• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.4
• /
• pp.326-331
• /
• 2000

We have fabricated the field emitter arrays coated with diamond-like carbon (DLC) films that improved the field emission characteristics. The nitrogen doped DLC films are prepared by the filtered cathodic vacuum are (FCVA) tehnique. The activation energy of the nitrogen doped DLC films are derived from electrical conductivity measurements. The silicon field emission arrays (FEAs) were prepared by the VLSI technique. The turn-on field was rapidly decreasing and the emission current was remarkably increasing the DLC-coated FEAs than the non-coated silicon FEAs. In the nitrogen doped FEAs, the turn-on field decreased and the emission current increased with increasing the nitrogen found out the field emission current and the work function of the DLC-coated FEAs was remarkably decreased than that of the non-coated silicon FEAs. As nitrogen doping concentrations are increased the work function of FEAs is decreased and the field emission properties are improved in nitrogen doped DLC-coated FEAs. This phenomenon in due the fact that the Fermi energy level moves to the conduction band by increasing nitrogen doping concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.43-46
• /
• 2002

Ferroelectric Mg-doped SBT and Ti-doped SBT were successfully deposited on Pt/Ti/$SiO_2/Si$ substrate by using a sol-gel solution coating method. The solutions were prepared through out adding the metal alkoxide solutions to SBT solution. The typical hysteresis loop of the films was obtained at 5V. The measured $2P_r$ value were $16.50{\mu}C/cm^2$ for SBT, $18.98{\mu}C/cm^2$ and for Mg-doped SBT, and $17.10{\mu}C/cm^2$ for Ti-doped SBT at an applied voltage of 5V, respectively. And it is found that the leakage current densities are less than $10^{-7}A/cm^2$ when applied voltage is less than 10.8MV/cm, which indicates the excellent insulating characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.33-34
• /
• 2006

The effects of Ba and Ce addition has been investigated in YBCO prepared by trifluoroacetate (TFA) metalorganic depostition (MOD) method. Precursor solutions with cation ratios of Y:Ba:Cu:Ce = 1:2+x:3:x (x = 0, 0.05, 0.1 and 1.5) have been prepared by adding an excess amount of cerium and barium. Coated film was calcined at lower temperature and conversion heat treatment at temperature of $780{\sim}810^{\circ}C$. It has been shown that the critical current (Ic) of YBCO film was degraded by doping of Ba and Ce atoms. But Ic was increased as the amount of doped Ba and Ce content increased from 5 % to 15 %. It was observed that there was little increase of a flux pinning force with Ba and Ce addition in YBCO film prepared by TFA-MOD process.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1325-1326
• /
• 2007

We have demonstrated new functionalities of Ag doped chalcogenide glasses based on their capabilities as solid electrolytes. Formation of such amorphous systems by the introduction of silver via photo-induced diffusion in thin chalcogenide films is considered. The influence of silver on the properties of the newly formed materials is regarded in terms of diffusion kinetics and Ag saturation is related to the composition of the hosting material. Silver saturated is related to the composition of the hosting material. Silver saturated Ge-Ch glasses have been used in the formation of solid electrolyte which is the active medium in programmable metallization cell (PMC) devices. This paper concerns our more recent work on silver-doped germanium selenide electrolytes and describes the electrical characteristics of PMC devices made from these materials following annealing at $300^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.394-399
• /
• 1998

High power characteristics with vibration velocity were studied in $Pb(Y_{2/3}W_{1/3})O_3-Pb(Zr,Ti)O_3$(PYW-PZT) ceramics by using the constant current method. Young s modulus $Y_0^E$ and mechanical quality factor $Q_m$ are a function of the square of effective vibration velocity \upsilon_0$. The nonlinear proportional constants of the above functions indicate the degree of stability under the vibration level change. The stability of PYW-PZT ceramics estimated by these constants coincides with the results obtained through the heat generation. It was found that $Q_m$ was markedly decreased with increasing the vibration velocity, accompanying a lot of heat generation. The vibration hysteresis and dielectric loss according to the vibration velocity was reduced by doping $Fe_2O_3$to the ceramics. On the contrary, these losses was increased by doping $Nb_2O_5$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1192-1198
• /
• 2004

