• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1496-1503
• /
• 2005

The study on the lateral earth pressure is briskly preformed for various conditions such as type of retaining walls, ground condition, and type of supporting systems. It is not simple to determine the distribution of lateral earth pressure accurately, however, because the lateral earth pressure is affected by various factors. This study is performed to analyze the behavior of earth retaining walls for new excavation contacting with existing excavation by comparing with the site measuring values before and after new excavation. On the base of observation, the distribution of strut axial forces is similar to that of ganeral earth retaining walls, but strut axial forces is increased by removal of existing earth anchors. When new excavation is performed contacting with existing excavation, the axial force of strut is decreased because of soil exclusion in the behind walls, but that force is increased after new exeavation. The analysis result show that the installation of strut in middle part makes a effect to not only 1 adjacent strut, but 3-5 adjacent struts. Also during new excavation strut axial forces is decreased by relaxation of total earth retaining wall system.

• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.421-430
• /
• 1997

본 연구에서는 숏브라스트한 후 무기징크 페인트로 도장한 무기징크면, 연마면, 흑피면에 대하여 정적 및 피로시험을 수행하여 기존의 연구결과와 비교평가함으로써 마찰면의 표면상태에 따른 고장력볼트 마찰이음부의 정적 및 피로거동을 규명하고자 하였다. 본 연구의 목적을 달성하기 위하여 일련의 정적 및 피로시험을 실시하고 토크관리법의 타당성 평가, 미끄러짐계수의 도출, 도입축력의 감소률 규명, 피로강도의 평가, 마찰면의 압축력 분포 조사 등을 수행하였다. 본 실험결과와 기존 연구자들의 연구결과를 종합적으로 검토한 결과 볼트의 설계축력 도입을 위한 토크관리법은 타당하며, 시간경과 및 반복하중의 작용에 따른 축력감소율을 고려할 때 설계축력의 110%로 초기축력을 도입하도록 규정한 시방서 기준은 적합한 것으로 평가되었다. 시간경과에 따른 도입축력의 초기감소율은 경과시간의 상용로그에 비례하는 것으로 나타났으며, 도입직후 약 20시간이 경과하면 일정한 값으로 수렴되고 있음을 알 수 있었고 이들은 마찰면의 표면조도와는 상관관계가 없는 것으로 평가되었다. 미끄러짐계수는 연마면, 무기징크프라이머 도포면, 흑피면 순으로 크게 나타났으며 미끄러짐하중은 도입축력에 크게 좌우되나 도입축력이 크면 마찰면의 표면조도의 손상으로 인하여 미끄러짐계수가 작아져 도입축력과 미끄러짐하중 사이에는 선형적 비례관계가 성립되지 않음을 알 수 있었다. 마찰면의 압축력 분포를 조사한 결과 내측볼트 주변의 마찰면적이 외측볼트 주변보다 응력방향에 있어서 더 넓게 분포하고 있는 것을 알 수 있었으며, 이는 외측볼트로부터 마찰접합에서 지압접합으로 천이되고 있는 것으로 판단된다.

• Earthquakes and Structures
• /
• 제20권2호
• /
• pp.225-238
• /
• 2021

Supplemental passive dampers are widely employed to improve the structural performance of buildings under seismic excitations. Nevertheless, the added damping could be counter-productive if the axial forces induced by the damper reaction forces are not routed properly in the columns. A few researchers engaged to optimize the width-wise damper arrangement to improve the delivered path of the axial column forces. However, most of these studies are limited under the design-based seismic level and few of them has evaluated the collapse performance of buildings under strong earthquakes. In this paper, the strategic width-wise placement method of viscous dampers is explored regarding the building performance under collapse state. Two realistic steel buildings with different storeys are modelled and compared to explore higher mode effects. Each building is designed with four different damper arrangement scenarios based on a classic damper distribution method. Both a far-fault and a near-fault seismic environment are considered for the buildings. Incremental Dynamic Analysis (IDA) is performed to evaluate the probability of collapse and the plastic mechanism of the retrofitted steel buildings.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.169-176
• /
• 2005

Many RC building structures of multiple uses constructed in Korea have the irregularities of torsion and soft story at bottom stories. A typical irregular building was selected as prototype and shaking table tests were performed to investigate the seismic performance of this building. The objective of this study is to evaluate the correlation between the experimental and analytical responses of this irregular building structure subjected to the earthquake excitation by using OpenSees(Open System for Earthquake Engineering Simulation). The results of analyses simulate well the effect of axial forces on the shear force of column and axial deformation. However, some discrepancy between analytical and experimental results in the distribution of shear forces and overturning deformation were observed.

• 한국산학기술학회논문지
• /
• 제15권7호
• /
• pp.4611-4617
• /
• 2014

본 논문은 강접골조의 예비구조설계에서 부재력을 근사적으로 예측하기 위한 연구이다. 기둥간의 축력 분포를 선형으로 가정하는 캔틸레버법에서 기둥의 변곡점 위치를 부재의 중간으로 가정하는데 이것은 몇 개의 사례를 통해 행렬해석법과 비교한 바 오차가 매우 심하다는 것을 알 수 있다. 다양한 골조를 해석한 결과를 분석해보면, 부재력은 기둥과 보의 경간비, 단면2차모멘트비에 따라 달라짐을 알 수 있다. 본 연구에서는 기존의 방법과는 다른 방법으로 기둥의 부재력을 예측하는 방법을 제시하였다. 예제를 통하여 기존의 방법보다 향상된 해를 얻을 수 있었다.

