• KCI Concrete Journal
• /
• 제14권4호
• /
• pp.139-144
• /
• 2002

Concrete filled FRP tube has lately attracted attention as the member that can substitute the conventional reinforced concrete. Glass fiber and carbon fiber are some of available materials for FRP tube. Carbon tube is filament wound with specified winding angle to meet the appropriate capacity demands. Confinement effect of carbon tube is varied according to winding angle. In this study, a total 4 of large scale circular specimens of 30cm diameter and 60cm height is tested. To estimate the effect of winding angle and thickness of carbon tube on the increased confined compressive strength, the test tube are wound with $\pm45^{\circ}\;and\;\pm30^{\circ}$ with two types of thickness, 2mm and 3mm, respectively. It is shown that effectively increased confined strength and ductility are observed from the specimens with $\pm45^{\circ}$ winding angle than $\pm30^{\circ}$ winding angle. Increasing thickness is not as effective as adjusting winding angle for the confinement of concrete core.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.397-400
• /
• 2006

The addition of polypropylene fibers is effective to avoid spalling of shotcrete and concrete adopted tunnel and underground structure under the fire. In this study, a cement based mortar for fire resistance of polypropylene fiber was developed and evaluated by experimentally. The geometry and amount of polypropylene fibers which are diameter, length and fiber dosage were significant factors in aspect of the response values of fire resistance.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.87-88
• /
• 2009

본 연구에서는 ACI-01에 제시되지 않은 앵커볼트 직경($d_0$) 50mm($2^''$) 이상, 유효매입깊이($h_{ef}$) 635mm($25^''$) 이상의 대형콘크리트앵커의 전단성능 및 거동특성에 대한 24가지 실험을 수행하였다. 실험을 통하여 전단강도와 거동특성에 영향을 주는 요인을 분석하였다.

• Korean Chemical Engineering Research
• /
• 제52권3호
• /
• pp.294-301
• /
• 2014

This study focuses on analysis and comparison of entropy generation in various cross-sectional ducts along with fully developed laminar flow and constant uniform wall heat flux. The obtained results were compared in ducts with circular, semicircular, and rectangular with semicircular ends, equilateral triangular, and square and symmetrical hexagonal cross-sectional areas. These results were separately studied for aspect ratio of different rectangular shapes. Characteristics of fluid were considered at average temperature between outlet and inlet ducts. Results showed that factors such as Reynolds number, cross section, hydraulic diameter, heat flux and aspect ratio were effective on entropy generation, and these effects are more evident than heat flux and occur more in high heat fluxes. Considering the performed comparisons, it seems that semicircular and circular cross section generates less entropy than other cross sections.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 A
• /
• pp.232-235
• /
• 2000

Design and experiments of a nondestructive system to inspect deterioration of ACSR-OC (ACSR Outdoor Cross-linked Polyethylene Insulated Wire usually used in HV overhead distribution lines presented in this paper. ACSR-OC conductor built to pollutants air for a long period would be easily progress to corrode so that it may lead to the reduction of the effective cross section area of conductors. A fault diagnosis system consisting of a solenoid sensor, a constant current source with RF frequency signal processing unit and a motor driver/controller designed and implemented. This instrument can dot the sensor output variation due to deterioration corrosion, continuously. As a result, it was shown such corrosion detector can readily be utilized estimating the diameter change due to deterioration overhead distribution lines and in giving an warning or inform before severe aged conductor lead to fail.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.367-370
• /
• 2004

This paper present a new disk-type piezoelectric transformer. The input side of the transformer has a crescent-shaped electrode and the output side has a focused poling direction. The piezoelectric transformers operated in each transformer's resonance vibration mode. The electrodes and poling directions on commercially available piezoelectric ceramic disks were designed so that the planar or shear mode coupling factor $(k_p,\;k_{15})$ becomes effective rather than the transverse meed coupling factor $(k_{31})$. A single layer prototype transformer, 26[m] in diameter and 2.0[mm] thickness, was fabricated, such as step-up ratio, power transformation efficiency and temperature were measured.

• 한국환경과학회지
• /
• 제26권2호
• /
• pp.239-248
• /
• 2017

Green synthesis of gold nanoparticles(GNPs) considered more ecofriendly and cost effective than other chemical methods use of dangerous reagents and solvents, improved material and energy efficiency and enhanced design of non-toxic products. In this study, we developed a green synthesis method for using Caulis in Taeniam (BCT). BCT were characterized by UV-vis, Zetasizer, TEM, XRD, and FTIR. The antioxidant activity of BCT was determined by DPPH and ABTS radical-scavenging assays, and heme oxygenase-1 induction in RAW 264.7 macrophages. The resulting BCT appeared spherical with an average diameter of 67.171.39 nm The aAntioxidant activity was increased in a dependent manner. To conclude, the green synthesis of BCT-GNPs was successful, and it appers to be useful in the for future applications.

• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.39-47
• /
• 2011

Flow control range of valve, which is installed on pipeline, varies according to valve type, pipe diameter, pipe length, roughness, and elevation difference of both ends of pipeline. A lot of computation efforts and knowledge are needed to estimate flow control range of valve, considering above many parameters. The table of flow control range of each valve type is presented for convenience of pipeline design engineers who must make decision of valve size and type in this study. Also the reason that butterfly valve is recommended for flow control, and gate valve is forbidden is presented via quantification and figures in this study.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.468-472
• /
• 2003

MRE-1 dual thruster module(DTM) which will be installed to the present under development KOMPSAT(Korea Multi-Purpose Satellite) can provide reliable and cost-effective means of propulsive control for attitude and maneuvering control system. Thruster heat shield, one of the main components of DTM, is designed to intercept the radiative heat exchange between thruster and satellite during firing. The inside diameter of the current configuration will be decreased a little compared with that of the previous one due to manufacturing method change. Therefore, the possibility of interference between thruster and heat shield due to configuration change is investigated through structural analysis and their results are described in this paper.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1992-1997
• /
• 2003

This study is to develop the pretreatment for the excess and digested sludge by electro-coagulation and dewatering. Electrocoagulation is applied to excess and digested sludge before transferring to the piston type press for dewatering. Piston type filter press as a laboratory scale plant was used to estimate the dewaterability. MMD of excess sludge was increased from initial diameter of particles(34.16 ${\mu}m$) to the 87%(64.01 ${\mu}m$) after electrocoagulation. AI electrode is more effective than Fe electrode for the dewaterability of excess sludge. Electrodewatering after electrocoagulation as pretreatment makes the water content of sludge cake $50{\sim}60$ wt%.