• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.824-827
• /
• 2000

Fabrication of InP-based photonic devices by dry etch Process is important for clear formation of waveguide mesa structure. We have developed more efficient etch process of the inductively coupled plasma (ICP) with low damages and less polymeric deposits for the InP-based photonic devices than the reactive ion etching (RIE) technique. We report the tendency of etch rate variation by the process parameters of the RF power, pressure, gas flow rate, and the gas mixing ratio. The surface roughness of InP-based waveguide structure was more improved by the light wet etching in the mixed solution of H$_2$SO$_4$:H$_2$O (1:1)

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.1
• /
• pp.6-9
• /
• 2012

In this study, we carried out an investigation of the etching characteristics (etch rate, selectivity to $SiO_2$) of ZnO thin films in $N_2/Cl_2$/Ar inductivity coupled plasma. A maximum etch rate and selectivity of 108.8 nm/min and, 3.21, respectively, was obtained for ZnO thin film at a $N_2/Cl_2$/Ar gas mixing ratio of 15:16:4 sccm. The plasmas were characterized by optical emission spectroscopy. The x-ray photoelectron spectroscopy analysis showed the efficient destruction of oxide bonds by ion bombardment. An accumulation of low volatile reaction products on the etched surface was also shown. Based on this data, an ion-assisted chemical reaction is proposed as the main etch mechanism for plasmas containing $Cl_2$.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.490-495
• /
• 1999

In 0.18 $\mu \textrm m$ LOGIC device, the etch rate of NMOS polysilicons is different from that of PMOS polysilicons due to the state of polysilicon to manufacture gate line. To control the etch profile, we tested the ratio of $Cl_2$/HBr gas and the total chamber pressure, and also we reduced Back He pressure to get the vertical profile. In the case of manufacturing the gate photoresist line, we used Bottom Anti-Reflective Coating (BARC) to protect refrection of light. As a result we found that $CF_4O_2$ gas is good to etch BARC, because of high selectivity and good photoresist line profile after etching BARC. in the results of the characterization of plasma damage to the antenna effect of gate oxide, NO type thin film(growing gate oxide in 0, ambient followed by an NO anneal) is better than wet type thin film(growing gate oxide in $0_2+H_2$ ambient).

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.483-488
• /
• 2006

Etching process of PMMA (Polymethyl Methacrylate) on glass surface was investigated by dry etching technique using remote plasma. To determine the etching characteristics, the remote plasma etching was conducted for various process parameters such as plasma power, reaction gas and distance from plasma generation. As the distance from the plasma generation was increased, the etch rate of PMMA was linearly decreased by radical density in plasma. PMMA has removed by reactive radicals in the plasma. The etch rate increased with plasma power because of more reactive radicals. The etch rate and surface roughness of PMMA increased with $O_2$ concentration in the etchant.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.202-205
• /
• 2010

In this study, the etch properties of $Al_2O_3$ thin films deposited by atomic layer deposition were investigated as a function of the $O_2$ content in $BCl_3$/Ar inductively coupled plasma. The experiments were performed by comparing the etch rates and selectivity of $Al_2O_3$ over the hard mask materials as functions of the input plasma parameters, such as the gas mixing ratio, DC-bias voltage, ratio-frequency (RF) power and process pressure. The highest obtained etch rate was 477 nm/min at an RF power of 700 W, $O_2$ to $BCl_3$/Ar gas ratio of 15%, DC-bias voltage of -100 V and process pressure of 15 mTorr. The deposition occurred on the surfaces when the amount of $O_2$ added to the $BCl_3$/Ar gas was too high at a low DC-bias voltage or high process pressure. X-ray photoelectron spectroscopy was used to investigate the chemical reactions on the etched surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.382-382
• /
• 2010

