• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.5
• /
• pp.573-584
• /
• 2012

Breast and prostate tumors or cancers tend to be stiffer than the surrounding normal tissue. However, the difference in echogenicity between cancerous and normal tissues is not clearly distinguishable in ultrasound B-mode imaging. Thus, imaging the stiffness contrast between the two different tissue types helps to diagnose lesions quantitatively, and such a method of imaging the elasticity of human tissue is termed ultrasound elasticity imaging. Recently, elasticity imaging has become an effective complementary diagnostic modality along with ultrasound B-mode imaging. This paper presents various elasticity imaging methods that have been reported up to now and describes their characteristics and principles of operation.

• Journal of Korean Association for Spatial Structures
• /
• v.18 no.1
• /
• pp.127-134
• /
• 2018

This study suggests the tangent modulus $E_t$ associated with partially yielded section of steel member under axially compressed. The provisions for column strength does not provide a information about failure mode of structural system. So, designers can not evaluate that a failure comes from member buckling or material yielding. The material of the axially compressed column under inelastic behavior reaches yielding point before the axial force renders the column bent. If axial members yields not by buckling effect but gradually yielding effect of material, the design code should accept related tangent modulus Et which is based on gradual yielding effect of material. This study provides the new effective tangent modulus $E_t$ derived in the case that residual stress is 30 percent and 50 percent of yielding stress respectively. The study considers idealized I section of steel which ignores web and general I section of steel with web respectively and makes conclude that tangent modulus $E_t$ with idealized I section of steel is rational.

• Structural Engineering and Mechanics
• /
• v.24 no.6
• /
• pp.727-740
• /
• 2006

A simple plane-strain solution is derived in this paper for the functionally graded multilayered isotropic elastic cylinder under static deformation. The solution is obtained using method of separation of variables and is expressed in terms of the summation of the Fourier series in the circumferential direction. While the solution for order n = 0 corresponds to the axisymmetric deformation, that for n = 2 includes the special deformation frequently utilized in the upper and lower bounds analysis. Numerical results for a three-phase cylinder with a middle functionally graded layer are presented for both axisymmetric (n = 0) and general (n = 2) deformations, under either the traction or displacement boundary conditions on the surface of the layered cylinder. The solution to the general deformation case (n = 2) is further utilized for the first time to find the upper and lower bounds of the effective shear modulus of the layered cylinder with a functionally graded middle layer. These results could be useful in the future study of cylindrical composites where FGMs and/or multilayers are involved.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.457-465
• /
• 2001

Shrinkage strains of concrete slab in multi-story building are restrained by structural members such as columns or walls, then can induce cracks due to excessive shrinkage stress over tensile strength of member. In this study, a shrinkage stress analysis method of concrete slab in multi-story building considering not only material properties such as shrinkage, creep and reinforcement effect but also construction sequence is proposed. Tensile stresses of slab due to shrinkage are calculated by converting shrinkage strains into equivalent temperature gradients, creep that can release shrinkage stress can be considered by replacing the modulus of elasticity of concrete, Ec , to the effective secant modulus of elasticity of concrete, E$\_$eff/ Reinforcements are also considered by modeling them as equivalent beam elements in FEM program. Results of step by step analysis reflecting construction sequence summed up to calculate stresses of the whole building considering that shrinkage stresses of the building come from the difference of shrinkage between i-th floor and (i-1)-th floor, named as effecitive shrinkage, and it can be varied by construction sequence. The results of 10-story example building show that shrinkage stresses of lower floors are greater than those of upper floors, that is, stresses of lower floors(1∼2FI.) exceed modulus of rupture of concrete, but stress ratios of higher floors are in the range of 27.9∼92.8%.

