• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.473-480
• /
• 2011

The proton exchange membrane (PEM) fuel cell system is critically dependent on the humidity, which should be properly maintained over the entire operating range. A membrane humidifier is used for the water management in the PEMFC because of the membrane humidifier's reliable performance and zero parasitic power loss. In the PEMFC system, the membrane humidifier is required to provide appropriate humidity for the design point of the fuel cell. Although the performance of the fuel cell depends on the performance of the humidifier, few studies have provided a systematic analysis of the humidifier. We carry out an experimental analysis of the membrane humidifier using a vapor condensation bottle. The dry air pressure, water flow temperature, and air flow rate were chosen as the operating parameters. The results show that the time constant for the dynamic response of the membrane humidifier is relatively short, but additional analysis should be carried out.

• Microbiology and Biotechnology Letters
• /
• v.37 no.3
• /
• pp.197-203
• /
• 2009

An indole oxygenase originated from Rhodococcus sp. RHA1 was cloned into the expression vector, pTrc99A, in Escherichia coli, and designated pTCAN1. The pTCAN2 was constructed from pTCAN1 by the deletion of $lacI^q$ for the constitutive expression of indole oxygenase without adding IPTG in the medium. The complete open reading frame of indole oxygenase was 1,224 bp long, which encodes a protein of 407amino acids. Crude extracts of E. coli $DH5{\alpha}$/pTCAN1 and pTCAN2, respectively, were prepared and subjected to SDS-PAGE analysis. A band corresponding to molecular mass of about 43 kDa was appeared and this result correlated with the predicted molecular mass of cloned indole oxygenase. The E. coli harboring pTCAN1 and pTCAN2, respectively, showed blue color colony in LB plate. The pigment showing blue color was prepared from E. coli $DH5{\alpha}$/pTCAN2, and identified as indigo by experiments using spectrophotometer, HPLC, and TLC. The indigo-forming activity of indole oxygenases from the whole cell of E. coli $DH5{\alpha}/pTCAN1$ cultured at LB medium added 1mM of IPTG and that of E. coli/pTCAN2 showed about 1.75nmol/min/mg DCW (dry cell weight) and 3.85 nmol/min/mg DCW, respectively. Also, the E. coli $DH5{\alpha}$/pTCAN2 produced about $236{\mu}M$ of indigo after 48 hours incubation in TB medium supplemented with 2.5 mM of tryptophan.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.99-105
• /
• 2015

PURPOSES: In this study, alkali-activated blast-furnace slag (AABFS) was investigated to determine its capacity to absorb carbon dioxide and to demonstrate the feasibility of its use as an alternative to ordinary Portland cement (OPC). In addition, this study was performed to evaluate the influence of the alkali-activator concentration on the absorption capacity and physicochemical characteristics. METHODS: To determine the characteristics of the AABFS as a function of the activator concentration, blast-furnace slag was activated by using calcium hydroxide at mass ratios ranging from 6 to 24%. The AABFS pastes were used to evaluate the carbon dioxide absorption capacity and rate, while the OPC paste was tested under the same conditions for comparison. The changes in the surface morphology and chemical composition before and after the carbon dioxide absorption were analyzed by using SEM and XRF. RESULTS: At an activator concentration of 24%, the AABFS absorbed approximately 42g of carbon dioxide per mass of paste. Meanwhile, the amount of carbon dioxide absorbed onto the OPC was minimal at the same activator concentration, indicating that the AABFS actively absorbed carbon dioxide as a result of the carbonation reaction on its surface. However, the carbon dioxide absorption capacity and rate decreased as the activator concentration increased, because a high concentration of the activator promoted a hydration reaction and formed a dense internal structure, which was confirmed by SEM analysis. The results of the XRF analyses showed that the CaO ratio increased after the carbon dioxide absorption. CONCLUSIONS : The experimental results confirmed that the AABFS was capable of absorbing large amounts of carbon dioxide, suggesting that it can be used as a dry absorbent for carbon capture and sequestration and as a feasible alternative to OPC. In the formation of AABFS, the activator concentration affected the hydration reaction and changed the surface and internal structure, resulting in changes to the carbon dioxide absorption capacity and rate. Accordingly, the activator ratio should be carefully selected to enhance not only the carbon capture capacity but also the physicochemical characteristics of the geopolymer.

