• Journal of the Korean Applied Science and Technology
• /
• v.27 no.3
• /
• pp.318-324
• /
• 2010

In this study, commercial pellet type sorbents for the collection of $CO_2$ from a local municipal waste incinerator were prepared and characterized in terms of adsorption efficiency by varying the operating conditions of a field process. The concentration of $CO_2$ in the flue gas ranged from 8 to 10%, which entered the test packed bed. As a result of this experiment, the sorbent procured from A-company, which is mainly composed of calcium compounds, showed the highest adsorption efficiency. The regeneration efficiency was fairly low, however. It also was found that based on adsorption breakthrough time, the relatively low flow rate of 10 LPM into the bed allowed higher collection efficiency. The higher flow rate of 40 LPM, on the other hand, tended to decrease the retention of the adsorption.

• Clean Technology
• /
• v.19 no.2
• /
• pp.165-172
• /
• 2013

In this study, the hydrogen chloride removal using K-based dry sorbents ($K_2CO_3/Al_2O_3$, KEPRI, Korea) was studied with varying the pressure in a fixed bed reactor (15 cm tall bed with 0.5 cm I.d.). Working temperature was $400^{\circ}C$ and feed gas concentration was 750 ppm (HCl vol%, $N_2$ balance). The chloride sorption capacity of sorbent increases with increasing pressure (1, 5, 10, 15 and 20 bar). Also, after forming KCl crystal by reaction with $K_2CO_3$ and HCl, owing to the strong bonding energy, sorbent regeneration was practically impossible. Its optical, physical and chemical characterizations were evaluated by SEM, EDAX, BET, TGA and XRD. At $400^{\circ}C$ and 20 bar condition, working condition for the dehalogenation process after gasification, K-based dry sorbent showed high HCl sorption capacity and HCl/$N_2$ separation performances comparing with Ca-based and Mg-based dry sorbents.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.4
• /
• pp.5-14
• /
• 2016

Numerical simulation of dynamic soil-pile-structure interaction embedded in a dry sand was carried out. 3D model of the dynamic centrifuge model tests was formulated in a time domain to consider nonlinear behavior of soil using the finite difference method program, FLAC3D. As a modeling methodology, Mohr-Coulomb criteria was adopted as soil constitutive model. Soil nonlinearity was considered by adopting the hysteretic damping model, and an interface model which can simulate separation and slip between soil and pile was adopted. Simplified continuum modeling (Kim et al., 2012) was used as boundary condition to reduce analysis time. Calibration process for numerical modeling results and test results was performed through the parametric study. Verification process was then performed by comparing numerical modeling results with another test results. Based on the calibration and validation procedure, it is identified that proposed modeling method can properly simulate dynamic behavior of soil-pile system in dry condition.

• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.60-67
• /
• 2021

This study presented techno-economic analysis of a 500 MWe oxy-coal power plant with CO2 capture. The power plant included a circulating fluidized-bed (CFB), ultra-supercritical steam turbine, flue gas conditioning (FGC), air separation unit (ASU), and CO2 processing unit (CPU). The dry flue gas recirculation (FGR) was used to control the combustion temperature of CFB. One FGR heat exchanger, one heat exchanger for N2 stream exiting ASU, and a heat recovery from CPU compressor were considered to enhance heat efficiency. The decrease in the temperature difference (ΔT) of the FGR heat exchanger that means the increase in heat recovery from flue gas enhanced the electricity and exergy efficiencies. The annual cost including the FGR heat exchanger and FGC cooling water was minimized at ΔT = 10 ℃, where the electricity efficiency, total capital cost, total production cost, and return on investment were 39%, 1371 M$, 90 M$, and 7%/y, respectively.

• Journal of Venture Innovation
• /
• v.5 no.2
• /
• pp.85-99
• /
• 2022

Dryers becoming commercially available for experimental and industrial use are classified to general drying oven, hot-air dryer, vacuum dryer, freezing dryer, etc. and kinds of them are various from the function, size and volume, etc. But the moisture measurement is not applied although it is important factor for the quality control and the performance improvement of products, and then now is very passive because the weight is weighed arbitrarily after dry-end. Generally the method for measuring moisture is divided by a direct measurement method and a indirect measurement method, and the former such as the change of weight or volume on the front and rear of separation of moisture, etc. is mainly used. Relatively a indirect measurement is very limited to apply due to utilize measurement apparatuses using temperature conductivity and micro-wave etc. In this research, we easily designed the moisture measurement system using the open-source based Arduino, and monitored moisture fluctuations and weight profiles in the real-time without the effect of external environment. Concretely the temperature-humidity and load cell sensors were packaged into a drying oven and the various change values were measured, and their sensors capable to operate 60℃ and 80℃ were selected to suitable for the moisture sensitive materials and the food dry. And also the performance safety using the organic samples of banana, pear, sawdust could be secured because the changes of evaporation rate as the dry time and temperature, and the measurement values of load cell appeared stable response characteristics through repeated experiments. Hereafter we judge that the reliability can be improved increasingly through the expansion of temperature-humidity range and the comparative analysis with CFD(Computational Fluid Dynamics) program.

