• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.217-221
• /
• 2001

Poly-Si/SiO$_2$/Si의 하부기판구조 위에 Co금속을 E-beam evaporation 방식으로 증착하고 급속 열처리 방식을 통해 inkjet 프린터헤드의 heater로 사용 할 수 있는 코발트실리사이드를 형성하였다. RTA로 열처리 온도와 시간을 변수로하여 코발트실리사이드의 가장 안정적 결정상 및 성분분포를 찾고 이렇게 제작된 박막의 면저항과 표면특성을 통해 고온에서 사용 할 수 있는지를 연구하였다. 박막을 발열체(400~$600^{\circ}C$)로 사용하기 위해서는 발열체가 외부배선과의 접촉 저항보다 커야하고 저항이 고온에서 크게 변하면 안 된다. 코발트 실리사이드는 80$0^{\circ}C$ 20sec에서 발열체로 사용하기에 적당한 특성을 보였다. 그러나 실리사이드반응이 RTA에서 40$0^{\circ}C$ 20sec에서 형성되기 시작하지만 열처리 온도를 높일수록 박막의 면저항과 상변화가 일어남으로 발열체로 사용 할 수 없고, 90$0^{\circ}C$ 20sec 이상에서는 표면의 거칠어짐으로 인해 면저항이 증가하는 현상을 보여 역시 발열체로 사용 할 수 없음을 알 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.12
• /
• pp.1063-1066
• /
• 2009

In this study, we fabricated pentacene organic thin film trasistors(OTFTs) which used aluminum oxide as the gate insulator. Aluminum oxide for OTFTs was deposited on glass substrate with a different deposition rate by E-beam evaporation. In case of the deposition rate of $0.1\;{\AA}$, the fabricated aluminum oxide gate insulating OTFT showed a threshold voltage of -1.36 V, an on/off current ratio of $1.9{\times}10^3$ and field effect mobility $0.023\;cm^2/V_s$.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2380-2382
• /
• 2005

UV-LIGA 공정을 이용하여 3차원 마이크로 인덕터 제작 기술에 관하여 연구하였다. 마이크로 인덕터의 코일, 비아(via), 코어(core)의 Multi-layer 제작을 위해 UV-LIGA 공정을 이용하였으며, 전해도금(electro plating)을 위한 씨올기(seed layer)로서는 e-beam evaporator를 이용하여 금속을 증착하였다. 3차원 마이크로 인덕터의 도금 방법으로는 전해도금을 사용하였으며, 코일과 비아 부분은 구리(Cu) 전해도금, 코어 부분은 니켈(Ni)과 철(Fe)의 합금인 퍼멀로이(Ni/Fe) 전해도금을 하였다. 3차원 마이크로 인덕터의 샘플크기로는 코어의 폭은 $300{\mu}m$, 전체 길이는 9.2mm, 두께는 $20{\mu}m$의 구조로 제작되었으며, 코일 부분은 폭이 $40{\mu}m$, 두께는 $30{\mu}m$이며, 코일턴 수는 70회의 구조로 제작하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.140-140
• /
• 2000

The initial growth mode of Nb on Ag(11) in sub-monolayer regime and the influence of subsequent 520K annealing are studied using UHV Scanning Tunneling Microscopy. E-beam evaporated Nb is deposited onto the substrate at RT, and STM measurements are carried out at RT and 78 K. With Nb being immiscible in bulk Ag, 3D islands formation begins at early stage and no particular ordered structure is found. After annealing to 520K, most of islands are disappeared from terrace. There exist 2 possibilities. : (1) Diffusion of Nb into the 2nd or 3rd layer of Ag substrate or (2) agglomeration of Nb on Ag at higher temperature. A model will be given to explain the evidence. In addition, we investigated the change of STM image according to bias voltage depending on island size. Possible physical mechanism responsible for such behavior together with interaction between Nb islands and reactive gases will be also discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.436-436
• /
• 2010

