• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.492-494
• /
• 1996

This paper describes a study on the series resonant inverter using the double full-bridge, and the output voltage of the proposed inverter is controlled by phase shift angle of the outputs of two inverters. These control schemes can be reduce the switching loss and EMI, etc, which the inverter is drived by auto following control of output frequency, because it is impossible for switching devices to be always turned on and off at zero voltage or zero current. Theoretical characteristics of the proposed double inverter circuit are compared with Pspice simulation and experimental results.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.6
• /
• pp.831-837
• /
• 2013

MEMS accelerometer provides a low cost alternative in retrieving the acceleration signal for motion sensing. Theoretically, displacement can be calculated by double integrate the acceleration signal. However, in practical, it could not be done in straight forward manner due to several factors that exist in the real world. This experiment focuses on the processes from practical accelerometer signal acquisition till the result of double integration for low frequency vertical motion.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1081-1085
• /
• 2015

In this paper a printed pair dipole antenna with double tapered microstrip balun for wireless communications is proposed. The proposed antenna consists of a pair arm of different sizes that is branched microstrip line and microstrip line with the ground plane on opposite side of the dielectric substrate plane. The proposed antenna is matched between the ground plane to the microstrip line by double tapered microstrip balun. This antenna obtains multi-band radiation frequency band. The impedance bandwidths for a reflection coefficient of VSWR ≤ 2 are about 1.01 GHz (2.35~3.336 GHz), 1.56 GHz (4.7~6.26 GHz) and 1.15GHz (6.85~8.0[GHz]). Additionally, the measurement peak gain is about 3.6 dBi. The proposed antenna is able to support wireless communication applications.

• Computers and Concrete
• /
• v.25 no.2
• /
• pp.133-144
• /
• 2020

This paper aims to study vibration characteristics of chiral and zigzag double-walled carbon nanotubes entrenched on Donnell shell model. The Eringen's nonlocal elastic equations are being combined with Donnell shell theory to observe small scale response. Wave propagation is proposed technique to establish field equations of model subjected to four distinct end supports. A nonlocal model has been formulated to explore the frequency spectrum of both chiral and zigzag double-walled CNTs along with diversity of indices and nonlocal parameter. The significance of scale effect in relevance of length-to-diameter and thickness- to- radius ratios are discussed and displayed in detail. The numerical solution based on this nonlocal Donnell shell model can be further used to predict other frequency phenomena of double-walled and multi-walled CNTs.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.410-417
• /
• 2012

In this paper, a direct current control method based on a one-cycle controller (DCOCC) for double frequency buck converters (DF buck) is proposed. This control method can make the average current through the high frequency and low frequency inductors of a DF buck converter equal. This is similar to the average current control method. However, the design of the loop compensator is much easier when compared with the average current control. Since the average current though the high frequency and low frequency inductors is equivalent, the current stress of the high frequency switches and the switch losses are minimized. Therefore, the efficiency of the DF buck converter is improved. Firstly, the operation principle of DCOCC is described, then the small signal models of a one cycle controller and a DF buck converter are presented based on the state space average method. Eventually, a system block diagram of the DCOCC controlled DF buck is established and the compensator is designed. Finally, simulation and experiment results are given to verify the correction of the theory analysis.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.3
• /
• pp.196-201
• /
• 2017

A cylindrical structure has a very long period of heave and pitch motion response in ocean waves. To obtain the dynamic stability of a cylindrical structure, it is necessary to obtain the suitable metacentric height (GM). However, in a structure with sufficient metacentric height, Mathieu instability can occur if the natural frequency of the heave motion is double the natural frequency of the roll and pitch motion. This study carried out numerical calculations and experiments for vertical-axis wind turbines with cylindrical floaters, which had three different centers of gravity. In the regular wave experiment, the divergence of the structure motion without yaw was observed when the natural frequency of the heave motion was double the natural frequency of the roll and pitch motion. In the irregular wave experiment, the motion spectra of the structures with the different centers of gravity were compared, and one was very high when the natural frequency of the heave motion was double the natural frequency of the roll and pitch motion.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.363-366
• /
• 1998

High frequency scattered fields by a double impedence wedge are computed. In the procedure of the computation, arbitrary impedence faces and wedge angles are considered. The diffraction coefficients for the single, double and triple diffraction mechanism are founded. The second-order and third-order diffracted fields are approximated via the extended spectral ray method and the modified Pauli-Clemmow method of the steepest descent. The maliuzhinets function which is very difficult to obtain accurate value is approximated by the Volakis's asymtotic expression. Numerical computations are performed for the various wedge angles and surface impedence values.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.461-464
• /
• 1999

Planar type thin film inductors have a potential for the application of miniaturized DC-DC converters. For those high current applications, the magnetic film with high current capability is required. The current capability of magnetic films is mainly determined from high saturation magnetization (4$\piM_s$) as well as large anisotropy field $(H_k)$. We fabricated a double rectangular spiral thin film inductor which consist of magnetic layer, coil and insulator. Highest inductance values as well as best frequency characteristics can be obtained from 5 MHz and quality factor exhibit about 7.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.1
• /
• pp.67-75
• /
• 1992

A new method of driving the PDP(Plasma Display Panel) was proposed and its characteristics were investigated. Applying high frequency non-discharge pulses to an auxiliary anode resulted an increased region of stable operation, decreased delay time and increased light intensity. It is suggested that PDP with DPM (Double Pulse Memory) drive technique improves the delay time, luminance, region of stable operation and luminous efficacy compared to PDP with PPM(Planar Pulse Memory) drive technique developed by NHK Lab. in Japan.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.436-440
• /
• 2014

To verity the effect of PCB plane layer to the output characteristics of the Switched Mode Power Supply (SMPS), this paper compared with a generic one-layer PCB and a double-side PCB. This paper specially focused on the voltage, the current and the high frequency noise of the output characteristic of the SMPS, using a double-side PCB which has same layout and was installed a ground plane on the opposite side. This double-side PCB was assembled by all same components which used on the SMPS using the single-side PCB. The experiment results show the SMPS using the ground plan PCB can efficiently reduce the high frequency noise to 50mV at 100MHz from 150mV in the single-side PCB. And the results also show the high harmonics frequency was reduced as well.