• Journal of ILASS-Korea
• /
• v.5 no.2
• /
• pp.68-74
• /
• 2000

A this experimental study is executed to analyze spray characteristics for air-shrouded injector and 4hole 2spray type injector used in a gasoline engine. Since spray parameters including spray penetration and angle, SMD, and atomization characteristics are very important to increase the engine performance, the image processing algorithm for measuring the non-spherical spray diameter is developed. Spray characteristics of the air-shrouded injector(2hole 2spray) and 4hole-2spray injector are analyzed respectively by this digital image processing method. Effective spray characteristics to injectors is derived from this experimentation and obtained the design guide for gasoline injector.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.3 no.1
• /
• pp.12-17
• /
• 1966

A more extensive theoretical analysis for a ferrite filled electromagnetic delay line of two coaxial anisotropic conducting cylinders was made and improvements of the delay line n=0 mode operation was achieved by separating effective sections using short-circuited coils to eliminate unnecessary couplings among windings of different phase. Time delay of order of 10 microseconds per meter in video frequency range was observed from 3"/8 diameter 6" long delay line tilled with ferrite material. Design formula was presented with illustrative discussions to help design for practical purposes. purposes.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.410-415
• /
• 2001

Conventional Korean tunnel portals require a lot of overburden as, fer static reasons, about 1.5 to 2.0 times the tunnel diameter is needed for the height in order to achieve a sufficient arching effect. Thus, considerable movement of earth and support constructions are required which lead to undesirably large changes of and damage to the environment. With a massively designed pipe roof, tunnels with little overburden can be built. For the effective construction of a pipe roof as an advancing safeguarding method, the following properties are indispensable： stability, insensitivity to settling and drilling accuracy. With the AT casing system a new pipe roof method has been developed which on the one hand entirely combines the properties mentioned last, and which on the other hand permits safe, economical and environmentally friendly construction of tunnels at low overburden heights of 3 to 6 m.

• Plant Journal
• /
• v.7 no.3
• /
• pp.65-73
• /
• 2011

This research has suggested a method to select pipe wall thickness by application of the value engineering to reduce the cost and quantity that are major part of construction materials. This research shows that the application of value engineering reduces the cost of piping materials by optimizing pipe wall thickness while maintaining process flow date of design pressure and design temperature. Based on this knowledge, the application of the value engineering will lead to the cost reduction and quantity reduction by effective selection of pipe wall thickness. The application of the value engineering will help the EPC companies to win a contract in the overseas plant market.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.5
• /
• pp.76-86
• /
• 2007

For the purpose of ground improvement by means of soil flushing systems. Incorporated technique with prefabricated vertical drains have been used for dewatering from fine-grained soils. The laboratory model tests were performed by using the flushing tracer solutions for silty soils and recorded the tracer concentration changes with the elapsed time and flow rates. A mathematical model for prediction of contaminant transport using the PVD technology has been developed. The clean-up times for the predictions on both soil condition indicate more of a sensitivity to the dispersivity parameter than to the extracted flow rate and vertical velocity parameters. Based on the results of the analyses, numerical analysis indicate that the most important factor to the in-situ soil remediation in prefabricated vertical drain system is the effective diameter of contaminated soil.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.146-153
• /
• 1993

Thd specimens were melited in high frequency induction furnace. The samples for measurements were prepared by machining cylinder of 9.5mm diameter and 15mm height. These samples were then hot-pressed according to strain rate ( .epsilon. ). These samples were decanned and cut out, and subsequently heat treated at 1000 .deg. C for 4hours. These were investigated for the change of microstructure, domain pattern, X-ray diffraction and magnetic properties. The stress distributions in the specimens during compressing process were calculated by a finite element method program(SPID). The calculated stresses were effective stress( .sigma. $_{eff}$), compressive direction stress( .sigma. $_{z}$), and shear stress( .tau. $_{rz}$ ). These stresses were compared with the experimental data.a.a.

• Radiation Oncology Journal
• /
• v.2 no.1
• /
• pp.21-23
• /
• 1984

Temperature homogeniety and stationary temperature is the most important thermometric considerations for the clinical use of hyperthermia. A thermal mapping was done in a phantom with thermocouple during hyperthermia which was induced by 1.0MHz,$0.7\~0.8watts/cm^2$ ultrasound and unfocused 2.5cm-diameter transducer. The results were as follows 1. Effective heating range$(42.5^{|circ}C\pm0.5^{\circ}C)$ were obtained 3cm in width and 4cm in depth from surface of phantom and temperature distribution was relatively uniform. 2. There was little heating effect more than 2cm away from transducer axis and more than 5cm in depth. 3. There was hot spots(more than $43^{\circ}C$) in $2.0\pm0.5cm$ depth from transducer along tranducer axis.

• Journal of Sericultural and Entomological Science
• /
• v.20 no.1
• /
• pp.5-10
• /
• 1978

The effects of foliar spray of Kinetin (6-Furfurylaminopurine) on the growth of mulberry tree and the metabolic activities in the leaves were measured. The results of this experimented are summarized as follows: 1. Foliar application of Kinetin was effective in increasing of leaf area, the fresh and dry weight of the leaves, the length and diameter of shoots. 2. Chlorophyll content was generally increased in all treated leaves. 3. All the treated leaves were higher in GOT activity than the control leaves but were lower in GPT activities. 4. The activities of the carbohydrate metabolism in the mulberry leaves were higher than that of the control in all treated leaves.

• Journal of the Korea Concrete Institute
• /
• v.12 no.4
• /
• pp.41-48
• /
• 2000

This study is to investigate for the frost resistance of high-strength concrete using finely ground granulated blast-furnace slag with experimental parameters, such as water/binder ratio, replacement proportion of granulated blast-furnace slag, air content and methods of curing. The high-strength concrete using granulated blast-furnace slag is effective to resist frost and decrease scaling. The more increasable replacement proportion of granulated blast-furnace slag is, the better the effect is. The high-strength concrete using granulated blast-furnace slag needs hydrating adequately to prevent deterioration by drying in the early curing period. The micro structure of high-strength concrete, increased to the pore number with diameter of 0.03~0.1mm, is changed by using granulated blast-furnace slag, but is presented differently according to water/binder ration and replacement proportion of granulated blast-furnace slag.

• Structural Engineering and Mechanics
• /
• v.51 no.3
• /
• pp.361-375
• /
• 2014

The main aim of this paper is to investigate the relationship between thickness and height of the axially symmetric cylindrical reinforced concrete (RC) walls by the help of a meta-heuristic optimization procedure. The material cost of the wall which includes concrete, reinforcement and formwork, was chosen as objective function of the optimization problem. The wall thickness, compressive strength of concrete and diameter of reinforcement bars were defined as design variables and tank volume, radius and height of the wall, loading condition and unit cost of material were defined as design constants. Numerical analyses of the wall were conducted by using superposition method (SPM) considering ACI 318-Building code requirements for structural concrete. The optimum wall thickness-height relationship was investigated under three main cases related with compressive strength of concrete and density of the stored liquid. According to the results, the proposed method is effective on finding the optimum design with minimum cost.