• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.155-160
• /
• 1998

The strength design actually carries an inconsistency where the structural analysis is being viewed in terms of elastic while the design is being drawn up in terms of plastic. In this study, in order to extend the applicability of the strength design, MRFEA(Moment Redistribution Finite Element Analysis) is developed. After carrying out the application example, it is found the use of materials was reduced compared to the elastic analysis.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.603-608
• /
• 2008

It is well known that the topology optimization for plastic problem is not easy since the iterative analyses to evaluate the objective and cost function with respect to the design variation are very time-consuming. The finite element limit analysis is an efficient tool which is possible to predict collapse modes and sequential collapse loads of a structure considering not only large deformation but also plastic material behavior with moderate computing cost. In this paper, the optimum topology of a structure considering large and plastic deformation is obtained using the finite element limit analysis. To verify the constructed optimization code, topology optimizations of some typical problems are performed and the optimal topologies by elastic design and plastic design are compared.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.436-442
• /
• 2004

Elastic and plastic deformation behaviors of the high purity aluminum and the silica glass were studied using nanoindentation and finite element analysis(FEA) techniques. Berkovich- and cone-type indenters were used for the nanoindentation test. Deformation behaviors and nanoindent profiles of elastic, elastic-plastic or plastic materials were clearly visualized by FEA simulation. Effects of the penetration depth and strain hardening on the deformation behavior were examined. Pile-up and sink-in behaviors were studied by using FEA technique. Degree of pile-up or sink-in was found to be a function of the ratio of elastic modulus to yield strength of materials. FEA was found to be an effective method to study deformation behaviors of materials under nanoindentation, especially in the case when pile-up or sink-in phenomena occurred.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.51-59
• /
• 1998

The purposes of the paper are to consider the failure phenomenon based on delamination and crack when the encapsulant of plastic IC package under hygrothermal loading in the IR soldering process is on elastic and viscoelastic behavior due to the temperature and to show the optimum design using fracture mechanics. The model for analysis is the plastic SOJ package with a dimpled diepad. The package model with the perfect delamination between chip and diepad is chosen to estimate the resistance to fracture by calculating J-integrals in low temperature and C(t)-integrals in high temperature with the change of the design under hygrothermal loading. The optimum design to depress the delamination and crack in the plastic IC package is presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1257-1264
• /
• 2014

Efforts are presently underway for developing an optimal design methodology for GEN-IV nuclear reactors based on target failure probabilities. A typical example is the system-based code, in which the results are represented in the form of partial safety factors (PSFs). Thus, a PSF is one of the crucial elements in either component design or integrity assessment based on target failure probabilities during the operation period. In the present study, a procedure for calculating the PSF of a circumferential through-wall cracked pipe based on the elastic-plastic crack initiation criterion is established, in which the importance of each input variable is assessed. Elastic-plastic J-integrals are calculated using the GE/EPRI and reference stress methods, and the PSF values are calculated using both first- and second-order reliability methods. Moreover, the effect of statistical distributions of assessment variables on the PSF is also evaluated.

• Nuclear Engineering and Technology
• /
• v.53 no.3
• /
• pp.988-1003
• /
• 2021

Existing elastic analysis methods cannot be adhered to in order to assess the structural integrity of a reactor vessel and internals for a beyond design basis earthquake. Elasto-plastic analysis methods are required, and the factors that affect the elasto-plastic behavior of reactor materials should be taken into account. In this study, a material behavior model was developed that considers the irradiation embrittlement effect, which affects the elasto-plastic behavior of the reactor material. This was used to perform the elasto-plastic time history analyses of the reactor vessel and its internals for beyond design basis earthquake. For this investigation, appropriate beyond design basis earthquakes and reliable finite element models were used. Based on the analysis results, consideration was given to the load reduction effect and the margin change. These were transferred to the internals due to the plastic deformation of the reactor vessel.

• Structural Engineering and Mechanics
• /
• v.4 no.1
• /
• pp.25-35
• /
• 1996

This paper describes a continuum variational formulation for design optimization of nonlinear structures in the elastic-plastic domain, where unloading and reloading of the structures are allowed to occur. The Total Lagrangian procedure is used for the description of the structural deformation. The direct differentiation approach is used to derive the sensitivities of the various structural response measures with respect to the design parameters. Since the material goes into the inelastic range and unloading and reloading of the structure are allowed to occur, the structural response is path dependent and an additional step is needed to integrate the constitutive equations. It can be shown, consequently, that design sensitivity analysis is also path-dependent. The theory has been discretized by the finite element technique and implemented in a structural analysis code. Mathematical programming approach is used for the optimization process. Numerical applications on trusses are performed, where cross-sectional areas and nodal point coordinates are treated as design variables. Optimal designs have been obtained and compared by using two different strategies: a two level strategy where the levels are defined accordingly the type of design variables, cross sectional areas or node coordinates, and optimizing simultaneously with respect to both types of design variables.

• Tunnel and Underground Space
• /
• v.2 no.1
• /
• pp.152-163
• /
• 1992

The study of rock mass behaviour through a numerical analysis is important for the design, construction and maintenance of large rock caverns. The objectives of the numerical analysis are to design reasonably and construct safely the underground structures, to maintain them soundly after construction and to extend them securely for a desired period of time. Methods of numerical analyses included in this case study are the finite element method, the boundary element method, and the distinct element method. The numerical models are purely elastic, elastoplastic, visco-elastic, visco-plastic, easto-visco-plastic and jointed-discontinuous materials. The results of this case study indicate that the rock mass behaviour could be predicted exactly through continuous comparisons of the numerical results with the in-situ measurements.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.3 s.21
• /
• pp.131-137
• /
• 2006

This study presents a new stress analysis method to be substituted for the elastic analysis in such a plastic design procedure. This method is accompanied by an efficient mathematical tool which can be easily handled by personal computer. The method also easily accepts arbitrary strategies by the designer for selection member size.

• Structural Engineering and Mechanics
• /
• v.5 no.2
• /
• pp.193-207
• /
• 1997

Experimental tests are described on three ring stiffened machined circular cylinders and three ring stiffened machined circular cones, which were tested to destruction under uniform external pressure. All six vessels failed by inelastic general instability. The experiments showed that the vessels initially deformed plastically at mid-bay in the circumferential direction, and this caused the circumferential tangent modulus to become much less than the elastic Young's modulus, causing the vessels to fail through plastic general instability at pressures much less than that predicted by elastic theory. Based on a thinness ratio, two semi-empirical design charts are provided, which are intended to be used for design purposes in conjunction with the finite element method and a plastic reduction factor.