• 공업화학
• /
• 제25권5호
• /
• pp.548-551
• /
• 2014

기존 유기 세정제의 문제점인 인체 독성을 낮추기 위하여 생분해도 및 $LD_{50}$가 향상된 에테르 및 에스테르 작용기를 동시에 갖는 세정제 4종을 새롭게 합성하였다. 합성한 세정제를 한국기계전기전자시험연구원에서 국가산업표준 방법으로 분석하여 물리적인 성질과 생분해도 및 $LD_{50}$을 측정하고 세정성 평가를 수행하였다. 물성 측정 결과, 물리화학적 성질이 세정제로서 적합한 것으로 확인되었다. 세정력 평가를 위하여 $60{\times}40mm$ 크기의 스테인리스 강 기판에 절삭유, 방청유, 인발유, 윤활유를 각각 기판에 도포하여 합성한 세정제(1-4)에 침적하여 세정력을 평가하였다. 최대 5 min 간 침적하였을 때 절삭유는 96-100%, 방청유에서는 64-72%, 인발유는 59-88%, 윤활유는 72-84% 정도의 높은 세정력을 보였다. 또한 세정제(1-4)의 생분해도 99% 이상, $LD_{50}$ 2,000 mg/kg 이상의 값을 보임으로서 인체에 거의 해가 없는 친환경 세정제임을 확인하였다.

• 대한기계학회논문집B
• /
• 제36권6호
• /
• pp.593-600
• /
• 2012

대형 선박의 추진용 디젤엔진에서 버려지는 배기가스의 열을 회수하기 위한 랭킨사이클이 적용된 발전시스템에 대하여 R245fa 및 water의 작동유체에 따른 그 엑서지 특성을 분석하였다. 그 이론적인 계산 결과로, R245fa에 대하여 터빈입구의 압력이 증가할수록 엑서지 효율 및 시스템의 엑서지 효율이 증가하였고, 엑서지 파괴율은 주로 응축기 및 증발기에서 상대적으로 높게 나타났다. 그리고 질량유량의 증가에 따라 시스템의 엑서지 효율이 증가하는 특성을 보였다. Water의 경우에, 증발기에서의 엑서지 파괴율은 R245fa의 경우와 유사하게 나타났지만, 터빈입구의 압력 및 질량유량 비율의 변동에 대하여 열원에 대한 엑서지 손실률이 가장 큰 폭으로 변동하였다.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.278-286
• /
• 1999

To predict the behavior of the intravascular micro active endoscope in the real human vascular system, a human mock circulation system was developed. The intravascular micro active endoscope which consists of micro active bending catheter and micro drug infusion catheter was driven in the velocity, Re number and temperature controlled flow. The three SMA (Shape Memory Alloy) zigzag type spring in the micro active bending catheter was heated by the electric current generated by PWM controller, and the shape memory effect made the actuator bend to any direction. The micro drug infusion catheter was driven through the inner hole of the micro active bending catheter. A mock circulation system is shaped from Ascending Arota to Femoral artery according to a human data (the data contains many vascular sizes and hydrographs of many control points). We developed a vascular model with glass and silicone tubes, and set the flow system with circulation parts, flow settling parts, and lots of valves. The heater and heat-controller was added to the How system to centre! the temperature of the How at 36.5$^{\circ}C$. The result showed that the developed intravascular micro active endoscope could be induced to any point in the vascular model.

• Journal of Biosystems Engineering
• /
• 제26권3호
• /
• pp.263-270
• /
• 2001

This study was conducted in order to develop wind-water heating system where frictional heat is creased between the rotor and working fluid when they are rotating in the cylindrical heat generator. The wind-water heating system is composed of rotor, stator, working fluid, motor, inverter and heat generation tank. Instead of wind turbine, we have used an electrical motor of 30㎾ to rotate the rotor in this system. Two working fluids and six levels of rotor rpm were tested to quantify heat amounts generated by the system. Generally, as motor rpm goes up heat amount increases that we have expected. At the same rpm, viscous fluid showed up better performance than the water, generating more heat by 10$\^{C}$ difference. The greatest heat amount of 31,500kJ/h was obtained when the system constantly drained out the hot water of at the flow rate of 500ℓ/h. Power consumption rate of the motor was measured by thee phase electric power meter where the largest power consumption rate was 14㎾ when motor rpm was 600 and gained heat was 31,500kJ/h, that indicated total thermal efficiency of the wind power water heating system was 62%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.353-356
• /
• 2009

A pivotal mechanical balance of plant for 75kW class molten carbonate fuel cells comprise of a catalytic burner and an ejector which has been designed and tested in KEPRI(Korea Electric Power Research Institute). The catalytic burner, which oxidizes residual fuel in the anode tail gas, was operated at several conditions. Some problems arose due to local overheating or auto-ignition, which could limit the catalyst life. The catalytic burner was designed by considering both gas mixing and gas velocity. Test results showed that the temperature distribution is very uniform. In addition, an ejector is a fluid machinery to be utilized for mixing fluids, maintaining vacuum, and transporting them. The ejector is placed at mixing point between the anode off gas and the cathode off gas or the fresh air Several ejectors were designed and tested to form a suction on the fuel tail gas and balance the differential pressures between anode and cathode over a range of operating conditions. The tests showed that the design of the nozzle and throat played an important role in balancing the anode tail and cathode inlet gas pressures. The 75kW MCFC system built in our ejector and catalytic burner was successfully operated from Novembe, 2008 to April, 2009. It recorded the voltage of 104V at the current of 754A and reached the maximum generating power of 78.5kW DC. The results for both stand-alone and integration into another balance of plant are discussed.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.313-320
• /
• 2006

