• Journal of the Korean Society of Industry Convergence
• /
• v.21 no.6
• /
• pp.265-271
• /
• 2018

DC-DC buck converter is a critical building block in the power management integrated circuit (PMIC) architecture for the portable devices such as cellular phone, personal digital assistance (PDA) because of its power efficiency over a wide range of conversion ratio. To ensure a safe operation, avoid unexpected damages and enhance the reliability of the converter, fully-integrated protection circuits such as over voltage protection (OVP), under voltage lock out (UVLO), startup, and thermal shutdown (TSD) blocks are designed. In this paper, these three fully-integrated protection circuit blocks are proposed for use in the DC-DC buck converter. The buck converter with proposed protection blocks is operated with a switching frequency of 1 MHz in continuous conduction mode (CCM). In order to verify the proposed scheme, the buck converter has been designed using a 180 nm CMOS technology. The UVLO circuit is designed to track the input voltage and turns on/off the buck converter when the input voltage is higher/lower than 2.6 V, respectively. The OVP circuit blocks the buck converter's operation when the input voltage is over 3.3 V, thereby preventing the destruction of the devices inside the controller IC. The TSD circuit shuts down the converter's operation when the temperature is over $85^{\circ}C$. In order to verify the proposed scheme, these protection circuits were firstly verified through the simulation in SPICE. The proposed protection circuits were then fabricated and the measured results showed a good matching with the simulation results.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.13-19
• /
• 1995

A dual purpose robot automation system is developed for both arc welding and spot welding by one robot within a cell. The need for automation of both arc welding and spot welding processes is urgent while the production volume is not so big as to accommodate separate stations for the two processes. Also, space is too narrow for separate stations to be settled down in the factory. A spot welding robot is chosen and the functions for arc welding are implemented in-house at cost of advanced functions. For the spot welding, a single pole type gun is used and the robot has to push down the plate to be wolded, which causes the robot positioning error. Therefore, position error compensation algorithm is developed. The basic functions for the arc welding processes are implemented using the digital I/O board of robot controller, PLC, and A/D conversion PCB. The weaving pattern is taught in meticulously by manual teach. A fixture unit is also developed for dual purpose. The main aspects of the system is presented in this paper especially in the design and implementation procedure. The signal diagrams and sequence logic diagrams are also included. The outcome of the dual purpose welding cell is the increased productivity and good production stability which is indispensable for production volume prediction. Also, it leads to reduction of manufacturing lead time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.661-668
• /
• 2004

A novel method to reject the spurious signals which are occurred at Weaver-type low-IF transmitter was proposed in this paper. The spurious signals are generated by the gain and phase imbalances of I/Q channel or imperfect characteristics of 90$^{\circ}$ phase shifter in local oscillator for I/Q channel source. By deriving the gain and phase-based functions from RF spurious signal with the channel imbalance information, the lie channel imbalances were deduced as functions with magnitude and sign dependent on I/Q channel imbalance degree. The proposed method compensates the estimated I/Q channel imbalances by correlation values between the down-converted signal obtained by squaring the output signal itself using a simple mixer and the modified baseband signal. By comparing two signals after A/D conversion, the magnitude and sign of each type of imbalances can be determined separately and simultaneously. Based on the I/Q channel imbalance compensation, the spurious signals can be reduced by adjusting the gain and phase values of I or Q channel signal. The way to estimate the channel imbalances of the up-conversion mixer was presented and verified by using theoretical derivations and computer simulations.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.6
• /
• pp.1217-1226
• /
• 2004

A psychrotrophic bacterial strain, Pseudomonas fluorescens BM07, synthesized unsaturated fatty acids (UFA) from fructose in response to lowering of growth temperature, and incorporated them into both polyhydroxyalkanoic acid (PHA) and membrane lipid. The blocking of PHA synthesis by adding 5 mM 2-bromooctanoic acid to the growth medium, containing 70 mM fructose, was found to be a useful means to profile the composition of membrane lipid by gas chromatography. As the growth temperature changed from 35 to $50^{\circ}C$, the total content of two UFA, 3-hydroxy-cis-5­dodecenoic acid ($C_{12:1}$) and 3-hydroxy-cis-7-tetradecenoic acid ($C_{14:1}$), in PHA increased from 31 to 44 $mol\%$. The growth at lower temperatures also led to an increase in the level of two major UFA, palmitoleic acid (C16:1 cis9) and cis-vaccenic acid (C18:1 cis11), in membrane lipid. A fraction of these membrane-lipid UFA was converted to their corresponding cyclopropane fatty acids (CFA). The CFA conversion was a function of culture time, exhibiting biphasic increase before and after entering the stationary phase. However, pH changes in growth media had no effect on the CFA conversion, which is contrary to the case of E. coli reported. The cells grown at $30^{\circ}C$ responded to a cold shock (lowering the medium temperature down to $10^{\circ}C$) by increasing the level of C16:1 cis9 and C 18: I cis II up to that of $10^{\circ}C$-grown control cells and concomitantly decreasing the relative level of cis-9,10­methylenehexadecanoic acid (the CFA converted from C16:1 cis9) from 14 to 8 $mol\%$, whereas the 10-grown cells exhibited little change in the lipid composition when exposed to a warmer environment of $30^{\circ}C$ for 12 h. Based on this one- way response, we suggest that this psychrotrophic strain responds more efficiently and sensitively to a cold shock than to a hot shock. It is also suggested that BM07 strain is a good producer of two unsaturated 3-hydroxyacids, $C_{12:1}\;and\;C_{141:1}$.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.279-285
• /
• 2008