Hole transporting polymer(poly［N-(p-diphenylamine)phenylmethacrylamide］, PDPMA) was doped with nile red dye at various concentrations to study the influence of doping on the energy transfer during light emitting processes. Organic LEDs composed of ITO/blend(PDPMA -nile red)/ Alq$_3$/Al as well as thin films of blend(PDPMA -nile red)/ Alq$_3$ were manufactured for investigating photoluminescence, electroluminescence, and current-voltage characteristics. Atomic Force Microscopy was also used to observe surface morphology of the blend films. It was found that such doping. significantly influences the efficiency of the energy transfer from the Alq$_3$ layer to blended layer and the optical/electrical properties could be optimized by choosing the right concentration of the dye molecule. The results also showed a interesting correlation with the morphological aspect, i.e. the optimum luminescence at the concentration with the least surface roughness. When the concentration of nile red was 0.8 wt%, the maximum energy transfer could be achieved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.5-6
• /
• 2005

High performance SiGe heterostructure metal-oxide-semiconductor field effect transistors(MOSFETs) were fabricated using well-controlled delta-doping of boron and SiGe/Si heterostructure epitaxal layers grown by reduced pressure chemical vapor deposition. In this paper, we report 1/f noise characteristics of the SiGe MOSFETs measured under various bias conditions of the gate and drain voltages changing in linear operation regions. From the noise spectral density, we found that the gate and drain voltage dependence of the noise represented same features, as usually scaled with $f^1$. However, 1/f noise was found to be much lower in the device with boron delta-doped layer, by a factor of $10^{-1}\sim10^{-2}$ in comparion with the device fabricated without delta-doped layer. 1/f noise property of delta-doped device looks important because the device may replace bipolar transistors most commonly embedded in high-frequency oscillator circuits.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.41-42
• /
• 2006

Carbon nanotubes (CNTs) effects on physical properties of the liquid crystal and twisted nematic (TN) liquid crystal (LC) cells have been investigated. The minute doping of CNTs reduces rotational viscosity of the LC, and thus switching time of the TN cells is improved, especially in grey scale response time. In addition, the dielectric anisotropy and birefringence are not affected by such a small amount of CNT-doping and thus voltage-dependent transmittance remains the same.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.183-184
• /
• 2005

In this paper. a new small size Lateral Trench Electrode Power IGBT is proposed. The entire electrode of proposed LIGBT is placed in trench oxide. The forward blocking voltage of the proposed LIGBT is improved by 1.6 times with that of the conventional LIGBT. The forward blocking voltage of proposed LIGBT is 500V. At the same size. a increase of the forward blocking voltage of about 1.6 times relative to the conventional LIGBT is observed by using TMA-MEDICI which is used for analyzing device characteristics. Because the electrodes of the proposed device are formed in trench oxide. the electric field in the device are crowded to trench oxide. We observed that the characteristics of i the proposed device was improved by using TMA-MEDICI and that the fabrication of the proposed device is possible by using TMA-TSUPREM4.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.76-79
• /
• 2005

$Nd:YVO_4$ 연속발진 레이저(CW laser:Continuous wave laser)로 제작한 다결정 실리콘 박막의 이온도핑 효과를 조사하였다. PECVD로 증착한 비정질 실리콘 박막을 CW 레이저를 조사하여 결정화한 후 $B_2H_6$ 플라즈마 이온 도즈량을 변화시켜 이온 도핑을 하고 급속열처리 방법과 퍼니스 어닐링 방법으로 도펀트 활성화를 하였다. 이온 도핑된 CW 다결정 실리콘 박막의 이온 도즈량에 따른 판저항 변화를 비교하고, 급속열처리(RTA: Rapid Thermal Annealing)와 퍼니스 어닐링(FA: Furnace Annealing) 전후의 결정성 변화를 라만 스펙트럼(Raman spectrum) 을 통하여 분석하였다. 이온 도즈량이 증가함에 따라 판저항은 감소하고, 어닐링 후 이온 도핑에 의해 손상된 박막이 복원됨을 확인 할 수 있다.