• Journal of Plant Biotechnology
• /
• v.1 no.1
• /
• pp.1-7
• /
• 1999

Large-scale cultures of plant cell, tissue, and organ have been achieved by using BTBB. When different sized BTBBs (5 L, 20 L, 100 L, 300 L, and 500 L) were tested for the culture of yew cells (Taxus cuspidata Sieb. et Zucc.), cell growth increment reached to 94.5% in SCV after 24 days of culture with 30% of inoculation cell density. However, there were some variations in the production of taxol and its derivatives among the BTBBs of different size. Approximate 4 ㎎/l of taxol and 84 ㎎/l of total taxanes were obtained by using a 500L BTBB after 6 weeks of culture. With a 20L BTBB, about 20,000 cuttings of virus-free potatoes (cv. Dejima) could be obtained by inoculating 128 explants and maintaining 8 weeks under 16 hr light illumination. The frequency of ex vitro rooting of the cuttings revealed as more than 99% under 30% shade. By incorporating two-stage culture process consisting of multiple bulblet formation in solid medium and bulblet development in liquid medium, mass propagation of lily through bioreactor seemed to be possible. In the case of 'Marcopolo', the growth of mini-bulblets in BTBB was nearly 10 folds faster than that of the solid medium. Time course study revealed that maximum MAR yield of ginseng (Panax ginseng C. A. Meyer) in a 5 L and 20 L BTBB after 8 weeks of culture was 500 g and 2.2 ㎏, respectively. By cutting the MAR once and/or twice during the culture, the yield of root biomass could be increased more than 50% in fresh weight at the time of harvest. With initial inoculum of 500 g of sliced MAR in a 500 L BTBB, 74.8 ㎏ of adventitious root mass was obtained after 8 weeks of culture. The average content of total ginseng saponin obtained from small-scale and/or pilotscale BTBBs was approximately 1% per gram dry weight. Based on our results, we suggest that large-scale cultures of plant cell, tissue, and organ using BTBB system should be quite a feasible approach when compared with conventional method of tissue culture.

• The Journal of Engineering Geology
• /
• v.10 no.1
• /
• pp.1-12
• /
• 2000

Heaving of road and subsidence of slope took place at the Wiri region of the local highway 999 in Gyeongsangbukdo, Korea after heavy rain in the next year of construction. Although the state government had performed remedial treatments by reducing the angle and the height of the slope, deformation had never stopped. Therefore, we have preformed the analysis of deformation and stabilityof the slope. Study area consists of the Cretaceous shale, siltstone and sandstone and two faults are found. The major deformation occurred by sliding of rock mass along faults after heavy rain because not only thepore pressure at the fault plane and the unit weight of sliding mass increased, but did the shearstrength of saturated fault clay become very low. The decrease in shear strength of saturated fault clayis the major factor among the reasons for deformation. Numerical simulations using limit equilibriummodel, finite difference model and finite element model were performed for eight cross sections.Although safety factors are above 1.7 during the dry season, they become below 1.0 when groundwaterlevel raises to surface. The maximum displacement is about 15-3Ocm. However, safety factors increasedto above 2.4 and the maximum displacement is below 2.08cm after remedial treatment, Indicating thatthe slope becomes stable.

• Journal of the Korean Applied Science and Technology
• /
• v.12 no.2
• /
• pp.121-130
• /
• 1995

This project has been worked out for isolation of EPA-producing bacteria from marine source of sea water, sea sediment and intestinal contents eviscerated from some red-muscle fish such as mackerel, horse-mackerel and spike fish. The samples were precultured on the media of PPES-II glucose broth and then pure-cultured on Nutrient agar and P-Y-M glucose. Lipids extracted from those bacterial mass collected by centrifugation were analysed in terms of lipid class and fatty acid composition. The results are resumed as follows : 1. 112 strains from sea water and 76 strains from sea sediment were tested for their EPA producing capability, but both strains of (SA-67 and SA-91) from the former and four strains(SS-35, 37, 51 and 71) from the latter have been proved to produce EPA above the level of 2% of total fatty acids. The strains such as GS-11, 29, 31, HM-9, 29, B-18, 33, 107, YL-129, 156, 203, 77, 104 and 256 which were isolated from fish intestinal contents, have also produced EPA at higher level than 2% of total fatty acids. 2. Contents of total lipids extracted from the cultures of these strains grown at $25^{\circ}C$, range from 2.8% to 6.9% (on dry weight %), and they are mainly composed of polar lipids($40.9{\sim}52.9%$) such as phosphatidyl glycerol($^{+}cardiolipin$)(?) and phosphatidyl ethanolamine ($33.8{\sim}40.0%$), with smaller amount of free fatty acid ($11.2{\sim}20.2%$). 3. EPA was isolated from a mixture of fatty acid methyl esters obtained from the lipid of each strain by HPLC in silver-ion mode and was identified by GC-Mass spectrometry. 4. The strains of SW-91, GS-11, GS-29, HM-9, B-18 and YL-203 grown at $25^{\circ}C$ have a level of 5% EPA in their total fatty acids, and the GS-11 and HM-9 strains show a tendency of increase in the EPA level with an increase of growth temperature.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.6
• /
• pp.530-537
• /
• 2011

