• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.771-776
• /
• 2002

Optimal shape of the NFR suspension is studied and developed to improve the dynamic performance and reduce the vibration of the suspension system including a optical head slider. Since accurate position control and stability of the slider motion are highly required in NFR due to the narrower track width and the heavier slider than HDD slider with the low flying height, the dynamic characteristics of the suspension are very important to the mechanical performance of the system. The first natural frequencies in flexural and lateral motion of the suspension are critical factors affecting the dynamics and stability of the flying head, so that the dynamic parameters should be designed properly to avoid an excessive vibration or a crash of the slider on the disk. This paper optimizes the shape of the suspension based on homogenization method in NASTRAN and develops a new suspension shape for NFR system. The suspension is tested on experiment to verify the improvement of the dynamic characteristics.

• 대한기계학회논문집A
• /
• 제30권11호
• /
• pp.1479-1485
• /
• 2006

To minimize the leakage of microwave which can occur when one pulls the door of a microwave oven during its operation, shape optimization of the door frame is presented. A numerical optimization is implemented to minimize the dynamic twisting deformation of the door frame. Shape design variables are defined, which represent the dimension of the bead in the flange. Two optimal design problems are established to minimize the maximum twisting deformation from harmonic response analysis. The problems are solved, their results being compared and evaluated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.417-422
• /
• 2002

The main purpose of this paper is to determine the dynamic optimal shapes of tapered column with constant volume. The linear, parabolic and sinusoidal tapers with the regular polygon cross-section are considered, whose material volume and span length are always held constant. The ordinary differential equation including the effect of axial load is applied to calculate the natural frequencies. The Runge-Kutta method and Regula-Falsi methods are used to integrate the differential equation and compute the frequencies, respectively. Then the dynamic optimal shape whose lowest natural frequency is highest is determined by reading the critical value of the frequency versus section ratio curve plotted by the frequency data. In the numerical examples, the tapered columns are analysed and the numerical result of this study are shown in table and figures.

• 한국강구조학회 논문집
• /
• 제9권2호통권31호
• /
• pp.221-228
• /
• 1997

이 논문은 일정체적 단순지지 보-기둥의 동적 최적단면의 결정에 관한 연구이다. 정다각형 단면의 단면깊이가 포물선으로 변화하는 보-기둥에 대한 자유진동을 지배하는 상미분방정식을 유도하였다. 이 미분방정식에는 축하중효과를 고려하였고, Runge-Kutta method와 Regula-Falsi method를 이용하여 미분방정식을 수치적분하고 고유진동수를 산출하였다. 수치해석 결과로부터 얻어진 진동수-단면비 곡선의 임계값들을 분석하여 동적 최적단면을 결정하고 이 결과들을 표 및 그림에 나타내었다.

• Smart Structures and Systems
• /
• 제26권5호
• /
• pp.591-603
• /
• 2020

Dynamic deflection monitoring is an essential and critical part of structural health monitoring for high-speed railway bridges. Two critical problems need to be addressed when using inclinometer sensors for such applications. These include constructing a general representation model of inclination-deflection and addressing the ill-posed inverse problem to obtain the accurate dynamic deflection. This paper provides a dynamic deflection monitoring method with the placement of optimal inclinometer sensors for high-speed railway bridges. The deflection shapes are reconstructed using the inclination-deflection transformation model based on the differential relationship between the inclination and displacement mode shape matrix. The proposed optimal sensor configuration can be used to select inclination-deflection transformation models that meet the required accuracy and stability from all possible sensor locations. In this study, the condition number and information entropy are employed to measure the ill-condition of the selected mode shape matrix and evaluate the prediction performance of different sensor configurations. The particle swarm optimization algorithm, genetic algorithm, and artificial fish swarm algorithm are used to optimize the sensor position placement. Numerical simulation and experimental validation results of a 5-span high-speed railway bridge show that the reconstructed deflection shapes agree well with those of the real bridge.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.309-317
• /
• 2007

In this study, we conducted a vibration fatigue analysis of the lower control arm in a vehicle suspension system. The vehicle was driven during the tests so that the dynamic effects could be taken into account. The dynamic load of the frequency domain was superimposed on the frequency response analysis. We performed a virtual proving ground test using multi-body dynamics, along with a finite element analysis and fatigue life predictions. Shape optimization was also considered using the design of the experimental approach, and a response surface analysis was performed to improve the durability performance of the lower control arm. We identified the elements that had the most influence on the optimal shape of the finite element model and analyzed the sensitivity of those elements. Then the optimal points that minimized the amount of damage to the areas of interest were determined through a response surface analysis. The results suggested that the fatigue life of the model increased as its mass was not increased excessively, and demonstrated that these design procedures yielded an appropriate optimized lower control arm model.

