to put in 3 phase AC current simultationiously. The current and temperature of it was calculated in according to JCS- l68D

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.617-620
• /
• 2001

The protection of communication lines against harmful effects from electricity lines is very important with the rapid development of communications network. This paper is introduced the reference of noise voltage and the test methods of foreign coutnreis. Further we will also present study measurement equipment for telecommunications noise voltage and circuit noise phenomenon.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.544-550
• /
• 1995

In this paper, the anode for molten carbonate fuel cell have been prepared by doctor blade method and microstructure, pore distribution, sintering test of the electrode were investigated. Component analysis were done by Scanning Electron Micrograph, porosimeter and sintering test apparatus. As a result, median pore size was 11.mu.m order at the major specimen and porosity was about 70%. And thickness loss of the electrode was 1.5% at Ni-10Co anode after sintering test.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.1 s.343
• /
• pp.71-78
• /
• 2006

An NoC (Networks-on-Chip) is an emerging design paradigm intended to cope with a future SoC containing numerous built-in cores. In an NoC, the test strategy is very significant for its practicality and feasibility. Among existing test issues, TAM architecture and test scheduling will particularly dominate the overall test performance. In this paper, we address an efficient NoC test scheduling algorithm based on a rectangle packing approach used for an SoC test. In order to adopt the rectangle packing solution as an NoC test scheduling algorithm we design the configuration about test resources and test methods suitable for an NoC structure. Experimental results using some ITC'02 benchmark circuits show the proposed algorithm can reduce the overall test time by up to $55\%$ in comparison with previous works.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.1
• /
• pp.19-22
• /
• 2018

The thermal and electrical properties of the conductor are critical parametersfor the design and optimization of the superconducting magnet. This paper presents simulation code to analyze electrical and thermal stability characteristics of the second generation (2G) high-temperature superconductor (HTS) by varying copper stabilizer thickness. Two types of commercial 2G HTS coated conductor tapes, YBCO and GdBCO were used in this study. These samples were cooled by Liquid Nitrogen ($LN_2$) having boiling at 77.3 K and an equivalent electrical circuit model for them is choosen and analysed in details. Also, an over-current pulse test in which a current exceeding a critical current was performed. From the simulation results, the influences of the copper stabilizer thickness on the stability characteristics of these samples are presented.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.10 no.2
• /
• pp.1-6
• /
• 2012

Purpose : This study is to investigate the modulatory effects to the ultraviolet induced erythema of pain processing system. Methods : Thirty six healthy volunteers were divided into none treatment group (n=6), indomethacine group (n=6), subsensory level electrical stimulation group (n=6), sensory level electrical stimulation group (n=6), motor level electrical stimulation group (n=6), noxious level electrical stimulation group (n=6). Subjects were induced erythema for three times minimal erythema dose (MED) at upper arm of dermatome C6 level. Each experimental group had mechanical pain threshold (MPT), electrical pain threshold (EPT), thermal pain threshold (TPT). Results : This study revealed that we observed that pain thresholds were significantly correlated with each other in pain processing system. The effect of electrical stimulation levels evaluates were shown to be significant differences pain control effect in electrical stimulation group (sensory, motor level electrical stimulation groups) more than indomethacine group, subsensory level and control group. Conclusion : In this study, it was found that the effect of ultraviolet induced erythema of pain control by modulatory electrical stimulation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.72-85
• /
• 2007

The development of memory design and process technology enabled the production of high density memory. However, this increased the complexity of the memory making memory testing more complicated, and as a result, it brought about an increase in memory testing costs. Effective memory test algorithm must detect various types of defects within a short testing time, and especially in the case of port memory test algorithm, it must be able to detect single port memory defects, and all the defects in the dual port memory. The March A2PF algorithm proposed in this paper is an effective test algorithm that detects all types of defects relating to the duel port and single port memory through the short 18N test pattern.

• Structural Engineering and Mechanics
• /
• v.84 no.2
• /
• pp.155-165
• /
• 2022

The use of electricity and communication between electronic devices is increasing daily, which makes the stability of electrical power supply vital. Since the 1990s, large earthquakes have occurred frequently causing considerable direct damage to electrical power facilities as well as secondary damage, such as difficulty in restoring functions due to the interruption of electric power supply. Therefore, it is very important to establish measures to protect electrical power facilities, such as transformers and switchboards, from earthquakes. In this study, a 154 kV transformer whose service life had expired was installed on the base fabricated by simulating the field conditions and conducting the shaking table tests. The dynamic characteristics and seismic behavior of the 154 kV transformer were analyzed through the resonance frequency search test and seismic simulation test that considers the front, rear, left, and right directions. Since the purpose of this study is to analyze the acceleration amplification in the bushing due to the acceleration amplification, the experimental results were analyzed focusing on the acceleration response and the converted acceleration amplification ratio rather than the failure due to the displacement response of the transformer. The seismic force amplification at the transformer bushing was evaluated by simulating the characteristics of electrical power facilities in South Korea, and compared with the IEC TS 61463 acceleration amplification factor. Finally, the amplification factor at zero period acceleration (ZPA) modified for each return period was summarized. The results of this study can be used as data to define the amplification factor at ZPA of the transformer bushing, simulating the characteristics of electrical power facilities in Korea.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.55-55
• /
• 2009

In this paper, we introduce the status of certificate test on crystalline silicon photovoltaic, module in Korea. Up to 5. 2009, about 200 models have passed certificate test under KS C IEC61215 standard. Most products are from Korea, Japan, China. And some are from USA, German and Taiwan. A few environmental test items' results and standard test methods will be discussed. The detail discussion will be shown in the following paper.