• 한국지열·수열에너지학회논문집
• /
• 제17권1호
• /
• pp.23-32
• /
• 2021

Conventional wind power generators have limited installation sites due to low efficiency due to reverse resistance or high cut-in speed. To compensate for these problems, this study proposed another new type of tilting wind turbine. The key to this method is the structural design of a cylindrical cam with a guide groove that allows the blade to tilt. As the blade rotates by the cam, it tilts according to the angle. In the section that generates torque by receiving drag, the blade is made perpendicular to the wind. And it is a structure that creates a parallel state with the wind in the section where reverse resistance occurs. We prepared six types of cams considering the length of the section subject to drag, reverse resistance, tilting section. The performance was analyzed as the maximum value of the output, torque coefficient, and efficiency coefficient, which is indicated by setting different wind speed and low TSR.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.292-297
• /
• 1997

The rattle noise is the most significant in many kinds of manual gearbox noises, which is generated at the idle stage of the engine operation. The main torsional vibration source of the driveline is the fluctuation of the engine torque. The gear rattle is impacts generating in the backlash of the free gear due to this torsional vibration. Many researchers reported the clutch torsional characteristic optimization method to reduce the idle gear rattle but only few of them give sufficient consideration to the system parameters like gear backlash, drag torque, system inertia, inertia distribution, engine torque fluctuation, idle engine rotation speed, and accessory load. This paper pays attention to the gear impact mechanism and system design parameters to reduce the idle gear rattle with computer simulation.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.561-569
• /
• 2000

The purpose of this study is to construct a testing equipment with which several characteristics of the domestically developed swashplate type axial piston motor can be tested and to develop a software with which the data from experiment can be stored and can be applied. The results of the study are as follows; 1) The leakage flow and the torque of the motor being stopped is propotional to supply pressure and their relation can be showed by linear equations. 2) The motor movement is not smooth below 50 rpm but it moves smoothly up 170 rpm. 3) When the motor starts or stops, the pressure rise ratio effects decisively to the max. torque.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.183-190
• /
• 2016

Engine torque is transferred to the transmission where drag torque is minimized improving fuel efficiency. This is particularly true in a wet clutch pack. This study measures slip friction when the wet clutch pack in a DCT (Dual-Clutch Transmission) is disengaged, and the friction pads are slipping. Shudder engagement velocity, and applied forces can be measured under various working conditions through these torque transfer experiments. Test results demonstrate that the design parameters, and engagement conditions of wet clutch packs can be optimized to reduce shudder and frictional vibration during engagement in a dual clutch transmission.

• Wind and Structures
• /
• 제38권5호
• /
• pp.341-354
• /
• 2024

This paper presents a theoretical method to deal with the aerodynamic performance and pitch optimization of the horizontal axis wind turbine blades at low wind speeds. By considering a blade element, the functional relationship among the angle of attack, pitch angle, rotational speed of the blade, and wind speed is derived in consideration of a quasi-steady aerodynamic model, and aerodynamic loads on the blade element are then obtained. The torque and torque coefficient of the blade are derived by using integration. A polynomial approximation is applied to functions of the lift and drag coefficients for the symmetric and asymmetric airfoils respectively, where specific expressions of aerodynamic loads as functions of the angle of attack (which is a function of pitch angle) are obtained. The pitch optimization problem is investigated by considering the maximum value problem of the instantaneous torque of a blade as a function of pitch angle. Dynamic pitch laws for HAWT blades with either symmetric or asymmetric airfoils are derived. Influences of parameters including inflow ratio, rotational speed, azimuth, and wind speed on torque coefficient and optimal pith angle are discussed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.380-391
• /
• 2014

In this study, the scale effect on the performance of the podded propeller of tractor type is investigated. Turbulent flow computations are carried out for Reynolds numbers increasing progressively from model scale to full scale using the CFD analysis. The result of the flow calculation for model scale Reynolds numbers agrees well with that of the experiment of a large cavitation tunnel. The existing numerical analysis indicates that the performance of the podded propeller blades is mainly influenced by the advance coefficient and relatively little by the Reynolds number. However, the drag of pod housing with propeller in operation is different from that of pod housing without propeller due to the acceleration and swirl of propeller slipstream which is altered by propeller loading as well as the pressure recovery and friction according to Reynolds number, which suggests that the pod housing drag under the condition of propeller in operation is the key factor of the scale effect on the performance between model and full scale podded propellers. The so called 'drag ratio', which is the ratio of pod housing drag to total thrust of podded propeller, increases as the advance coefficient increases due to accelerated flow in the slipstream of the podded propeller. However, the increasing rate of the drag ratio reduces continuously as the Reynolds number increases from model to full scale progressively. The contribution of hydrodynamic forces, which acts on the parts composed of the pod housing with propeller operating in various loading conditions, to the thrust and the torque of the total propeller unit are presented for a range of Reynolds numbers from model to full scales.