• Advances in concrete construction
• /
• v.6 no.4
• /
• pp.363-373
• /
• 2018

Portland cement pervious concrete (PCPC) is an effective pavement material to solve or reduce the urban waterlogging problems. The Mechanical properties, the permeability, the abrasion resistance and the frost resistance of PCPC without fine aggregate were investigated. The increase of porosity was achieved by fixing the dosage of coarse aggregate and reducing the amount of cement paste. The results show that the compressive strength and the flexural strength of PCPC decrease with the increase of porosity. The permeability coefficient and the wear loss of PCPC increase with the increase of the porosity. The compressive strength and the flexural strength of PCPC subjected to 25 freeze-thaw cycles are reduced by 13.7%-17.8% and 10.6%-18.3%, respectively. For PCPC subjected to the same freeze-thaw cycles, the mass loss firstly increases and then decreases with the increase of the porosity. The relative dynamic modulus elasticity decreases with the increase of freeze-thaw cycles. And the lower the PCPC porosity is, the more obvious the dynamic modulus elasticity decreases.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Advances in nano research
• /
• v.16 no.3
• /
• pp.303-311
• /
• 2024

This paper conducts a thorough economic evaluation of integrating nanoparticles into concrete structures within the construction industry, aiming to elevate the material properties of concrete. Employing the Halpin-Tsai micromechanics theory for deriving the effective material properties of the nanocomposite concrete structure, the research investigates the nuanced impact of nanoparticles on various mechanical properties, including the modulus of elasticity, compressive strength, and their indirect effects on the percentage of reinforcement. Implementing the Euler theory to formulate the governing equation based on Hamilton's principle, the study delves into the pricing dynamics of nanoparticles and their influence on the overall cost structure of concrete structures. Notably, the findings reveal that a measured increase in the volume percentage of nanoparticles, up to 1%, results in a remarkable 78% improvement in elastic modulus and a substantial 142% reduction in armature percentage. Remarkably, from an economic perspective, the incremental cost associated with the integration of nanoparticles is relatively modest (around $1 per ton of concrete), considering the substantial enhancements in mechanical properties achieved.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.1
• /
• pp.21-26
• /
• 2009

This study was performed to evaluate the physical and mechanical properties of concrete using waste activated carbon. Materials used were ordinary portlant cement, crushed coarse aggregate, natural fine aggregate, waste activated carbon, and superplasticizer. The substitution ratios of waste activated carbon were 0,1,2,3,4,5,6,7,8,9 and 10%. The unit weight was decreased and water absorption ratio was increased with increasing the waste activated carbon content, respectively. When the substitution ratio of waste activated carbon was 3%, compressive strength, flexural strength and dynamic modulus of elastisity were more higher than that of the ordinary portland cement (OPC), and it was decreased with increasing the waste activated carbon content, respectively. The most effective contents of waste activated carbon was 2% in performance and 4% in practical use Accordingly, waste activated carbon can be used for concrete material.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.831-835
• /
• 2008

Recently, the use of C.S.G is gradually increasing as the construction material for dam, road, revetment and so on. The strength characteristics of C.S.G is affected by various influence factors such as specimen size, maximum grain size and water contents. Therefore, When designing and constructing the C.S.G structure, it is very important for us to understand the nature of used materials well and to test it's quality. Commonly, C.S.G strength test is used the cylinders specimen size of $15{\times}30$ at KS F2405. But, the specimen size extracted from the field structure is not regular. This paper aims at offering the experimental data about the compressive strength and elasticity modulus by change of the specimen size for the effective quality control of the C.S.G structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.129-132
• /
• 2006

It is generally reported that most of RC beams strengthened with simply bonded FRP composite is failed by FRP debonding. Also, the flexural performance of RC member strengthened with FRP composite can be calculated using the effective strain of FRP. The effective strain as a result of the debonding failure depends on many variables, such as FRP stiffness including the thickness($t_f$) and modulus of elasticity($E_f$), the amount of FRP but the FRP stiffness is reportedly the most influential. The purpose of this paper, therefore, is to examine effects of FRP stiffness on the flexural strengthening of RC beams. 4 different stiffness of CFRP composite including CFRP sheet and laminae were selected. From the tests, it was found that the flexural performance of RC beams strengthened with CFRP composite can be calculated based on the effective strain of the CFRP composite and the effective strain is inversely proportional to the CFRP stiffness.