• 한국지진공학회논문집
• /
• 제11권2호
• /
• pp.47-56
• /
• 2007

본 연구에서는 지진하중을 받는 탄성 및 비탄성 구조물에 대하여 수동 및 준능동 TMD의 지진응답제어성능을 평가하였다. 먼저 기존의 연구에서 제안된 식을 사용하여 최적 설계된 수동형 TMD와 본 연구에서 제시된 준능동 TMB가 설치된 탄성 구조물의 변위스펙트럼을 구하였으며, 준능동 TMD가 TMD보다 작은 스트로크를 가지고도 최대변위응답제어에 있어 우수함을 확인하였다. 또한 구조물의 주기와 TMD의 주기가 일치하지 않은 경우의 성능저하에 대한 TMD의 강인성을 평가하였다. 최종적으로 Bouc-Wen 모델을 사용하여 모사된 비탄성이력 특성을 가지는 구조물에 대한 수치해석을 수행하였으며, 이를 통해 탄성구조물에 대하여 최적화된 수동형 TMD의 성능은 구조물 응답의 비탄성이력 부분이 증가함에 따라 크게 저하되는 반면 준능동 TMD는 수동형 TMD보다 약 15-40% 정도의 더 많은 응답감소효과를 가짐을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.7-14
• /
• 2000

Nowadays, the viscous damper using high viscosity oil was much to be used for engine shafting system to reduce the excessive additional stress by torsional vibration. In general, it was assumed that the viscous damper could be modelled having only damping coefficient, that is to say, whose stiffness be ignored. But it is found that there exists a jump phenomenon, as a kind of non-linear vibration, in the actual engine shafting system with a damper of high viscosity. Therefore the damper ring and the casing are modelled as two mass elastic system with a complex viscosity. Also, to analyze a non-linear phenomenon, it is assumed that the viscous damper has a linear stiffness coefficient in proportion to the angular amplitude and a non-linear stiffness coefficient in proportion to cube of the angular amplitude. For the analysis, Quasi-Newton method with BFGS(Broyden-Fletcher-Goldfarb-Shanno) formula is used. Both calculated and measured values are provided in this paper which confirm the possibility of applying non-linear theory to engine shafting system with viscous damper.

• Steel and Composite Structures
• /
• 제49권3호
• /
• pp.257-270
• /
• 2023

In this study, the feasibility and applicability of a friction damper with a vertical installation scheme are investigated. This device is composed of a steel section and two friction hinges at both ends which dissipate seismic energy. Due to its small width and vertical installation scheme, the proposed damper can minimize the interference with architectural functions. To evaluate the performance of the proposed damper, its mechanical behavior is theoretically evaluated and the required formulas for the yield strength and elastic stiffness are derived. The theoretical formulas are verified by establishing the analytical model of the damper in the SAP2000 software and comparing their results. To further investigate the performance of the developed damper, the provided analytical model is applied to a 4-story reinforced concrete (RC) structure and its performance is evaluated before and after retrofit under the Maximum Considered Earthquake (MCE) hazard level. The seismic performance is thoroughly evaluated in terms of maximum interstory drift ratio, displacement time history, residual displacement, and energy dissipation. The results show that the proposed damper can be efficiently used to protect the structure against seismic loads.

• 한국지진공학회논문집
• /
• 제9권1호통권41호
• /
• pp.9-16
• /
• 2005

본 논문의 목적은 탄성과 비탄성 구조물의 지진응답제어를 위한 마찰감쇠기의 설계절차를 제시하는 것이다. ATC-40과 ATC-55를 이용하여 비탄성 구조물의 등가선형감쇠비와 등가선형주기를 구하였고, 이에 기초하여 목표 성능을 만족하기 위한 마찰감쇠기의 최대마찰력을 결정하는 식을 제시하였다. 이 식은 항복 전후 강성비와 요구되는 탄성강도에 대한 항복강도비, 그리고 구조물의 주기에 따라 비선형 수치해석과 오차가 발생한다. 수식에 의해 산출한 최대마찰력과 비선형 수치 해석에 의해 산출된 값과의 오차를 줄이기 위하여, 최소 제곱법을 사용하여 오차 보정식을 제시하였다. 수치해석결과는 제안된 보정식을 사용하면 탄성 및 비탄성 지진응답제어를 위한 마찰감쇠기의 설계를 합리적으로 수행할 수 있음을 보여준다

• 한국지진공학회논문집
• /
• 제16권2호
• /
• pp.25-33
• /
• 2012

본 연구에서는 내력벽 시스템에 대하여 연결보의 단부에 적용이 가능한 박판형 금속감쇠기의 성능을 실험을 통하여 규명하고자 하였다. 박판형 금속감쇠기의 박판 두께와 길이를 변수로 하여 5개 시험체를 제작하였으며, 층간변위비 5%까지 반복하여 횡력을 가력하였다. 실험결과, 금속 박판에 좌굴발생 후 소성변형이 발생하면서 에너지 발산이 이루어졌으며, 기존의 일반 콘크리트 시험체보다 에너지 발산량이 크게 나타났다. 박판의 길이가 짧을수록 전단내력의 값은 증가하였으나 발산에너지의 양의 증가는 크게 나타나지 않았다. 실험 내력을 탄성좌굴해석과 비교한 결과, 해석에 의한 내력은 내력곡선 선형영역의 최대값을 적절히 예측함을 알 수 있었다.

