• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.43-47
• /
• 2000

Oil seals will experience a small amplitude dynamic excitation due to the shaft eccentricity as well as out-of-roundness of the shaft. The direct integration method is selected to analyze the time domain response of the seal lip-shaft contact. The physical properties of rubber seal materials are experimentally analyzed. Effects of both frequency and temperature on the material stiffness behavior are investigated for the linear viscoelastic materials of the seal. Using the nonlinear transient model, a finite element analysis of the lip-shaft contact behaviors under dynamic conditions is presented as a function of the shaft eccentricity, the shaft interference and the garter spring stiffness. The FEM results based on the experimental data indicate that the increased rotating speed may produce the separation conditions. These results will be very useful in predicting the leakage of oil seals under dynamic conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.895-902
• /
• 1999

This paper deals with a numerical study of the tribological contact stress distributions of elastomeric lip seals for oscillating shafts when the sealing interference and band width between the lip ease or contact seals and the shaft are present. Using the finite element method the contact stress and band width of scraper seals are analyzed for the sealing interference including some nonlinearities such as geometrical nonlinearity, material nonlinearity and nonlinear contact boundary condition. The FEM results showed that the contact stress concentrated on the contacting lip zone between the contacting edge of lip and the shaft for the increased interference. In double lip scraper seals, ole maximum contact stress of the dust lip, which is used to exclude foreign contaminants is six times higher than that of the primary sealing lip, which is used to contain lubricants.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.198-203
• /
• 1997

This paper deals with a numerical study of the tribological contact stress distributions of elastomeric lip seah for oscillating shafts when the sealing interference and band width between the lip edge of contact seals the shaft are present. Using the finite element method, the contact stress and band width of scraper seals rare analyzed for the sealing interference including some nonlinearities such as geometrical nonlinearity, material nonlinearity and nonlinear contact boundary condition. The FEM results showed that the contact stress concentrated on the contacting lip zone between the contacting edge of lip and the shaft for the increased interference. In double lip scraper seals, the maximum contact stress of the dust lip, which is used to exclude foreign contaminants, is six times higher than that of the primary sealing lip, which is used to contain lubricants.

• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.34-37
• /
• 2011

This paper presents sealing contact stress and deformation behaviors of an elastomeric contact seal for a pipe connection. In this study, a pipe connection is used by a joint nut and an elastomeric contact seal with a sealing interference of 0.2~0.5mm. A sealing interference in which compresses an elastomeric contact seal is generated by fastening a joint nut between two pipes. The FEM computed results show that the contact normal stress of contact model 1 with an inclined sealing surface is 1.5~1.75 times high in compared with that of contact model 2 with a parallel sealing surface. This indicates that the sealing contact surface recommends a wedge contact mode between two pipe connections for a high sealing compression stress.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.86-93
• /
• 2009

Elastomeric O-rings have been the most common seals due to their excellent sealing capacity, and availability in costs and sizes. One of the critical applications of O-ring seals is solid rocket motor joint seal where the operating hot gas must be sealed during the combustion. This has long been a design issue to avoid the system failure. For laterally constrained, squeezed and pressurized condition, deformed shape of O-ring was measured by computed tomography method and CCD laser sensor, compared with numerical calculations. As clearance gap changes, sealing performance had been evaluated on peak contact stresses at top, bottom and side contact surfaces. As clearance gap increases, peak contact stresses and contact widths in top and side contact surfaces increase, and the asymmetry of stress distributions is promoted due to pressure increase. It is suggested that peak stress of bottom contact surface can be approximated by simple superposition of peak ones due to squeeze and pressure. Under pressurized condition, sealing performance is dependent on not peak stresses of bottom and side contact surfaces but that of top.

• Journal of the Korean Society of Safety
• /
• v.22 no.5
• /
• pp.13-20
• /
• 2007

Elastomeric O-ring seals are widely used in static and dynamic applications. A compressed and highly pressurized O-ring seal inserted under laterally one-sided constrained condition has been analyzed experimentally and numerically. The deformed shape and extrusion length of the O-ring under high pressure has been measured by the computed tomography. Through the comparison of experimental and FE results, the numerical analysis technique has been verified. Using verified FE method, the contact stress profiles at sealing surfaces have been investigated and their relevance to the 0-ring performance evaluated based on stress-related and displacement-related parameters. It has been found that the contact stress profiles and deformation behaviors of the seal are affected by friction coefficient, gap clearance, and pressure considerably.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.161-166
• /
• 2010

Elastomeric seals are widely used in dynamic seal applications, and it is well known that the sealing surfaces can be gradually worn out. Abrasive wear is known to be the most dominant factor; however, little research has been carried out on this problem until now. In this study, a new contact problem related to elastomeric seals-a small spherical particle and steel surface-was modeled and analyzed using MARC. Variations of von-Mises and residual stress distributions as well as deformed seal and steel surface shapes with seal materials and interferences are presented. The stress distribution and surface deformation are highly affected by the elastic properties of seal. For PTFE, the maximum von-Mises stress exceeds the yield strength, and plastic deformation occurs on the steel surface. Therefore, the sealing surface can also be worn down by sub-surface fatigue due to intervening hard particles in the sealing surfaces together with the well-known abrasion.

• Journal of Drive and Control
• /
• v.9 no.1
• /
• pp.18-24
• /
• 2012

The paper deals with the design of a new low-friction seal for a pneumatic cylinder with high speed actuation. The seal performance with variation of the cross sections in piston seals with elastomeric material was investigated to minimize the friction forces using ABAQUS. The contact stress and strain distributions and frictional forces of the piston seals were investigated with variation of interference fits, supply pressures and friction coefficients. To develop adequate and productive procedures, the finite element models of the piston seals were created and nonlinear analysis of a seal design was conducted in order to build further knowledge and understanding of the seal's performance characteristics.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.3
• /
• pp.21-26
• /
• 2011

Nonlinear seal friction in pneumatic cylinders can impede the performance of pneumatic systems designed for high precision positioning with favorable high speed actuation. The behaviour of an elastomeric piston seals in high speed pneumatic cylinders is analyzed by nonlinear finite element analysis using ABAQUS. The contact pressures, stress and strain distributions and frictional forces of the squeeze type piston seal are simulated with variation of the seal radial installed interference, the operating pressures, friction coefficients and piston rod velocities. The nonlinear finite element model of the squeeze type piston seal is used to predict deformation of a seal, friction force and contact pressure distributions.

• Journal of the Korean Society of Safety
• /
• v.22 no.6
• /
• pp.27-34
• /
• 2007

Static or dynamic elastomeric O-ring seals are installed between joining parts, and play key roles of high pressure-tightening. Sealing performance and structural safety of the O-ring are dependent on groove design, plain diameter, squeeze and applications such as pressure and temperature. In this study, to solve O-ring problem squeezed and highly pressurized under laterally one-sided constrained condition, hyperelastic FE analyses are performed, and FE results are compared with measured ones by computer-aided tomography, deformed shape and extrusion depth of the O-ring. Through the comparisons, FE analysis technique was verified. In order to evaluate design sensitivity, Taguchi method was used to select FE analysis cases. Adjustment parameters are clearance gap, groove comer radius, plain diameter and squeeze. By means of verified FE analysis technique, it has been analysed how the parameters have effects on contact stress fields, internal stress fields, and extrusion depths. Sealing performance has been evaluated based on contact stress fields and contact widths, and structural safety on internal stress and strain, extrusion lengths.