• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.79-85
• /
• 2010

In this paper, we propose a web inspection system (WIS) for real-time detection of paper defects which can cause critical fractures during papermaking process. Our system incorporates high speed line-scan camera, lighting system, and detection algorithm to provide robust and precise detection of paper defects in real-time. Since edge defects are very crucial to the paper fractures, our system focuses on the edge region of the paper instead of inspecting the whole paper area. In our algorithm, image projection and sub-pixel operation are utilized to detect the edge defects precisely and connected component labeling and shape analysis techniques are adopted to extract various kinds of the region defects. Experimental results revealed that our web inspection system is very efficient for detecting paper defects during papermaking processes.

• 한국표면공학회지
• /
• 제31권5호
• /
• pp.237-244
• /
• 1998

In this stydy, submicron shallow trenches applied to STI(shallow tench isolation) were etched using inductively coupled $CI_2$/HBr and $CI_2/N_2$plasmas and the physical and electrical defects remaining on the etched silicon trench surfaces and the effects of various annealing and oxidation on the removal of the defects were studied. Using high resolution electron microscopy(HRTEM), Physical defects were investigated on the silicon trench surfaces etched in both 90%$CI_2$/ 10%$N_2$ and 50%$CI_2$/50%HBr. Among the areas in the tench such as trench bottom, bottom edge, and sidewall, the most dense defects were found near the trench bottom edge, and the least dense defects were found near the trench bottom edge, and least dense defects compared to that etched with ment as well as hydrogen permeation. Thermal oxidation of 200$\AA$ atthe temperature up to $1100^{\circ}C$apprars not to remove the defects formed on the etched silicon trenches for both of the etch conditions. To remove the physicall defects, an annealing treatment at the temperature high than $1000^{\circ}C$ in N for30minutes was required. Electrical defects measured using a capacitance-voltage technique showed the reduction of the defects with increasing annealing temperature, and the trends were similar to the results on the physical defects obtained using transmission electron microscopy.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.161-164
• /
• 1999

In order to investigate the effect of punching condition on the stretch flange formability of sheet for deep drawing hole expansion tests at various edge condition were done. Edge conditions were changed by altering tool clearances artifical defects grinding and deburring. For a determination of optimum edge condition of side panel of automobile punched section analysis and forming results were studied and the laboratory test results were used. In case of considered side panel tool clearance should be less than 15% and punched edge should be uniform without defects for safe forming

• Bulletin of the Korean Chemical Society
• /
• 제35권1호
• /
• pp.253-256
• /
• 2014

Functionalization of zigzag graphene nanoribbon (ZGNR) segment containing 120 C atoms with pyridine (3NV-ZGNR) defects was investigated on the basis of density-functional theory (DFT) calculations, results show that edge-modified ZGNRs by Sc can adsorb multiple hydrogen molecules in a quasi-molecular fashion, thereby can be a potential candidate for hydrogen storage. The stability of Sc functionalization is dictated by a strong binding energy, suggesting a reduction of clustering of metal atoms over the metal-decorated ZGNR.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.35-38
• /
• 2002

Real defects in composite structures were detected by using laser measuring system. Four types of specimens, that is, a composite laminate, a honeycomb structure, a free-edge delamination and an adhesive joint, were used to study the applicability of ESPI and Shearography to composite structures. Thermal loading method, which can easily induce the surface deformation of specimen, was used to detect defects. Experimental results show that defects in composite structures can be easily detected by ESPI and Shearography. Moreover, it shows that ESPI and Shearography can be usefully applied to the detection of defects in various kinds of composite structures.

• Applied Microscopy
• /
• 제50권
• /
• pp.27.1-27.6
• /
• 2020

Transition metal dichalcogenides (TMD), which is composed of a transition metal atom and chalcogen ion atoms, usually form vacancies based on the knock-on threshold of each atom. In particular, when electron beam is irradiated on a monolayer TMD such as MoS₂ and WS₂, S vacancies are formed preferentially, and they are aligned linearly to constitute line defects. And then, a hole is formed at the point where the successively formed line defects collide, and metal clusters are also formed at the edge of the hole. This study reports a process in which the line defects formed in a monolayer WS₂ sheet expends into holes. Here, the process in which the W cluster, which always occurs at the edge of the formed hole, goes through a uniform intermediate phase is explained based on the line defects and the formation behavior of the hole. Further investigation confirms the atomic structure of the intermediate phase using annular dark field scanning transition electron microscopy (ADF-STEM) and image simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권3호
• /
• pp.20-28
• /
• 2000

Air wiping technique is widely used because of easy and efficient coating control in present CGL The coating weight is controlled by nozzle header pressure. strip line speed, and the distance between strip and nozzle. Coating defects are resulted from the unbalance of these control factors and the inaccuracy of coating equipments. We investigates the main cause of coating defects, such as edge overcoating and coating deviation through various experiments. It is found that the edge overcoating is mainly come from nozzle lip type, and the coating deviation is caused by the unbalance of dynamic pressure.

• Journal of Information Display
• /
• 제12권3호
• /
• pp.121-124
• /
• 2011

The mechanism for lattice-shaped mura defects was proposed by characterizing the electro-optic properties of liquid crystal (LC), which showed different transmission properties between the normal and mura defect areas. An increase in the mura defect rate was observed when the dotted LC in the one drop filling (ODF) was exposed for a longer time. The dotted LC droplet at the edge evaporated more rapidly than that in the center. This resulted in a higher concentration of polar singles at the edge of the dotted LC droplet, leading to a higher ${\Delta}n$ value and higher transmittance. This implies that the reductio of the exposure time of the dotted LC to air plays a critical role in decreasing the occurrence of lattice-shaped mura defects in ODF.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2001년도 High Temperature Superconductivity Vol.XI
• /
• pp.40-40
• /
• 2001

• 정보저장시스템학회논문집
• /
• 제2권3호
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.