• Earthquakes and Structures
• /
• 제12권5호
• /
• pp.515-527
• /
• 2017

Recently, Friction dampers become popular due to the desirable performance in the energy dissipation of lateral loads. A lot of research which has been conducted on these dampers results in developing friction dampers with low sensitivity to the number of cycles and temperature increases. Friction dampers impose high residual drifts to the buildings because of low post-yield stiffness of the damper which results from increasing lateral displacement and period of buildings. This issue can be more critical under strong aftershocks which results in increasing of structural damages. In this paper, in addition to the assessment of aftershock on steel buildings equipped with friction dampers, methods for controlling residual drifts and decreasing the costs of retrofitting are investigated. Utilizing rigid connections as a lateral dual system and activating lateral stiffness of gravity columns by adding elastic braces are as an example of effective methods investigated in this research. The results of nonlinear time history analyses on the low to medium rise steel frames equipped with friction dampers illustrate a rise in residual drifts as the result of aftershocks. In addition, the results show that different slip loads of friction damper can affect the residual drifts. Furthermore, elastic stories in comparison to rigid connections can reduce residual drifts of buildings in an effective fashion, when most slip loads of friction dampers are considered.

• 한국소음진동공학회논문집
• /
• 제22권4호
• /
• pp.377-382
• /
• 2012

This paper presents a proof-of-concept study on the evaluation of torsional vibration isolation performance through in-situ output torque measurement by using a non-contacting magneto-elastic torque transducer installed in the vehicle driveline system. The de-trending processing is first conducted to extract the torsional vibration from the measured driveline output torque. In order to estimate the transmissibility, primary performance indicator of a vibration isolator, the magnitude of transmitted torsional vibration with different frequencies is compared. From the conservative estimation results, the torsional damper built in a lock-up clutch of a torque converter is identified to be a vibration isolator. The evaluation results show that the fluid damping by torque converter outperforms the vibration isolation function of a torsional damper, and the isolation performance needs to be enhanced.

• Smart Structures and Systems
• /
• 제26권5호
• /
• pp.619-629
• /
• 2020

Solar towers, which often has a large aspect ratio and low fundamental natural frequency, were extremely prone to large amplitude of wind-induced vibrations, especially Vortex-Induced Vibration (VIV). A tiny Tuned Mass Damper (TMD) with conveniently adjustable eddy current damping was specially designed and manufactured for elastic wind tunnel tests of a solar tower. A series of numerical simulations by using the COMSOL software were conducted to determine three key parameters, including the thickness of the back iron plate and the conductive plate (T_b and T_c), the distance between the magnet and the conductive plate (T_d). Based on the results of numerical simulations, a tiny TMD was manufactured and its structural parameters were experimentally identified. The optimized values of the tiny TMD can be conveniently realized. The tiny TMD was installed at the top of the elastic test model of a 243-meter-high solar tower, and a series of wind tunnel tests were carried out to examine the effectiveness of the TMD in suppressing wind-induced responses of the test model. The results showed that the wind-induced responses could be obviously reduced by the TMD, especially in the cross-wind direction. The cross-wind RMS and peak responses at the critical wind velocity can be reduced by about 86% and 75%, respectively. However, the maximum reduction of the responses at the design wind velocity is about 45%, obviously less than that at the critical wind velocity.

• Earthquakes and Structures
• /
• 제11권6호
• /
• pp.1001-1025
• /
• 2016

Building structures generally have inherent low damping capability and hence are vulnerable to seismic excitations. Control devices therefore play a useful role in providing safety to building structures subject to seismic events. In recent years semi-active dampers have gained considerable attention as structural control devices in the building construction industry. Magneto-rheological (MR) damper, a type of semi-active damper has proven to be effective in seismic mitigation of building structures. MR dampers contain a controllable MR fluid whose rheological properties vary rapidly with the applied magnetic field. Although some research has been carried out on the use of MR dampers in building structures, optimal design of MR damper and combined use of MR and passive dampers for real scale buildings has hardly been investigated. This paper investigates the use of MR dampers and incorporating MR-passive damper combinations in building structures in order to achieve acceptable levels of seismic performance. In order to do so, it first develops the MR damper model by integrating control algorithms commonly used in MR damper modelling. The developed MR damper is then integrated in to the seismically excited structure as a time domain function. Linear and nonlinear structure models are evaluated in real time scenarios. Analyses are conducted to investigate the influence of location and number of devices on the seismic performance of the building structure. The findings of this paper provide information towards the design and construction of earthquake safe buildings with optimally employed MR dampers and MR-passive damper combinations.

• Structural Engineering and Mechanics
• /
• 제17권2호
• /
• pp.187-201
• /
• 2004

A shaking table test on a three-story one-bay steel frame model with metallic yield dampers and their parallel connection with oil dampers is carried out to study the dynamic characteristics and seismic performance of the energy dissipation system. It is found from the test that the combined energy dissipation system has favorable reducing vibration effects on structural displacement, and the structural peak acceleration can not evidently be reduced under small intensity seismic excitations, but in most cases the vibration reduction effect is very good under large intensity seismic excitations. Test results also show that stiffness of the energy dissipation devices should match their damping. Dynamic analysis method and mechanics models of these two dampers are proposed. In the analysis method, the force-displacement relationship of the metallic yield damper is represented by an elastic perfectly plastic model, and the behavior of the oil damper is simulated by a velocity and displacement relative model in which the contributions of the oil damper to the damping force and stiffness of the system are considered. Validity of the analytical model and the method is verified through comparison between the results of the shaking table test and numerical analysis.