The etherification of 2-naphthol with ethanol has been carried out over various solid acid catalysts. CNS, CNSWS, SCMS, MCF, and SBA-15 with and without sulfonic acid were used in this study as solid acid catalysts. The conversion of 2-naphthol and the selectivity of 2-naphthyl ethyl ether were obtained at reaction temperature = $180^{\circ}C$, $LHSV=1h^{-1}$, ethanol/2-naphthol molar ratio = 20 using a fixed-bed down flow reactor. The conversion of 2-naphthol and the selectivity of 2-naphthyl ethyl ether over silica group catalysts were higher than them over carbon group catalysts. The conversion of 2-naphthol was 70-90% and the selectivity of 2-naphthyl ethyl ether was more than 90% over silica group solid acid catalysts. It was performed XRD, SEM, TEM, and $NH_3-TPD$ to characterize solid acid catalysts.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.1
• /
• pp.32-37
• /
• 2004

The charge/discharge capacity of natural graphite anode in lithium secondary batteries was examined as a function of charge/discharge rate. When the natural graphite anode was galvanostatically cycled in the range of 0.0-2.0V $(vs.\;Li/Li^+)$, the charging capacity decreased with an increase in the charging rate, which is caused by an earlier approach to the charging cut-off (0.0 V) before the complete charging that is in turn caused by an ever-increasing overpotential at higher rates. Even if the overpotential of discharging reaction also increased at higher discharge rates, the discharging reaction took place in the range of 0.0-0.3 V that is far below the discharge cut-off (2.0 V). As a result, the discharge capacity was not affected by the discharge rate because all the lithium ions once intercalated are fully discharged even at high current condition. As the overpotential of lithium deposition reaction also increased at high current condition, the charge capacity of natural graphite could be enlarged by lowering the charging cut-off voltage below 0.0 V, There is, however, a limitation for the lowering of cut-off voltage because the resistance for lithium deposition is smaller than that of lithium intercalation into graphite. When the charge cut-off voltage was lowered down to -0.04 V under IC condition, lithium ions were inserted into graphite without lithium deposition such that the discharge capacity could be raised up to $11\%$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.29-36
• /
• 2009

In this paper, the design and implementation of LNA and down-mixer using 90 nm CMOS process are presented for 60 GHz band WPAN receiver. In order to extract characteristics of the transistor used to design each elements under the optimum bias conditions, the S-parameter of the manufactured cascode topology was measured and the effect of the RF pad was removed. Measured results of 3-stages cascode type LNA the gain of 25 dB and noise figure of 7 dB. Balanced type down-mixer with a balun at LO input port shows the conversion gain of 12.5 dB within IF frequency($8.5{\sim}11.5\;GHz$) and input PldB of -7 dBm. The size and power consumption of LNA and down-mixer are $0.8{\times}0.6\;mm^2$, 43 mW and $0.85{\times}0.85\;mm^2$, 1.2 mW, respectively.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.3
• /
• pp.10-15
• /
• 2010

The aim of this study was to analysis the Heating/cooling performance of Solar Window System built in apartments. The solar window is the idea to integrate daylight as a third form of solar energy into a PV/Solar Collector system and allows more control due to the possibility to close the reflectors. However, there can be a conflict between the desire for on one hand daylight and view and on the other hand optimal energy conversion for the PV/Solar Collector system. The process of this study is as follows: 1) The Solar Window system is designed through the investigation of previous paper and work. 2)The simulation program(ESP-r, Therm5.0, Window6.0) was used in energy performance analysis. The reference model of simulation was made up to analysis energy performance on Solar Window system. 3)Selected reference model(Floors:15, Area of Unit:$148.5m^2$) for heating/cooling energy analysis, Energy performance simulation with various variants, such as U-value of Solar Window system according to its position and angle. Consequently, When Solar Window system is equipped with balcony window of Apartment, Annual heating and cooling energy of reference model was cut down about 5%~11%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.65.2-65.2
• /
• 2010

The aim of this study was to analysis the Heating/cooling performance of Solar Window built in apartments. The solar window is the idea to integrate daylight as a third form of solar energy into a PV/Solar Collector system and allows more control due to the possibility to close the reflectors. However, there can be a conflict between the desire for on one hand daylight and view and on the other hand optimal energy conversion for the PV/Solar Collector system. The process of this study is as follows: 1) The Solar Window system is designed through the investigation of previous paper and work. 2)The simulation program(ESP-r, Therm5.0, Window6.0) was used in Heating/cooling performance analysis. The reference model of simulation was made up to analysis Heating/cooling performance on Solar Window. 3)Selected reference model(Floors:15, Area of Unit:$148.5m^2$) for heating energy analysis, Energy performance simulation with various variants, such as U-value of Solar Window system according to its position and angle. Consequently, When Solar Window system is equipped with balcony window of Apartment, Annual heating and cooling energy of reference model was cut down about 5%~11%.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.4
• /
• pp.373-378
• /
• 2002

In fuzzy inferencing, most of conventional fuzzy controllers have problems of speed down in floating point operations of fuzzy membership functions in (0,1) as compared with integer operations. Therefore, in this paper, we propose a high-speed fuzzy controller with only integer operations. In this, for fast fuzzy computations, we use a scan line conversion algorithm to convert lines of each fuzzy linguistic term to the set of the closest integer pixels. We also implement a GUI (Graphic User Interface) application program for the convenient environments to modify and input fuzzy membership functions.