국내 반도체 시장은 세계 1위의 시장점유율을 가지고 있지만 핵심장비의 경우 국내 장비 기술의 낙후로 인해 대부분을 선진국에 의존하는 실정이다. 따라서 국내 장비 기술의 발전 요구에 따라 연구가 진행되었으며 기존 PE-CVD (Plasma Enhanced Chemical Vapor Deposition) 장비에서의 하전입자에 의한 기판 손상 가능을 제거하고 개개의 반응 원소의 에너지와 플럭스를 조절하여 다양한 공정온도에서 증착을 구현할 수 있는 HNB-CVD(Hyperthermal Neutral Beam Chemical Vapor Deposition) 장비를 개발하였다. 고밀도 플라즈마 생성을 위한 마이크로웨이브 SLAN(Slot Antenna) 소스를 사용하였으며 대면적 공정에 적합하도록 설계하였다. 최적의 설계와 진단을 위한 마이크로웨이브 SLAN 소스내의 E-field 분포 시뮬레이션과 Langmuir Probe 진단이 이루어졌다.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.

• Journal of the Korean Vacuum Society
• /
• v.9 no.2
• /
• pp.155-161
• /
• 2000

BN films composed of c-BN(70%) and h-BN(30%) phases have been synthesized by the ion beam assisted deposition (IBAD) process and stabilized by post-annealing. Boron was e-beam evaporated at 1.2 $\AA$/sec and nitrogen was ionized and accelerated at about 100 eV by the end-hall type ion gun. Substrates were negatively biased by DC 400 and 500 V, respectively, and heated at $700^{\circ}C$. Synthesized BN films were in-situ post-annealed at 700 or $800^{\circ}C$, respectively, for 1 hr without breaking vacuum. BN films without post-annealing were peeled off from substrates immediately when they were exposed to the air while those with post-annealing at $800^{\circ}C$ were stabilized. Post annealing reduced the film stress from 4.9 GPa to 3.4 GPa, but no considerable stress release in the c-BN phase was observed, contrary to previous reports that the stress relaxation in the c-BN phase is the main mechanism for the stabilization. Structural and chemical relaxation of non c-BN phase is supposed to be responsible for the film stress reduction and, in turn, stabilization, especially when the c-Bn content of the film is not high.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.163-167
• /
• 2002

Improved optical switching property of electrochromic nickel hydroxide/nickel glass thin film is reported. Nickel metal film was deposited on glass by e-beam evaporation before following electrochemical redox cycling to form nickel hydroxide for electrochromic activation. Without ITO (indium tin oxide) layer as electrical conductor, this electrode showed more rapid coloration rate than nickel hydroxide film on ITO substrate in the change of the electric voltage and optical transmittance. XPS analysis confirmed the existence of ultra-thin nickel metal layer (${\sim}10{\AA}$) between electrochemically grown nickel hydroxide and the glass substrate. It is concluded that the remained nickel metal nano-layer attribute to the conduction layer and the enhanced response time.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.2
• /
• pp.49-54
• /
• 2002

Cobalt silcides thin films were prepared on Poly-Si/$SiO_2$/Si substrates by Co metal depostion using E-beam evaporation method and rapid thermal annealing for the application of inkjet printing heater. The crystal phases and composition distributions of the films were investigated as functions of the rapid thermal annealing (RTA) temperatures (600~$900^{\circ}C$) and times (20~40 sec). The high temparature thermal stability was also investigated by the analysis of sheet resistance and crystalline properties. The stable $CoSi_2$ phases were obtained by the RTA annealing at $800^{\circ}C$ for 20 seconds showing $0.8 \Omega /\Box$ of sheet resitance. However, the sheet resistances were sharply increased at below $700^{\circ}C$ due to changes of crystalline phases. The temperature resistance coefficient of heating elements was found to be about $0.0014/^{\circ}C$, and the obtained cobalt silicided films can be applied to the printer heating elements.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.1-10
• /
• 2001

Chip-on-glass(COG) mounting of area array electronic packages was attempted by heating the rear surface of a contact pad film deposited on a glass substrate. The pads consisted of an adhesion (i.e. Cr or Ti) and a top coating layer(i.e. Ni or Cu) were healed by the UV laser beam transmitted through the glass substrate. The lather energy absorbed on the pad raised the temperature of a solder ball which is in physical contact with the pad, and formed a reflowed solder bump. The effects of the adhesion and top coating layer on the laser reflow soldering were studied by measuring temperature profile of the ball during the laser heating process. The results were discussed based on the measurement of reflectivity of the adhesion layer. In addition, the microstructures of solder bumps and their mechanical properties were examined.