• Microbiology and Biotechnology Letters
• /
• v.37 no.3
• /
• pp.231-237
• /
• 2009

This paper aimed to develop a solvent extraction and purification process to recover high-purified ${\beta}$-carotene from recombinant Escherichia coli. Cells harvested from the culture broth were treated through numerous steps: dehydration, solvent extraction, crystal formation and separation. To optimize the extracting condition, experiments were carried out to investigate the effect of cell disruption, temperature, organic solvents, solvent-biomass ratio on the yield of ${\beta}$-carotene extracted from cells. The result indicated that no significant differences of extraction yield were observed from cells with or without step of cell disruption. Among different extracting solvents, the highest extraction yield of ${\beta}$-carotene, 30.3 mg-${\beta}$-carotene/g-dry cells, was obtained with isobutyl acetate at solvent-biomass ratio 25 mL/g-dry cells at $50^{\circ}C$. Notably, in case of acetone, the extraction yield was quite low when using acetone itself, but increased almost up to the highest value when combining this solvent and olive oil. The purity of ${\beta}$-carotene crystals obtained from crystallization and separation was 89%. The purity degree was further improved up to 98.5% by treating crude crystals with additional ethanol washing.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.1
• /
• pp.1-20
• /
• 1983

It has been known that the insect molting hormone and its analogues exist also in plant kingdom and their concentration has been found to be about 0.1~2.0% of dry matter, which is equivalent to $10^3{\sim}10^5$ times of those in insects. This study was carried out; 1) to isolate the phytoecdysones from Korean Achyranthes radix and characterize their physico-chemical properties. 2) to investigate the biological activity of this phytoecdysone on Bombyx mori larvae. The resuls were summarized as follows; 1. The extraction method of phytoecdysones was optimized by three consecutive reflux for 1hr using 200g of dried and milled radix per 1l methanol. 2. The purification from the crude extract was made by a series of steps such as precipitation of gum-type polymer with n-Butyl acetate, adsorption on technical grade silica and chromatography with neutral alumina. The conditions of each step were optimized and the resulting crude crystal was about 500mg per kg dry radix. 3. The crude crystal from the cultivated Achyranthes(Achyranthes japonia) contained ecdysterone (20-hydroxyecdysone) and inokosterone in the proportion of one to one. In order to separate these, a series of processes such as acetylation, separation by alumina column chromatography deacetylation by alcoholysis, deionization and crystallization were introduced and optimized 125mg of ecdysterone and 18mg of inokosterone per kg dry radix were thus obtained. 4. The wild Achyranthes (Achyranthes obtusifolia) radix was found to contain the ecdysterone only. A 285mg of ecdysterone was crystallized per kg dry radix. 5. Isolated ecdysterone, inodosterone and acetylated compounds were characterized by IR., UV., NMR spectroscopy, mp, TLC and densitometry. 6. Ligation experiment was undertaken to confirm the biological activity of the purified ecdysterone; the ecdysterone could induce larval-pupal metamorphosis in the ligated abdomen of 4th instar larvae injecting 0.5~1.0${\mu}g$. 7. By ecdysterone feeding experiment using artificial diet, it was elucidated that the critical time of feeding would be the first half of each instar resulting in increased weight of silk layer. 8. The ecdysterone was fed to 5th instar silkworm at the level of 1, 2, 3, 5ppm of dry feed of artificial diet containing 5% mulberry leaves for 72hrs. At 2ppm of the concentration. body weight and silk layer weight were arrived at maximum. But at higher concentrations body weight and silk layer weight decreased than the control group. At 2ppm of the concentration, body weight was increased by 12.5%. 9. Feeding 2ppm of ecdysterone at the later half of 5th instar, the duration of larvae was shortened.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.660-667
• /
• 2010

In this research polyimide, Matrimid 5218, hollow fiber membrane was used to recover sulfur hexafluoride($SF_6$) which is one of the six greenhouse gases from $N_2/SF_6$ mixture gas. Fibers were spun from using dry-wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a sponge-like substructure. The developed module had a permeance of 0.78-1.36 GPU for $N_2$ with $N_2/SF_6$ selectivity of 2.44-5.08 at various pressure and temperature. For recovery of $SF_6$, a membrane module and 10 vol.% $SF_6$ from $N_2/SF_6$ mixture gas was used. The effects of various operating condition such as pressure, temperature, and retentate side flow rate were tested. When pressure and temperature were increased and retentate flow rate was decreased, the $SF_6$ purity in recovered gas was increased up to 37.5 vol.% with decreasing recovery ratio. When retentate flow rate was increased pressure and temperature was decreased, the $SF_6$ recovery ratio in retentate side was increased up to 89% with decreasing the $SF_6$ purity in retentate side.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.12-21
• /
• 2014

Nickel oxide ores are composed of two kinds of minerals; one is saprolite that is processed by smelting to obtain nickel products, and the other is limonite that is used in hydrometallugical processes. It is not efficient economically to process the mixture of limonite and saprolite, so the processes to saparate the ore mixture should be developed. In the present study, the mixture was separated by dry-classification after liberationg using grindability difference between limonite and saprolite. Consequently, it is possible to obtain the limonite with less than 10% of Mg+Si contents, which could be treated by hydrometallurgical processes, when the limonite contain less than 30% of saprolite.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.224-233
• /
• 2012

To improve permeation performance of gas separation membrane, polysulfone hollow fiber membrane was prepared by wet-dry phase inversion method using Triton X-100 as non-ionic additive. And variation of gas permeation behavior by additive was investigated. Various spinning conditions such as air gap, concentration of polymer, dope tank temperature were controlled and these effects were studied. The morphology and gas permeation property of hollow fiber membranes were investigated using scanning electron microscope (SEM) and bubble flow meter respectively. We confirmed that the membranes added with Triton X-100 had a smooth external skin at various air gap length conditions. The macrovoids of these hollow fiber membranes were more developed with increase of air-gap from 4 to 90 cm and that induced higher permeance. The permeance of polysulfone membranes has the higher value at comparatively lower concentration polymer (30 wt% polysulfone) and lower concentration of additive (15 wt% Triton X-100). When temperature in dope tank was controlled, the membranes prepared at $100^{\circ}C$ showed low permeance because of volatilization of additive and solvent.