• Journal of Applied Reliability
• /
• v.12 no.2
• /
• pp.79-90
• /
• 2012

The torsion beam type of rear suspension has been adopted by most manufactures of small to medium front wheel drive passenger cars. Previous studies analyzed only the load characteristics of CTBA(the coupled torsion beam axle)'s components. This paper analyzed the results of measurement after measuring loads and displacements, angles when a car equipped with the coupled torsion beam axle is driving in various roads. The most important durability factors for CTBA part are the force and direction of rear CTBA trailing arm. If there are design changes, it was difficult to make a sensor and install each time for measuring the trailing arm forces. After analyzing the loading histories between body and chassis, we developed the transformation matrix that can be converted to mutual force. This paper also deals with the analysis of the force behavior through the analysis of the influence and correlation between the body and chassis parts of cars.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.6
• /
• pp.31-41
• /
• 2011

This study was conducted to predict future land-cover changes under climate change scenarios and to cluster analysis of regional land-cover characteristics. To simulate the future land-cover according to climate change scenarios - A1B, A2, and B1 of the Special Report on Emissions Scenarios (SRES), Dyna-CLUE (Conversion of Land Use Change and its Effects) was applied for modeling of competition among land-use types in relation with socioeconomic and biophysical driving factors. Gyeonggi-do were selected as study areas. The simulation results from 2010 to 2040 suggested future land-cover changes under the scenario conditions. All scenarios resulted in a gradual decrease in paddy area, while upland area continuously increased. A1B scenario showed the highest increase in built-up area, but all scenarios showed only slight changes in forest area. As a result of cluster analysis with the land-cover component scores, 31 si/gun in Gyeonggi-do were classified into three clusters. This approach is expected to be useful for evaluating and simulating land-use changes in relation to development constraints and scenarios. The results could be used as fundamental basis for providing policy direction by considering regional land-cover characteristics.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.2
• /
• pp.47-53
• /
• 2004

The salient pole rotor type single phase SRM (switched reluctance motor) uses radial and axial direction magnetic flux simultaneously. Therefore, the output power per unit volume is very high and the shaft length is shorter than other types of SRMs with the same output. Furthermore, it can be manufactured with low cost owing to its simple structure and driving circuit. The prototype was designed using the theory of the traditional rotating machine and 3D FEM analysis. On this paper, the experiment apparatus, which includes the fabricated prototype in previous researches, was fabricated to measure the current and voltage of the prototype. Then the flux linkage, inductance and magnetic co-energy were calculated using the experimental results. Finally, the measured magnetic co-energy was compared with the simulated magnetic co-energy.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.135-141
• /
• 2015

PURPOSES : While driving, drivers are usually limited in communicating with others except for using the horn. Excessive use of the horn may cause noise pollution, quarrels between drivers and pedestrians, damage, etc. This study developed a methodology for environmental adaptation and improvements of vehicle horns. METHODS: In this study, we performed a literature review of previous studies and related technologies regarding the overuse and damage of the horn. The proposed methodology employed the paired comparison method, as well as the semantic differential method. These methods can consider various vehicle horns, such as the Sport Utility Vehicle(SUV) Horn, Van Horn, and Buzzer. In addition, we conducted a factor analysis in order to provide a direction for improvement of future horns. This research provides a means of complimenting existing intellectual property related to vehicle horns. RESULTS: As a result, the most preferred of the selected horns were the Buzzer at 86.7%. In addition, based on the factor analysis, the horns could be classified into pleasantness and comfort factors. The results indicate a positive reaction for various vehicle horns. The horn type and size of the process control have been properly developed considering the position of the vehicle and the surrounding noise measurements. CONCLUSIONS : Based on the proposed methodology, public and private sectors can use fundamental data for reasonable traffic-noise control policies.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.687-690
• /
• 2000

Lately, many studies have been progressed for the protection human's lives and property as holding in check accidents happened by human's carelessness or mistakes. One part of these is the development of an autonomouse vehicle. General control method of vision-based autonomous vehicle system is to determine the navigation direction by analyzing lane images from a camera, and to navigate using proper control algorithm. In this paper, characteristic points are abstracted from lane images using lane recognition algorithm with sobel operator. And then the vehicle is controlled using two proposed auto-steering algorithms. Two steering control algorithms are introduced in this paper. First method is to use the geometric relation of a camera. After transforming from an image coordinate to a vehicle coordinate, a steering angle is calculated using Ackermann angle. Second one is using a neural network algorithm. It doesn't need to use the geometric relation of a camera and is easy to apply a steering algorithm. In addition, It is a nearest algorithm for the driving style of human driver. Proposed controller is a multilayer neural network using Levenberg-Marquardt backpropagation learning algorithm which was estimated much better than other methods, i.e. Conjugate Gradient or Gradient Decent ones.