• Computers and Concrete
• /
• 제6권6호
• /
• pp.505-521
• /
• 2009

The analysis of prismatic members made of reinforced concrete under inclined bending, especially the computation of ultimate loads, is a pronounced non-linear problem which is frequently solved by discretizing the stress distribution in the cross-section using interpolation functions. In the approach described in the present contribution the exact analytical stress distribution is used instead. The obtained expressions are integrated by means of a symbolic manipulation package and automatically converted to optimized Fortran code. The direct problem-computation of ultimate internal forces given the position of the neutral axis-is first described. Subsequently, two kinds of inverse problem are treated: the computation of rupture envelops and the dimensioning of reinforcement, given design internal forces. An iterative Newton-Raphson procedure is used. Examples are presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.9-11
• /
• 1999

This paper presents the problems of design and theoretical model of electrostatically driven axial-gap type wobble motor. The motor design benefits from large axial rotor-to-stator overlap and large gear ratios, and motor designs with rotor radii of 50 and $100{\mu}m$ are capable of generating torques in the [nNm] range at high electrostatic fields. Because of the large gear ratio, smaller angular steps and lower rotational speed are obtained, compared to radial-gap motor design. Aspects like gear ratio, torque generation, excitation schemes and torque coverage, normal forces, friction are addressed.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.369-374
• /
• 2007

For a stability design of steel frames, AISC-LRFD specification recommend to use Alignment Chart and story-based methods in order to determine an effective budding length. Recently, elastic buckling analysis, which is the method that calculate the effective length of members using eigenvalue of the overall structure, has been widely used in practical design of steel frames because this method can be performed effectively and automatically by computers. However, it can in some cases lead to unexpectedly large effective length in column having small axial forces. Therefore, this paper propose a method using elastic buckling analysis, which estimate a proper effective buckling length for all members having a small axial force. For verification of proposed method, it is compared with system based approach and stiffness distribution factor method. As a result, proposed method can rationally solve a problem in some case of column having small axial force. Also, adoption range for proposed method is established.

• Geomechanics and Engineering
• /
• 제21권2호
• /
• pp.111-122
• /
• 2020

In most cases in urban areas, construction of divergence tunnel should take into account proximity to existing tunnel in operation. This inevitably leads to deformation of adjacent structures and surrounding ground. Preceding researches mainly dealt with reinforcing of the diverging section for the stability including the pillar. This has limitations in investigating the interactive effects between existing structures and surrounding ground due to the excavation of the divergence tunnel. In this study, the complex interactive behavior of pile, the operating tunnel, and the surrounding ground according to horizontal offsets between the two adjacent tunnels was quantitatively analyzed based on conditions diverged from operating tunnel in urban areas. The effects on ground structures confirmed by analyzing the ground surface settlements, pile settlements, and the axial forces of the pile. The axial forces of lining in operating tunnel investigated to estimate their impact on existing tunnel. In addition, in order to identify the deformation of the surrounding ground, the close range photogrammetry applied to the laboratory model test for confirming the underground displacements. Two-dimensional finite element numerical analysis was also performed and compared with the results. It identified that the impact of excavating a divergence tunnel decreased as the horizontal offset increased. In particular, when the horizontal offset was larger than 1.0D (D is the diameter of operating tunnel), the impact on existing structures further reduced and the deformation of surrounding ground was concentrated at the top of the divergence tunnel.

• Smart Structures and Systems
• /
• 제21권5호
• /
• pp.623-635
• /
• 2018

In order to study the mechanical behavior of shield tunnel segments during assembly stage, the in-situ tests and FDM numerical simulation were conducted based on the Foguan Shiziyang Tunnel with large cross-section. Analysis for the load state of the assembling segments in different assembly steps as well as the investigation for the changing of inner forces and longitudinal stress of segments with assembling steps were carried out in this paper. By comparing the tested results with the simulated results, the conclusions and suggestions could be drawn as follows: (1) It is the most significant for the effects on axial force and bending moment caused by the assembly of adjacent segment, followed by the insertion of key segment while the effects in the other assembly steps are relative smaller. With the increasing value of axial force, the negative bending moment turns into positive and remains increasing in most monitored sections, while the bending moment of segment B1and B6 are negative and keeping increasing; (2) The closer the monitored section to the adjacent segments or the key segment, the more significant the internal forces response, and the monitored effects of key segment insertion are more obvious than that of calculation; (3) The axial forces are all in compression during assembling and the monitored values are about 1.5~1.75 times larger than the calculated values, and the monitored values of bending moment are about 2 times the numerical calculation. The bending moment is more sensitive to the segments assembly process compared with axial force, and it will result in the large bending moment of segments during assembling when the construction parameters are not suitable or the assembly error is too large. However, the internal forces in assembly stage are less than those in normal service stage; (4) The distribution of longitudinal stress has strong influence on the changing of the internal forces. The segment side surface and intrados in the middle of two adjacent jacks are the crack-sensitive positions in the early assembly stage, and subsequently segment corners far away from the jacks become the crack-sensitive parts either.