• Advances in concrete construction
• /
• 제11권5호
• /
• pp.397-407
• /
• 2021

This paper investigates the optimal sensor placements and capabilities of this procedure for dynamic characteristics identification of arch dams. For this purpose, a prototype arch dam is constructed in laboratory conditions. Berke arch dam located on the Ceyhan River in city of Osmaniye is one of the highest arch dam constructed in Turkey is selected for field verification. The ambient vibration tests are conducted using initial candidate sensor locations at the beginning of the study. Enhanced Frequency Domain Decomposition and Stochastic Subspace Identification methods are used to extract experimental dynamic characteristics. Then, measurements are repeated according to optimal sensor locations of the dams. These locations are specified using the Effective Independence Method. To determine the optimal sensor locations, the target mode shape matrices which are obtained from ambient vibration tests of the selected dam with a large number of accelerometers are used. The dynamic characteristics obtained from each ambient vibrations tests are compared with each other. It is concluded that the dynamic characteristics obtained from initial measurements and those obtained from a limited number of sensors are compatible with each other. This situation indicates that optimal sensor placements determined by the Effective Independence Method are useful for dynamic characteristics identification of arch dams.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권4호
• /
• pp.476-490
• /
• 2016

This paper defines mode shape function of a composite solar panel assumed as Kirchhoff-Love plate for considering a torsional mode of composite solar panel. It then goes on to define dynamic model of a high-agility satellite considering the flexibility of composite solar panel as well as stiffness of a solar panel's hinge using Lagrange's theorem, Ritz method and the mode shape function. Furthermore, this paper verifies the validity of dynamic model by comparing numerical results from the finite element analysis. In addition, this paper performs a dynamic response analysis of a rigid satellite which includes only natural modes for solar panel's hinges and a flexible satellite which includes not only natural modes of solar panel's hinges, but also structural modes of composite solar panels. According to the results, we confirm that the torsional mode of solar panel should be considered for the structural design of high-agility satellite. Finally, we performed optimization of high-agility satellite for minimizing mass with solar panel's area limit using the defined dynamic model. Consequently, we observed that the defined dynamic model for a high-agility satellite and result of the optimal design are very useful not only because of their optimal structural design but also because of the dynamic analysis of the satellite.

• 대한전자공학회논문지SP
• /
• 제41권3호
• /
• pp.121-127
• /
• 2004

This paper presents a new vertex selection scheme for shape approximation. In the proposed method, final vertex points are determined by "two-step procedure". In the first step, initial vertices are simply selected on the contour, which constitute a subset of the original contour, using conventional methods such as an iterated refinement method (IRM) or a progressive vertex selection (PVS) method In the second step, a vertex adjustment Process is incorporated to generate final vertices which are no more confined to the contour and optimal in the view of the given distortion measure. For the optimality of the final vertices, the dynamic programming (DP)-based solution for the adjustment of vertices is proposed. There are two main contributions of this work First, we show that DP can be successfully applied to vertex adjustment. Second, by using DP, the global optimality in the vertex selection can be achieved without iterative processes. Experimental results are presented to show the superiority of our method over the traditional methods.

• 한국강구조학회 논문집
• /
• 제19권1호
• /
• pp.99-106
• /
• 2007

이 논문은 일정체적 양단고정 기둥의 정 동적 최적형상에 관한 연구이다. 기둥의 단면은 정다각형이며, 단면깊이는 포물선으로 변화하는 변단면이다. 축방향 압축하중이 작용하는 기둥의 고유진동수 및 좌굴하중을 산정하는 수치해석 기법을 개발하였다. 그러한 기둥의 자유진동을 지배하는 미분방정식을 유도하고 Runge-Kutta법과 Regula-Falsi법을 이용하여 고유진동수를 산정하였다. 수치해석의 결과로부터 얻어진 하중-고유진동수 사이의 관계를 이용하여 기둥의 좌굴하중을 산정하였다. 기둥의 변수연구를 통하여 동적 안정영역, 동적 최적형상 및 최강기둥의 형상을 산출하였다.