• 터널과지하공간
• /
• 제17권3호
• /
• pp.216-224
• /
• 2007

화약의 동적 충격에너지를 이용하는 발파굴착은 매우 효율적인 터널굴착방법이다. 그러나 진동과 암소음 등의 발파공해가 발생하는 문제점이 있다. 최근 연구를 통해 노치공을 이용한 선균열 암굴착방법은 발파공해와 터널의 여굴을 상당히 줄일 수 있는 것으로 확인되었고 이에 따라 본 연구에서는 노치발파공의 성형을 위한 노치장비개발에 관한 연구를 수행하였다. 노치공을 효율적으로 성형하기 위해 노치비트의 길이, 높이 등을 다양하게 변화시켜 실험을 수행하여 최적화하였고, 천공속도, 천공정밀도를 높이기 위한 천공비트, 노치비트, 아답타, 노치 가이드로 이루어진 노치비트 시스템을 개발하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.177-182
• /
• 1997

The purpose of this study is to analyze how tools, guide bush type and the change of cutting speed have effects on the diameter of cutting hole, surface roughness of workpiece and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. (1) The diameter was expanded for 25${\mu}{\textrm}{m}$ at the first section and then was reduced 0${\mu}{\textrm}{m}$ and 15${\mu}{\textrm}{m}$ respectively at the 10m and 20m section comparing to the diameter of tool with respect to the variation of cutting length. (2) It was proved that roughness was below 12S for the whole section of cutting length. (3) The roundness has been below 12${\mu}{\textrm}{m}$. Regarding the polygon phenomenon, it has bee proved that not only uneven number of angle but also even number (quadrilateral, elliptical) of angle were made. (4) Variation of diameter, surface roughness of workpiece and roundness turned out to ve the best at 70m/min of cutting speed, 0.15mm/rev of feed.

• 한국정밀공학회지
• /
• 제2권2호
• /
• pp.43-59
• /
• 1985

In relation to the machinability of drilling operation, experiments were made to investigate the effect of cutting condition on static as well as dynamic cutting resistances in cutting plane carbon steel (SM 45 C) with H.S.S. twist drills. The results were as follows. 1) The static cutting resistances on carbon steel can practically be calculated by the following equations which were derived from experimental result. The deviation from the experimental values was less than 8% and 13% for cutting torque and thrust respectively. For cutting torque M: M=0.019 $H_B\;{f^{0.68}d^{1.68}$ For thrust T: T=0.400406 $r^{0.6}d^{0.68}$ + 0.1835 $H_BC^2$(where $H_B$: Brinnel hardness) 2) The static components of cutting resistance are increased exponentially with increasing drill diameter and feed rate. On the effect of drill diameter, the dynamic components of torque are decreased with increasing dirll diameter because of rigidity, the dynamic components of thrust being not effected with the changes. 3) As feed rates increase, the dynamic components of torque rather decrease although its changes on thrust components are unstable. 4) The static components of cutting resistance and dynamic component of torque are slightly decreased in accordance with the increase of spindle speed although its dynamic thrust components are not effected by the spindle speed.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.37-43
• /
• 2005

Real time monitoring of exit burr formation is critical in manufacturing automation. In this paper, acoustic emission (AE) was used to detect the burr formation during drilling. By using wavelet transform (WT), AE data were compressed without unnecessary details. Then the transformed data were used as selected features (inputs) of a back-propagation artificial neural net (ANN). In order to validate the in process AE monitoring system, both WT-based ANN and cutting condition (cutting speed, feed, drill diameter, etc.) based ANN outputs were compared with experimental data.

• 융복합기술연구소 논문집
• /
• 제4권2호
• /
• pp.41-45
• /
• 2014

Micro fabrication technologies of aluminium have been required to satisfy many demands in technology fields. Pulsed laser beam machining can be an alternative method to accomplish the micro machining of aluminium. Pulsed laser beam can be applied to micro machining such as micro drilling and milling. Using pulsed laser beam, the machining characteristics of aluminium in micro drilling and milling were investigated according to average power, repetition rate, moving speed of spot. The laser beam machining with the optimal conditions can achieve precise micro figures. As a result, micro pattern, text and structures on aluminium surface was successfully fabricated by pulsed laser beam machining.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.513-518
• /
• 1999

In this study, geometrical similarity conditions for drills of various diameters are discussed. The effect of geometrical similarity on the chip shape and forces of different sized conventional drills has been experimentally confirmed. Drilling tests are carried out for SM45C by using the conventional HSS drills. The torque and thrust forces are measured and compared with those chip forms. Chip shape in drilling are affected by three factors being flow angle, side and up curl of the chip. It is found that the feedrate and drill diameter are more affected than cutting speed on the chip form and cutting forces. The similarity conditions gives easily to estimate the chip shape, the thrust and the torque for drills of different diameters.