• 한국추진공학회지
• /
• 제22권1호
• /
• pp.58-65
• /
• 2018

초고속 비행체의 성능을 향상시키기 위해 비행체 선두부에 대한 연구가 다양하게 수행되고 있다. 본 연구에서는 초음속 영역에서 역분사 공기 제트를 활용하여 유동 특성 및 항력 감소에 대한 실험 연구를 수행하였다. 고속카메라를 활용한 쉴리렌 가시화 방법으로 분사 유동을 가시화 하였으며, 토크센서를 이용해 분사 압력 조건에 따른 항력 변화를 측정하였다. 측정 결과, 분사 압력비 1.58 ~ 1.70 조건에서 비정상 상태의 유동이 정상 상태로 변화하였으며, 역분사 공기 제트의 분사 압력이 높을수록 항력이 감소하는 경향을 보였다.

• Wind and Structures
• /
• 제22권5호
• /
• pp.595-616
• /
• 2016

Providing high starting torque and efficiency simultaneously is a significant challenge for vertical axis wind turbines (VAWTs). In this paper, a new approach is studied in order to modify VAWTs performance and cogging torque. In this approach, J-shaped profiles are exploited in the structure of blades by means of eliminating the pressure side of airfoil from the maximum thickness toward the trailing edge. This new profile is a new type of VAWT airfoil using the lift and drag forces, thereby yielding a better performance at low TSRs. To simulate the fluid flow of the VAWT along with J-shaped profiles originated from NACA0018 and NACA0030, a two-dimensional computational analysis is conducted. The Reynolds Averaged Navier-Stokes (RANS) equations are closed using the two-equation Shear Stress Transport (SST) turbulence model. The main objective of the study is to investigate the effects of J-shaped straight blade thickness on the performance characteristics of VAWT. The results obtained indicate that opting for the higher thickness in J-shaped profiles for the blade sections leads the performance and cogging torque of VAWT to enhance dramatically.

• 제어로봇시스템학회논문지
• /
• 제11권8호
• /
• pp.688-695
• /
• 2005

This paper describes dynamic manipulability analysis of robotic arms moving in viscous fluid. The manipulability is a functionality of manipulator system in a given configuration under the limits of joint ability with respect to the task required to be performed. To investigate the manipulability of underwater robotic arms, a modeling and analysis method is presented. The dynamic equation of motion of underwater manipulator is derived based on the Lagrange-Euler equation considering with the hydrodynamic forces caused by added mass, buoyancy and hydraulic drag. The hydrodynamic drag term in the equation is established as analytical form using Denavit-Hartenberg (D-H) link coordination of manipulator. Two analytical approaches based oil manipulability ellipsoid are presented to visualize the manipulability of robotic arm moving in viscous fluid. The one is scaled ellipsoid which transforms the boundary of joint torque to acceleration boundary of end-effector by normalizing the torques in joint space, while the other is shifted ellipsoid which depicts total acceleration boundary of end-effector by shifting the ellipsoid as much as gravity and velocity dependent forces in work space. An analysis example of 2-link manipulator with proposed analysis scheme is presented to validate the method.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 V
• /
• pp.2713-2716
• /
• 2003

This paper presents a dynamic manipulability analysis method of the limb moving in viscous fluid. The key idea of the presented method is that the boundary of joint velocity can be converted to the velocity-dependant dynamic manipulability polytope through the coriolis, centrifugal and drag terms in dynamic equation. The velocity-dependant dynamic manipulability polytope is added to the inertial and restoring force manipulability polytope to get overall manipulability polytope of the limb moving in the fluid Each of the torque and velocity bounds arc considered in the infinite norm sense in joint space, and the drag force of a limb moving in fluid viscous is modeled as a quadratic form An analysis example with proposed analysis scheme is presented to validate the method.