• The Journal of the Korean dental association
• /
• v.22 no.10 s.185
• /
• pp.869-877
• /
• 1984

An objective examination of 123 subjects aged from 19 to 23 was made from a clinical standpoints to determine the natural occurrence in anterior tooth contact in centric occlusion, and tooth contact in protrusive occlusion, left and right lateral excursions, and temporomandibular dysfunction. 1. In centric occlusion, maxillary 6 anterior contact type was frequently observe (30.08%) compared with other types of contact (incisor contact: 19.47%, no contact: 17.70%, canine and incisor contact: 15.04%, canines contact: 12.39%, unilateral canine contact: 5.31%) (P<0.01) 2. In protrusive position (edge to edge bite), maxillary central incisors contact was predominant (86.7%). (P<0.01) 3. In lateral excursion, there was not any significant difference between canine guided occlusion (47.79%) and group function occlusion (total 51.32%, AG:9.29%, PG:13.27%, G:28.76%). 4. Temporomandibular joint dysfunction was observed in 12.4% of 123 subjects.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.7
• /
• pp.559-564
• /
• 2016

The objectives of this paper are to develop a finite element analysis model to analyze press-fitted and bending load conditions in a press-fitted assembly, and propose a hub shape optimization method to minimize contact pressure near the shaft contact edge. Numerical asymmetric-axisymmetric finite element models have been developed to predict contact stress on press-fitted shafts. The global optimization method, genetic algorithm, local optimization method, and sequential quadratic programming were applied to a press-fitted assembly to optimize the hub contact edge geometry. The results showed that the maximum contact pressure with the optimized hub shape decreased more than 60 % compared to conventional hubs and the maximum contact stress affecting fatigue life was reduced about 47 %. Hub shape optimization can be useful to increase the load capability of press fits in terms of wear and fatigue behavior.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1559-1566
• /
• 1994

Using the finite element method, the contact force, contact band width and temperature distribution of lip seals analyzed for the interference including some nonlinearities such as material nonlinearity, geometrical nonlinearity and nonlinear contact boundary condition. The calculated results showed that the contact stress concentrated on the contact zone between the garter spring and the rubber toward the flex side, the contact edge of lip seals. The high contact forces due to the increased interference separate the sealing gap between the lip edge and the rotating shaft. This may lead to leak the sealed oil.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.198-203
• /
• 1997

This paper deals with a numerical study of the tribological contact stress distributions of elastomeric lip seah for oscillating shafts when the sealing interference and band width between the lip edge of contact seals the shaft are present. Using the finite element method, the contact stress and band width of scraper seals rare analyzed for the sealing interference including some nonlinearities such as geometrical nonlinearity, material nonlinearity and nonlinear contact boundary condition. The FEM results showed that the contact stress concentrated on the contacting lip zone between the contacting edge of lip and the shaft for the increased interference. In double lip scraper seals, the maximum contact stress of the dust lip, which is used to exclude foreign contaminants, is six times higher than that of the primary sealing lip, which is used to contain lubricants.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.54-62
• /
• 2008

In this paper the fretting wear of press-fitted specimens subjected to a cyclic bending load was simulated using finite element analysis and numerical method. The amount of microslip and contact variable at press-fitted and bending load condition in a press-fitted shaft was analysed by applying finite element method. With the finite element analysis result, a numerical approach was applied to predict fretting wear based on modified Archard's equation and updating the change of contact pressure caused by local wear with influence function method. The predicted wear profiles of press-fitted specimens at the contact edge were compared with the experimental results obtained by rotating bending fatigue tests. It is shown that the depth of fretting wear by repeated slip between shaft and boss reaches the maximum value at the contact edge. The initial surface profile is continuously changed by the wear at the contact edge, and then the corresponding contact variables are redistributed. The work establishes a basis for numerical simulation of fretting wear on press fits.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.7 s.250
• /
• pp.833-840
• /
• 2006

The paper presents a numerical solution to the problem of a hot rigid indenter sliding over a thermoelastic Winkler foundation with a thermal contact resistance at constant speed. It is shown analytically that no steady-state solution can exist for sufficiently high temperature or sufficiently small normal load or speed, regardless of the thermal contact resistance. However the steady state solution may exist in the same situation if the thermal contact resistance is considered. This means that the effect of the large values of temperature difference and small value of force or velocity which occur at no steady state can be lessened due to the thermal contact resistance. When there is no steady state, the predicted transient behavior involves regions of transient stationary contact interspersed with regions of separation regardless of the thermal contact resistance. Initially, the system typically exhibits a small number of relatively large contact and separation regions, but after the initial transient, the trailing edge of the contact area is only established and the leading edge loses contact, reducing the total extent of contact considerably. As time progresses, larger and larger numbers of small contact areas are established, unlit eventually the accuracy of the algorithm is limited by the discretization used.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.330-333
• /
• 2005

The paper presents a numerical solution to the problem of a hot rigid indenter siding over a thermoelastic Winkler foundation with a thermal contact resistance at constant speed. It is shown analytically that no steady-state solution can exist for sufficiently high temperature or sufficiently small normal load or speed regardless of the thermal contact resistance. However, the steady state solution may exist in the same situation if the thermal contact resistance is considered. This means that the effect of the large values of temperature difference and small value of force or velocity which occur at no steady state can be lessened due to the thermal contact resistance. When there is no steady-state the predicted transient behavior involves regions of transient stationary contact interspersed with regions of separation regardless of the thermal contact resistance. Initially, the system typically exhibits a small number of relatively large contact and separation regions, but after the initial transient the trailing edge of the contact area is only established and the leading edge loses contact, reducing the total extent of contact considerably. As time progresses, larger and larger number of small contact areas are established, until eventually the accuracy of the algorithm is limited by the discretization used.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.632-637
• /
• 2004

In the shrink or press fitted shaft such as railway axle, fretting can occur by cyclic stress and micro-slippage due to local movement between the shaft and the hub. When the fretting occurs in the press fitted shaft, the fatigue strength remarkably decreases compared with that of without fretting. In this paper, the analysis of contact stresses in a press fitted shaft in contact with a hub was conducted by finite element method and the micro-slip according to the bending load was analyzed. It is found that the largest stress concentration and maximum slip amplitude of shrink fitted shaft are found at the edge of the interface and the distribution of contact stresses at the contact edge has largely influenced and coefficient of friction.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.04a
• /
• pp.13-16
• /
• 2009

In order to investigate the effects of geometry factors such as a roil diameter ratio and backup roll crown of the stress concentration factor on the edge of backup roil end, 3-dimensional FEM analyses of stress at the contact of backup roll and work roll assembled in a 4-high strip mill were carried out, It was made clear that the peak stress at the edge is about 2 to 3 times of that at the longitudinal center of the roll barrel and the peak stress proportionally increase with decreasing the ratio of backup roll diameter to work roll diameter Furthermore a crowning on the backup roll is effective to decrease the maximum edge stress.