The purpose of this study is to examine material performance of fiber reinforced cement composite for mass production. It is necessary to manufacture SHCC(Strain Hardening Cement Composite) by batch plant for field application and mass production. For the study, a mock-up test of SHCC manufactured in the batch plant was conducted, and the performance was compared with SHCC manufactured in the laboratory. Assessment items were freshness and hardening properties. Specifically, direct tensile test machine was used for performance verification of SHCC. As a result, there was a tendency of less satisfactory fiber dispersion and performance of strain hardening compared with the performance of SHCC manufactured in the laboratory. To address this, dry mixing and mortar mixing time should be increased compared to laboratory mixing, and injection time of an agent such as a water reducing agent should be properly controlled according to mixing combination, or the capacity to secure dispersion and homogeneity of material.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3D
• /
• pp.413-420
• /
• 2011

An experiment was conducted to suggest the road pavement material combining wooden chip crushed from little useful roots and branches from logging sites or wood waste from construction sites with urethane resin. For the specimen, the mass ratio of urethane resin to construction wood waste chip/lumber waster chip was set to three different levels of 0.5, 0.75, and 1.0, which was measured, mixed with mixer, and molded; 7 days after, tensile strength test, elasticity test using golf balls and steel balls, permeability coefficient measurement, and flammability test were executed. As the result, the tensile strength of the specimen at the dry state in the air exhibited the range of 0.2-1.1MPa, and there was no change after 7 days of aging. When submerged in water, however, the strength was partially diminished; the diminishing rate was greater for less urethane resin usage, and therefore it appears desirable to set the mass ratio of resin to the wood waste chip over 0.75 to consider the moisture intrusion by precipitation and such. As the result of elasticity test, the GB and SB coefficients of the specimen using wood waste chips and urethane resin were measured to be low at below 20%, exhibiting excellent elasticity as road pavement material. Also, the permeability coefficient was over 0.5mm/sec for specimens of all combinations, exceeding the standard value required after construction for permeable pavement material, and the flammability of wood-type pavement material was evaluated to have no practical issues.

• Journal of Plant Biotechnology
• /
• v.29 no.1
• /
• pp.37-40
• /
• 2002

Sweet potato is a crop vegetatively propagated by vine cuttings, an ineffective method for maintaining pathogene-free stock plants. As an alternative method, single-node cultures of virus-free plantlets derived from apical meristem in sweet potato (cv. Yulmi) was examined. Effective pH range, sugar concentration and nodal order were investigated to establish an in vitro mass propagation system with high quality virus-free stock plantlets to farmhouse. Although the plantlets grew at wide range of pH, the most effective pH of the medium was 4.8 in single-node cultures. High sugar concentration of 60∼80 g/L resulted in increased growth response in shoot length, root length, number of node, leaf area and fresh and dry weight of shoot and root, whereas reducing sugar contents below 6% was showed reduced growth response. The first node including meristem tip was the best for the rapid growth of plantlets and the other nodes also showed a very similar growth response. Uniform plantlet can be obtained massively at the same time by culture of single node except for the first node including meristem tip. In conclusion, the most effective pH range and sugar concentration of medium for the growth of plantlets via single-node cultures was 4.8, 60∼80 g/L respectively. The first node was the best for the rapid propagation of plantlets in nodal order.

• Journal of Energy Engineering
• /
• v.15 no.4 s.48
• /
• pp.243-249
• /
• 2006

An experimental study on the refrigerant-side pressure drop of slit fin an tube heat exchanger has been carried out. A comparison was made between the predictions of previously proposed empirical correlations and experimental data for the pressure drop on design conditions of condenser in micro-fin tube for R22 and Rl34a. Experiments were carried out under the conditions of inlet refrigerant temperature of $60^{\circ}C$ and mass fluxes varying from $150\;to\;250\;kg/m^{2}s$ for R22 and Rl34a. The inlet air conditions are dry bulb temperature of $35^{\circ}C$, relative humidity of 40% and air velocity varying from 0.68 to 1.43 m/s. Experiments show that pressure drop for R134a was $22{\sim}22.6%$ higher than R22 for the degree of subcooling $5^{\circ}C$ For the mass fluxes of $200{\sim}250\;kg/m^{2}s$, the deviation between the experimental and predicted values for the pressure drop was less than ${\pm}20%$ for R22 and Rl34a.