• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.114-119
• /
• 2006

High critical current density, high n value, multiple faults endurances, and fast recovery characteristics of YBCO thin films are very attractive characteristics for developing resistive type superconducting fault current limiters. But due to the limited current and voltage ratings of one YBCO module, it is needed to construct series and parallel module connections for high capacity electric networks. Especially for distribution network, more than 30 units should be connected in series to meet voltage level. So in order to construct distribution-level superconducting fault current limiter, simultaneous quench in one YBCO thin films should be realized, and furthermore, quench should be occurred in all fault current limiting units equally to avoid local heating and failures. In this paper, we proposed optimum design of YBCO thin films for fault current limiting module and technical method using shunt resistor to achieve simultaneous quench between multi current limiting units. From the analytical and the experimental results, optimal current path and thickness of shunt material was determined for YBCO thin films and shunt resistor between modules was developed. Finally, 14 kV one phase resistive fault current limiter using multi YBCO thin films was constructed and it was possible to get satisfactory test results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.513-520
• /
• 2018

Since Paris Climate Change Conference in 2015, many policies to reduce the emission of greenhouse gas have been accelerating, which are mainly related to renewable energy resources and micro-grid. Presently, the technology development and demonstration projects are mostly focused on diversifying the power resources by adding wind turbine, photo-voltaic and battery storage system in the island-type small micro-grid. It is expected that the large-scaled micro-grid projects based on the regional district and town/complex city, e.g. the block type micro-grid project in Daegu national industrial complex will proceed in the near future. In this case, the economic cost or the carbon emission can be optimized by the efficient operation of energy mix and the appropriate construction of electric and heat supplying facilities such as cogeneration, renewable energy resources, BESS, thermal storage and the existing heat and electricity supplying networks. However, when planning a large residential town or city, the concrete plan of the energy infrastructure has not been established until the construction plan stage and provided by the individual energy suppliers of water, heat, electricity and gas. So, it is difficult to build the efficient energy portfolio considering the characteristics of town or city. This paper introduces an energy mix optimization(EMO) method to determine the optimal capacity of thermal and electric resources which can be applied in the design stage of the real large-scaled residential town or city, and examines the feasibility of the proposed method by applying the real heat and electricity demand data of large-scale residential towns with thousands of households and by comparing the result of HOMER simulation developed by National Renewable Energy Laboratory(NREL).

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.5
• /
• pp.240-246
• /
• 2006

The mathematical model of the power substation is proposed. The substation esteems as a set of the equipment elements which integrated common connections and electromagnetic field. Some capabilities of model represented by both electric networks and a discrete logical model demonstrated by non-directional graph. The model can be useful for solution of the problem of diagnostic of the high-voltage equipment.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.11 no.1
• /
• pp.15-20
• /
• 2016

Recently, the u-IT applications for plants and livestock become larger and control of livestock farm environment has been used important in the field of industry. We implemented wireless sensor networks and farm environment automatic control system for applying to the breeding barn environment by calculating the THI index. First, we gathered environmental information like livestock object temperature, heart rate and momentum. And we also collected the farm environment data including temperature, humidity and illuminance for calculating the THI index. Then we provide accurate control action roof open and electric fan in of intelligent farm to keep the best state automatically by using collected data. We believed this technology can improve industrial competitiveness through the u-IT based smart integrated management system introduction for industry aversion and dairy industries labor shortages due to hard work and old ageing.

• Journal of the Society of Disaster Information
• /
• v.4 no.1
• /
• pp.34-52
• /
• 2008

The result of all terrors causes enormous damage. In order to prevent this damage in advance and find a prompt provision after terror, we investigated a safety measure against terror on the assumption that the fire in Daegu central subway is a subway terror. The followings are the safety measures against terror based on an underground space. Frist, training systems have to be established to provide against a terror. Second, People's consciousness about safety from a terror, centering on early education, has to be raised. Third, the provisions related with underground tunnel have to be established so that people can take shelter in underground tunnel areas. Fourth, CCTV has to be established in the guest rooms of the electric motor cars. Last, cooperative systems among related organizations have to be constructed, and the networks of the organizations have to be established so that they can cope with an accident.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.2
• /
• pp.156-161
• /
• 1997

In this thesis, based on Genetic Algorithm, a new route search algorithm is presented to search an optimal route between the origin and the destination in intelligent route guidance systems in order to minimize the route traveling time. The proposed algorithm is effectively employed to complex road networks which have diverse turn constrains, time-delay constraints due to cross signals, and stochastic traffic volume. The algorithm is also shown to significantly promote search efficiency by changing the population size of path individuals that exist in each generation through the concept of age and lifetime to each path individual. A virtual road-traffic network with various turn constraints and traffic volume is simulated, where the suggested algorithm promptly produces not only an optimal route to minimize the route cost but also the estimated travel time for any pair of the origin and the destination, while effectively avoiding turn constraints and traffic jam.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2143-2146
• /
• 2003

We propose, for the first time to our knowledge, a novel gain-clamping method for EDFA in WDM Add/Drop networks by introducing a disturbance observer technique. The proposed gain-clamping control input consists of the nominal gain-clamping control such as PI(Proportional and Integral) control and the additional control input for the compensation of the effects caused by channel add/drops. The additional control input is designed using the wellknown disturbance observer technique and can be implemented very easily with general electric elements. We proved the superiority of the new technique over the previous methods by showing simulation result of minimized dips and spikes that appear in power profile of EDFA output.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.495-501
• /
• 2017

The introduction of smart grid, which is an innovative application of digital processing and communications to the power grid, might lead to more and more cyber threats originated from IT systems. In other words, The Energy Management System (EMS) and other communication networks interact with the power system on a real time basis, so it is important to understand the interaction between two layers to protect the power system from potential cyber threats. This paper aims to identify and clarify the cyber security risks and their interaction with the power system in Smart Grid. In this study, the optimal power flow (OPF) and Power Flow Tracing are used to assess the interaction between the EMS and the power system. Through OPF and Power Flow Tracing based analysis, the physical and economic impacts from potential cyber threats are assessed, and thereby the quantitative risks are measured in a monetary unit.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.4 no.1
• /
• pp.84-89
• /
• 2004

The machine cell formation problem is the problem to group machines into machine families and parts into part families so as to minimize bottleneck machines, exceptional parts, and inter-cell part movements in cellular manufacturing systems and flexible manufacturing systems. This paper proposes a new machine cell formation method based on the adaptive Hamming net which is a kind of neural network model. To show the applicability of the proposed method, it presents some experiment results and compares the method with other cell formation methods. From the experiments, we observed that the proposed method could produce good cells for the machine cell formation problem.

• Proceedings of the KIEE Conference
• /
• 2007.11b
• /
• pp.291-293
• /
• 2007

SCADA (Supervisory Control and Data Acquisition) SCADA refers to the combination of telemetry and data acquisition [1]. SCADA system has been used for remote measurement and control on the critical infrastructures as well as modem industrial facilities. Electric Power system is a representative system using SCADA network for its communication. Integration between many networks and increasing threatens of terrorism have made the potential risk by cyber attacks real and bigger in power system. Recently, many researching efforts have been made on SCADA network for improving its security. In general aspect, there are already several ways to secure the system like encryption, firewall, authentication, etc. In this paper, we focus on symmetric encryption method and propose the proper key distribution method to reflect the unique characteristics of SCADA network communication.