The etch characteristics of the $HfAlO_3$ thin films and selectivity of $HfAlO_3$ to $SiO_2$ in $Cl_2/BCl_3$/Ar plasma were investigated in this work. The maximum etch rate was 108.7 nm/min and selectivity of $HfAlO_3$ to $SiO_2$ was 1.11 at $Cl_2$(3sccm)/$BCl_3$(4sccm)/Ar(16sccm), RF power of 500 W, DC-bias voltage of - 100 V, process pressure of 1 Pa and substrate temperature of $40^{\circ}C$. As increasing RF power and DC-bias voltage, etch rates of the $HfAlO_3$ thin films increased. Whereas as decreasing of the process pressure, those of the $HfAlO_3$ thin films were increased. The chemical reaction on the surface of the etched the $HfAlO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS).

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.106-109
• /
• 2011

We investigated the etching characteristics of titanium nitride (TiN) thin film in $BCl_3$/Ar inductively coupled plasma. The etching parameters were the gas mixing ratio, radio frequency (RF) power, direct current (DC)-bias voltages and process pressures. The standard conditions were as follows: total flow rate = 20 sccm, RF power = 500 W, DC-bias voltage = -100 V, substrate temperature = $40^{\circ}C$, and process pressure = 15 mTorr. The maximum etch rate of TiN thin film and the selectivity of TiN to $Al_2O_3$ thin film were 54 nm/min and 0.79. The results of X-ray photoelectron spectroscopy showed no accumulation of etch byproducts from the etched surface of TiN thin film. The TiN film etch was dominated by the chemical etching with assistance by Ar sputtering in reactive ion etching mechanism, based on the experimental results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.747-750
• /
• 2007

This study proposes that chlorine residue after metal etch as the source of metal corrosion, and charges should be removed by optimizing etch, PR strip and cleaning condition. Charges distributed along the metal line acts as a source of tungsten (W) plug corrosion when associated with following cleaning solution. In cleaning process after metal etch and PR strip, chemical selection is significantly important in terms of metal corrosion. Optimal corrosion preventive PH, no metal attack (choice of optimal inhibitants), high by product removal efficiency and optimal de ionized water treatment condition is critical to the metal corrosion prevention.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.718-722
• /
• 2011

In this work, we investigated to the etching characteristics of the TiN thin film in He/$BCl_3/Cl_2$ plasma. The etch rate was measured by the gas mixing ratio, the RF power, the DC bias voltage and the process pressure. The maximum etch rate in He/$BCl_3/Cl_2$ plasma was 59 nm/min. The etch rate increased as the RF power and the DC-bias voltage was increased. The chemical reaction on the surface of the etched the TiN thin films was investigated with X-ray photoelectron spectroscopy (XPS). The intensity of Ti 2p and N 1s peaks are varied during etching process. A new peak was appeared in He/$BCl_3/Cl_2$ plasma. The new peak was revealed Ti-$Cl_x$ by Cl 2p peak of XPS wild scan spectra analysis.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.55-60
• /
• 2017

The supercritical $CO_2$ (sc-$CO_2$) mixture and the sc-$CO_2$-based Photoresist(PR) stripping(SCPS) process were applied to the removal of the post etch/ash PR residue on aluminum patterned wafers and the results were observed by scanning of electron microscope(SEM). In the case of MDII wafers, the carbonized PR was able to be effectively removed without pre-stripping by oxygen plasma ashing by using sc-$CO_2$ mixture containing the optimum formulated additives at the proper pressure and temperature, and the same result was also able to be obtained in the case of HDII wafer. It was found that the efficiency of SCPS of ion implanted wafer improved as the temperature of SCPS was high, so a very large amount of MEA in the sc-$CO_2$ mixture could be reduced if the temperature could be increased at condition that a process permits, and the ion implanted photoresist(IIP) on the wafer was able to be removed completely without pre-treatment of plasma ashing by using the only 1 step SCPS process. By using SCPS process, PR polymers formed on sidewalls of metal conductive layers such as aluminum films, titanium and titanium nitride films by dry etching and ashing processes were removed effectively with the minimization of the corrosion of the metal conductive layers.