• 한국생산제조학회지
• /
• 제9권6호
• /
• pp.118-126
• /
• 2000

In this study, geometrical similarity conditions for drills of various diameters are discussed. The effect of geometrical similarity on the chip shape and forces of different sized conventional drills has been experimentally confirmed. Drilling tests are carried out for SM45C by using the conventional HSS drills. The torque and thrust forces are measured and compared with those chip forms. Chip shape in drilling are affected by three factors being flow angle, side and up curl of the chip. It is found that the feedrate and drill diameter are more affected than cutting speed on the chip form and cutting forces. The similarity conditions gives easily to estimate the chip shape, the thrust and the torque for drills of different diameters.

• Current Optics and Photonics
• /
• 제3권5호
• /
• pp.451-457
• /
• 2019

Laser processing using holograms can greatly improve processing speed, by spatially distributing the laser energy on the target material. However, it is difficult to reconstruct an image with arrays of closely spaced spots for laser processing, because the specklelike interference pattern prevents the spots from getting close to each other. To resolve this problem, a line target was divided in two, reconstructed with orthogonally polarized beams, and then superposed. Their optical reconstruction was performed by computer-generated holograms and a pulsed laser. With this method, we performed two-dimensional (2D) laser drilling of polyimide film, with a kerf width of $20{\mu}m$ and a total processing length of 20 mm.

• Composites Research
• /
• 제24권4호
• /
• pp.23-28
• /
• 2011

최근 항공용 재료 산업 분야에서 널리 사용되고 있는 CFRP의 활용이 증가되고 있다. 하지만, CFRP와 같은 복합재료 부품의 결합 시에 단점이 있다. 복합재료를 이용한 다양한 구조를 제조하기 위해선 많은 홀 가공이 필요하다. 일반적으로 CFRP 홀 가공시 내구성이 매우 강한 polycrystalline crystalline diamond (PCD) 드릴을 사용한다. 하지만, 단가가 비싸고 가공 속도가 느리기 때문에 내구성은 PCD 드릴에 비해 약하나 드릴 형상 변화를 통해 가공 속도를 조절 할 수 있고, 비교적 가격이 저렴한 chemical vapor deposition (CVD) 다이아몬드 코팅 드릴의 사용량이 증가 되고 있다. 본 연구에서는. PCD 드릴과 CVD 다이아몬드 코팅 드릴의 홀 가공성을 비교 평가하였다. 먼저, 홀 가공 조건 식 (날당 이송량, 절삭 속도)을 이용하여 CFRP 홀 가공성을 평가했으며, CFRP 가공 시 드릴링 과정에서 발생하는 시편 내부의 열적 손상 정도를 비교했다. 열화상 카메라 촬영한 홀 가공 시 발생되는 온도를 이용한 경험식을 만들어 두 드릴의 발열 정도에 따른 홀 가공성을 비교 평가하였다. 또한, 홀 가공 시 발생하는 칩(chip) 배출 여부에 따른 홀 내부의 상태를 평가하여 CVD 다이아몬드 코팅 드릴과 PCD 드릴의 CFRP 홀 가공성을 비교했다. 전반적으로 PCD 드릴의 홀 가공성이 CVD 다이아몬드 드릴에 비해 우수한 성능을 나타냈지만, 홀 생성 속도는 CVD 다이아몬드 드릴이 PCD 드릴에 비해 빠른 결과를 나타냈다.

• 한국해양공학회지
• /
• 제16권6호
• /
• pp.60-64
• /
• 2002

This paper describes the machining characteristics of the MoSi$_2$--based composites through the process of electric discharge drilling with various tubular electrodes. In addition to hardness characteristics, microstructures of Nb/MoSi$_2$laminate composites were evaluated from the variation of fabricating conditions, such as preparation temperature, applied pressure, and pressure holding time. MoSi$_2$-based composites have been developed in new materials for jet engines of supersonic-speed airplanes and gas turbines for high-temperature generators. These high performance engines may require new hard materials with high strength and high temperature-resistance. Also, with the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material. The tool electrode is almost -unloaded, because there is n direct contact between the tool electrode and the work piece. By combining a non-conducting ceramic with more conducting ceramic, it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and MoSi$_2$ powder was an excellent strategy to improve hardness characteristics of monolithic MoSi$_2$. However, interfacial reaction products, like (Nb, Mo)SiO$_2$and Nb$_2$Si$_3$formed at the interface of Nb/MoSi$_2$, and increased with fabricating temperature. MoSi$_2$composites, with which a hole drilling was not possible through the conventional machining process, enhanced the capacity of ED-drilling by adding MbSi$_2$, relative to that of SiC or ZrO$_2$reinforcements.