The present study is to analyze the thermoelectric properties of $Bi_{0.4}Sb_{1.6}Te_3$ thermoelectric materials fabricated by the mechanical grinding process. The $Bi_{0.4}Sb_{1.6}Te_3$ powders were prepared by the combination of mechanical milling and reduction treating methods using simply crushed pre-alloyed $Bi_{0.4}Sb_{1.6}Te_3$ powder. The mechanical milling was carried out using the tumbler-ball mill and planetary ball mill. The tumbler-ball milling had an effect on the carrier mobility rather than the carrier concentration, whereas, the latter on the carrier concentration. The specific electric resistivity and Seebeck coefficient decreased with increasing the reduction-heat-treatment time. The thermal conductivity continuously increased with increasing the reduction-heat-treatment time. The figure of merit of the $Bi_{0.4}Sb_{1.6}Te_3$ sintered body prepared by the mechanical grinding process showed higher value than one of the sintered body of the simply crushed powder.

• Journal of Biosystems Engineering
• /
• 제34권6호
• /
• pp.391-396
• /
• 2009

The percentage of those aged 60 and over is 43.5% among our country's 3,186 thousands farming population, so farm village is getting aging society rapidly. Moreover agricultural competitiveness has being weakened due to labor shortage by degradation in quality of labor configuration from elderly porson. For realisms easy workability, we developed a motor vehicle for agricultural activity. The vehicle has an automatic guidance system which could follows a track of magnetic tape on the floor for easy moving to given working position. We collected data from two guidance sensors, located on front and rear end of the vehicle and calculated displacement and angle deviation from the track. This traveling system was stably controlled with processing information deflection S, angle of deviation, D and angle velocity, Vt = $k_1D$ - $k_2S$ from two guidance sensors attached on front and rear of th motor vehicle. Also this system have been tested under various condition of $k_1$, $k_2$ for comparison on both stepped and turning routes. The results show that traveling performance is best at $k_1$=0.7, $k_2$=3.

• 기술사
• /
• 제15권4호
• /
• pp.12-24
• /
• 1982

East Parts of Bangladesh have been benifited by low cost energy generated by domestic natural gas but West parts where energy generated by imported fuel. Bangladesh Government authority has very much concerned to transmit the low cost electricity to the West from the East for past several years. To solve such concerns, cross-country 230kv double circuits Power transmission line was proposed, however there was a big obstacle for the realization of this line to cross the Jamuna river which has 12 km long width with a deep muddy river bed. A consultant engineering firm named Merz-Mclellan anyway finalized this plan and a world-wide bid was announced on June 31, 1979. Due to the expected difficulty to construct the towers on sea like area, only three construction groups have participated. including a Korean joint venture organization of Samsung-Korean Developement corporation-Kolon Electric Machinery company. After 3 months bid evaluation, contract was awarded to Korean Consosium and KEM Co was in charge of designing steel towers with anchor bolts and base plates beside to electrical engineering field. Then KEM Co have faced and over-comed many unenpected technical difficulties such as forced eccentricity joint on base plate, distorsion issue of 60mm thick plates welding, threading anchor bolts, tad heat treatment of some anchor bolts, disagreement from Consultant Engineer on multiplying factor of leg stresses for 45$^{\circ}$ wind and on reducing O.L.F for wind loads on cables for such 1220km long spans. After spending two years long period for designing and engineering towers, base plates, and anchor bolts, first shipment of tower was finally realized on Nov. 8, 1981 and on the other hand KDD has proceeded concrete caisson work on schedule at Jamuna river site and expected to complete tower erection and stringing of cables within this year of 1982 which was original completion target.

• 대한기계학회논문집B
• /
• 제36권9호
• /
• pp.937-944
• /
• 2012

선박의 주 추진용 디젤엔진에서 배출되는 배기가스의 폐열을 회수하는 발전시스템에 대하여, 작동유체로서 물이 적용된 3 변 사이클에 대한 열역학적 특성을 이론적으로 조사하였다. 그 결과로, 하나의 열원이 주어지면, 에너지 및 엑서지 효율은 터빈입구에서 작동유체에 대한 압력 및 온도의 특정한 조건에 의하여 최대화될 수 있었다. 그러한 조건에 대하여 응축온도의 증가에 따라, 터빈의 체적 팽창비를 적절하게 감소시킬 수 있었는데, 열원의 엑서지 손실률 및 응축기에서 엑서지 파괴율이 크게 증가되었다. 따라서, 상부 사이클에서 버려지는 엑서지를 회수하기 위하여, 저온 열원에 적합한 유기랭킨사이클을 하부 사이클로 적용하는 복합 사이클이 유용할 수 있다.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2013년도 특별논문집
• /
• pp.30-34
• /
• 2013

Prevention of exhaust gas back flow becomes a great interest to shipyards and shipowners in large container carriers because exhaust gas pollutes cargoes, flows back into the deck house and the engine room area through fresh air intakes and fan rooms, gives harmful damages to the crew's health and also gives thermal damages to electric equipments on the navigation deck. The phenomena of exhaust gas back flow has been studied with the analysis of sea trial records and wind tunnel tests and the height of the exhaust gas pipe, the front area of the deck house, the inflow speed and the position of the radar mast platform has been confirmed as the principal factors of exhaust gas back flow phenomena. The simple empirical formula to estimate exhaust gas back flow phenomena and the design guidances of exhaust gas related structures on deck has been introduced. In future, parametric studies for the exhaust gas back flow factors will be carried out with the CFD analysis. The results of this study will be the guide for development of the prevention method of exhaust gas back flow phenomena for large container carriers.