• Journal of Broadcast Engineering
• /
• v.20 no.3
• /
• pp.440-448
• /
• 2015

A pedestrian collision warning system which makes a judgement of pedestrian's intention to help avoiding hitting accidents is proposed. This system uses the image sequences obtained from a car black box as well as vehicle's speed obtained from a GPS. It detects pedestrians, if any, based on the Histogram of Gradient method and extracts several information such as the pedestrian's relative positions, the direction of motion vectors, and distance between vehicle and pedestrian . A fuzzy logic based on these extracted information is applied to analyze the pedestrian's safety levels. When the safety level is determined to be danger, an alarm is triggered to the driver. The performance of the proposed algorithm is tested under various driving scenarios, which shows it works successfully in real-time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.8 s.251
• /
• pp.897-905
• /
• 2006

This study considers an experimental design of disturbance compensation control to improve stabilization performance of main battle tanks. An adaptive non-parametric design technique based on the Filtered-x Least Mean Square(FXLMS) algorithm is applied in the consideration of model uncertainties. The optimal compensator is designed by two-step design procedures: determination of frequency response function of the disturbance compensator which can cancel the disturbance of series of single harmonics by using the FXLMS algorithm and determination of the compensator polynomial which can fit the frequency response function obtained in the first step optimally by using a curve fitting technique. The disturbance compensator is applied to a simple experimental gun-torsion bar-motor system which simulates gun driving servo-system. Along with experimental results, the feasibility of the proposed technique is illustrated. Experimental results demonstrate that the proposed control reduces the standard deviation of stabilization error to 47.6% that by feedback control alone. The directional properties of the FXLMS Algorithm such as the direction of convergence and its convergence speed are also verified experimentally.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.1084-1087
• /
• 1997

In this paper, we developed the micro NCT system for punching the thin plates, which is driven is driven by the standalone type microprocessor. In order to adjust the alignment between the punch and die in-situ punching procedures, the non-contact type laser sensor for measuring the burr and micro-driving system for punching die with using the differential screw are developed. The height of burr in four directions in the punched hole of test specimen are measured, and the measured data are transferred to the personal computer by RS232C serial communication technology. In the personal computer, by using the graphic user interface type monitoring program and data handling procedures which includes the filtering algorithms, the direction and length of movement of the die position is decided and these data are transferred back to the microprocessor. The microprocessor drives the micro positioning stage based on these data. Even if this method is not a perfect solution for the in-situ alignment in micro punching, but this alignment methodology is accomplished in the same stage just after the punching that we hope to solve the alignment problem in the punching system based on this technology.

• Fire Science and Engineering
• /
• v.25 no.5
• /
• pp.32-38
• /
• 2011

Amphibious possible, and good fuel economy, so as leisure and transport has increased the use of hovercraft. Fire started in Korea, the prevalence is increasing in demand as the trend has been increasing steadily. In this paper, the hovercraft's forward and backward direction can be controlled in order to free the reverse bucket control system was developed. Control due to development by promoting the flow of air and turn right, turn left and easy to reverse the life-saving and stable at high speed, etc. has made possible the operation of hovercraft. The controller for the stability and fast response Fuzzy-PID method was used. To prove the validity of the proposed controller in Matlab simulation and the actual delivery at the firehouse, built into a model for the demonstration test was performed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.3
• /
• pp.179-186
• /
• 2015

In this paper, a novel lateral control system is proposed for the purpose of improving lane keeping performance which is independent from GPS signals. Lane keeping is a key function for the realization of unmanned driving systems. In order to obtain this objective, a vision sensor based real-time lane detection scheme is developed. Furthermore, we employ a data fusion along with a real-time steering angle of the test vehicle to improve its lane keeping performance. The fused direction data can be obtained by an IMU sensor and vision sensor. The performance of the proposed system was verified by computer simulations along with field tests using MOHAVE, a commercial vehicle from Kia Motors of Korea.