• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.219-222
• /
• 2004

This research is about SDM (Structural Dynamics Modification) technique using embosses. SDM using embosses do not need to add additional mass element ana model of embosses and resulting huge calculation for getting analytical solution of an embossed structure. The object of this research is to suggest a method to guide placing embossment in a structure to raise its natural frequencies. Two methods to optimize model with embossing are suggested, indepuldently. The former is response surface analysis by neural network. And the latter is an indirect method using modal dynamic strain energy.

• International Journal of High-Rise Buildings
• /
• v.10 no.3
• /
• pp.229-242
• /
• 2021

Dynamic characteristics of tall building structures with double negative stiffness damped outriggers (2NSDO) are parametrically studied using the theoretical formula. Compared with one negative stiffness damped outrigger (1NSDO), 2NSDO can achieve a similar maximal modal damping ratio with a smaller negative stiffness ratio. Besides, the 2NSDO can improve the maximum achievable damping ratio to about 30% with less consumption of an outrigger damping coefficient compared with the double conventional damped outriggers (2CDO). Besides, the responses of structures with 2NSDO under fluctuating wind load are investigated by time-history analysis. Numerical results show that the 2NSDO is effective in reducing structural acceleration under fluctuating wind load, being more efficient than 1NSDO.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.7 s.262
• /
• pp.777-783
• /
• 2007

Since the performance of the circuit breaker mainly depends on the spring operating mechanism, the analysis of the spring operating mechanism is required. The spring, especially closing spring, stores the deformation energy due to the compression and then accelerates the big loads rapidly in the circuit breaker. To accurately carry out the kinematic and dynamic analysis of the circuit breaker, the precise modeling of the spring behavior is necessary. In this paper, the static stiffness of the spring is captured by using the tester. A simple mechanism similar to the spring operating mechanism was designed to generate the release motion of the spring. A high speed camera was used to capture the behavior of the spring. Three types of spring models such as a linear spring model, modal spring model, and nodal spring model are suggested and compared with the experimental results.

• Smart Structures and Systems
• /
• v.24 no.4
• /
• pp.525-539
• /
• 2019

In this study, vibration characteristics of a gravity-based caisson-foundation breakwater system are investigated for ambient and geometric parameters such as various waves, sea levels, and foundation conditions. To achieve the objective, following approaches are implemented. Firstly, operational modal analysis methods are selected to identify vibration modes from output-only dynamic responses. Secondly, a finite element model of an existing caisson-foundation breakwater system is established by using a structural analysis program, ANSYS. Thirdly, forced vibration analyses are performed on the caisson-foundation system for two types of external forces such as controlled impacts and wave-induced dynamic pressures. For the ideal impact, the wave force is converted to a triangular impulse function. For the wave flow, the wave pressure acting on the system is obtained from wave field analysis. Fourthly, vibration modes of the caisson-foundation system are identified from the forced vibration responses by combined use of the operational modal analysis methods. Finally, vibration characteristics of the caisson-foundation system are investigated under various waves, sea levels, and foundations. Relative effects of foundation conditions on vibration characteristics are distinguished from that induced by waves and sea levels.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.7
• /
• pp.203-208
• /
• 2000

The vibration of a mask degrades the color purity in CRT Therefore, a damping wire is put into contact with the mask to reduce the vibration in perfectly flat CRT. In this study, we analyzed the vibration of the mask contacting with the damping wire using FEM. First we calculated the natural frequencies and mode shapes of the mask by modal analysis, and compared them with the measured results to confirm our finite element model. The modal analysis of the wire was also performed to investigate resonance with the mask. Finally, the transient dynamic analysis of the mask contacting with the wire was performed. The vibration of the mask was measured to confirm our analysis, and the results are in good agreement with the analysis.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.221-222
• /
• 2000

The vibration of a mask degrades the color purity in CRT. In order to reduce the vibration. a damping wire is put into contact with the mask in the Flatron. We analyzed the vibration of the mask considering the damping wire using FEM. The natural frequencies and mode shapes of the mask are calculated by modal analysis. And those are compared with the measured results to confirm our finite element model. The modal analysis of the wire is also performed to investigate resonance with the mask. Finally, the transient dynamic analysis of the mask contacting with the wire is performed. The vibration of the mask is measured to confirm our analysis, and the results are in good agreement with the analysis.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.1 s.23
• /
• pp.55-62
• /
• 2007

The Paper presents three methods for calculating the natural frequencies of cantilevered curved Beams. A summary is given of the development of two techniques: theoretic value and the result of the experiment. Theoretic value of curved beam vibration analysis are derived from complementary variational principles assuming as unknown stress-displacement result fields. In order to perform free vibration analysis of curved beam, Aluminum-made cantilevered curved beam is used in experiment. Experimental input and output signals are derived from the impact hammer and the one accelemeter are amplificated by an amplifier. The validity of the modal analysis method

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3353-3360
• /
• 2022

Using data from the design earthquake of the Korean standard nuclear power plant, seismic analyses of a fuel assembly are conducted in this study. The modal characteristics are used to develop an input deck for the seismic analysis. With a time history analysis, the responses of the fuel assembly in the event of an earthquake are obtained. In particular, the displacement, velocity, and acceleration responses at the center location of the fuel assembly are obtained in the time domain, with these outcomes then used for a detailed structural analysis of the fuel rods in the ensuing analyses. The response spectra are also generated to determine the response characteristics in the frequency domain. The structural integrity of the fuel assembly can be ensured through this type of time history analysis considering the input excitations of various earthquakes considered in the design.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.225-231
• /
• 2012

Drop simulations of the board level in the flip chips with solder joints have been highlighted for years, recently. Also, through the study on the life prediction of thermal fatigue in the flip chips considering underfill, its importance has been issued greatly. In this paper, dynamic analysis using the implicit method in the Finite Element Analysis (FEA) is carried out to assess the factors effecting on flip chips considering underfill. The design parameters are size and thickness of chip, and size, pitch and array of solder ball with composition of Sn1.0Ag0.5Cu. The board systems by JEDEC standard is modeled with various design parameter combinations, and through these simulations, maximum yield stress and strain at each chip are shown at the solder balls. Modal analysis is simulated to find out the relation between drop impact and vibration of the board system.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.4
• /
• pp.303-314
• /
• 2009

The present paper shows the results of numerical and experimental modal analyses of Francis runners, which were executed in air and in still water. In its first part this paper is focused on the numerical prediction of the model parameters by means of FEM and the validation of the FEM method. Influences of different geometries on modal parameters and frequency reduction ratio (FRR), which is the ratio of the natural frequencies in water and the corresponding natural frequencies in air, are investigated for two different runners, one prototype and one model runner. The results of the analyses indicate very good agreement between experiment and simulation. Particularly the frequency reduction ratios derived from simulation are found to agree very well with the values derived from experiment. In order to identify sensitivity of the structural properties several parameters such as material properties, different model scale and different hub geometries are numerically investigated. In its second part, a harmonic response analysis is shown for a Francis runner by applying the time dependent pressure distribution resulting from an unsteady CFD simulation to the mechanical structure. Thus, the data gained by modern CFD simulation are being fully utilized for the structural design based on life time analysis. With this new approach a more precise prediction of turbine loading and its effect on turbine life cycle is possible allowing better turbine designs to be developed.