• 한국강구조학회 논문집
• /
• 제14권5호통권60호
• /
• pp.665-674
• /
• 2002

스틸 스터드 구조물에서 사용되고 있는 기존 I형, 박스형 헤더는 시공성, 경제성 측면에서 여러 가지 문제점을 노출하고 있다. 이러한 문제점을 극복하기 위해 선진국에서는 냉간성형강을 L형으로 절곡한 L-헤더를 활발히 사용하고 있다. 그러나 국내에서는 이에 대한 연구가 부족하여 L-헤더를 사용하지 못하고 있는 실정이다. 본 연구에서는 이러한 문제점을 해결하기 위해 L-헤더에 대한 좌굴해석 및 휨 실험을 수행하였으며, 실험결과를 미국 철강협회(AISI, American Iron and Steel Institute) 설계기준과 비교하였다. 휨 실험결과 중력방향 하중이 작용하는 경우에는 국부좌굴이, 인발하중이 작용하는 경우에는 뒤틀림 좌굴이 발생되는 것으로 관찰되었다. 그리고 실험에서 측정된 좌굴 하중을 비교한 결과 AISI 설계기준에 제시된 공칭하중을 상회하는 것으로 확인되었다.

• Structural Engineering and Mechanics
• /
• 제31권5호
• /
• pp.605-619
• /
• 2009

A comparative experimental study of prestressed continuous steel-concrete composite beams was carried out. Two continuous composite beams were tested, one of which was plain continuous steel-concrete composite beam, while the other was a composite beam prestressed with external tendons. Cracking behavior and the load carrying capacity of the beams were investigated experimentally. Full plasticity was developed in the mid-span section each beam, the maximum moments attained at the internal support sections however were governed by local buckling which was related to the slenderness of composite section. It was found that in hogging moment regions, the ultimate resistance of an externally prestressed composite beam would be governed by either distortional lateral buckling or local buckling, or interactive mode of these two buckling patterns. The results show that exerting prestressing on a continuous composite beam with external tendons will increase the extent of internal force and moment redistribution in the beam. The influences of local and distortional buckling on the behaviors of the composite continuous beams are discussed. The Moment redistribution and the load carrying capacity of the prestressed continuous composite beams are evaluated, and it is found that at the ultimate state, the moment redistribution in the prestrssed continuous composite beams is greater than that in non-prestressed composite beams.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.43-50
• /
• 2002

Main goal of this study is to develop MATLAB programming for exact analysis of distortional deformation of the straight box girder. For this purpose, a theory for distortional deformation theory is firstly summarized and then a BEF (Beam on Elastic Foundation) theory is presented using analogy of the corresponding variables. Finally, the governing equation of the beam-column element on elastic foundation is derived. An element stiffness matrix of the beam element is established via a generalized linear eigenvalue problem. In order to verify the efficiency and accuracy of the element using exact dynamic stiffness matrix, buckling loads for the continuous beam structures with elastic foundation and distortional deformations of box girders are calculated.

• Steel and Composite Structures
• /
• 제50권6호
• /
• pp.675-688
• /
• 2024

Cold-formed steel (CFS) is prone to buckling failure under loading. Lightweight concrete (LC) made of lightweight aggregate has light weight and excellent thermal insulation performance. However, concrete is brittle in nature which is why different materials have been used to improve this inherent behavior of concrete. The distortional buckling (DB) performance of cold-formed steel-lightweight concrete (CFS-LC) composite columns was investigated in this paper. Firstly, the compressive strength test of foam concrete (FC) and ceramsite concrete (CC) was carried out. The performance of the CFS-LC members was investigated. The test results indicated that the concrete-filled can effectively control the DB of the members. Secondly, finite element (FE) models of each test specimen were developed and validated with the experimental tests followed by extensive parametric studies using numerical analysis based on the validated FE models. The results show that the thickness of the steel and the strength of the concrete-filled were the main factors on the DB and bearing capacity of the members. Finally, the bearing capacity of the test specimens was calculated by using current codes. The results showed that the design results of the AIJ-1997 specification were closer to the experimental and FE values, while other results of specifications were conservative.

• 한국강구조학회 논문집
• /
• 제16권1호통권68호
• /
• pp.155-167
• /
• 2004

각각 집중하중과 등분포하중을 받는 단순보의 비탄성 횡-비틀림 좌굴에 대하여 연구하였다. 잔류응력을 단순형과 다항식형으로 하여 line-type 유한요소법으로 해석하였다. 잔류응력의 형태는 플랜지에서는 4차 곡선으로 웨브에서는 2차 곡선으로 가정하였다. 우리나라에서 생산되는 4종류의 I형강에 대하여 비탄성 횡-비틀림 좌굴에 대하여 해석한 후 결과를 강구조편람의 내용과 비교하였다. 해석결과로부터 강구조 편람에 의한 설계는 주보에 보조보가 있는 경우나 없는 경우 모두 전반적으로 과설계임을 알 수 있었다.

• Steel and Composite Structures
• /
• 제35권6호
• /
• pp.717-727
• /
• 2020

The homotopy perturbation method (HPM) to predict the pre- and post-buckling behaviour of simply supported steel beams with rectangular hollow section (RHS) is presented in this paper. The non-linear differential equations solved by HPM derive from a kinematics where large twist and cross-sections distortions are considered. The results (linear and non-linear paths) given by the present HPM are compared to those provided by the Newton-Raphson algorithm with arc length and by the commercial FEM code Abaqus. To investigate the effect of cross-sectional distortion of beams, some numerical examples are presented.

• 한국강구조학회 논문집
• /
• 제24권2호
• /
• pp.189-197
• /
• 2012

벽식 스틸하우스 벽체의 구조재로 적용되어 오고 있는 박판냉간성형형강 스터드의 경우 열교현상에 의한 단열상의 문제를 가지고 있기 때문에 추가적인 단열재의 사용이 요구된다. 이러한 단열 문제를 해결하기 위하여 웨브에 슬릿이 배치된 냉간성형강 단열스터드가 개발되었다. 그러나 슬릿의 배치로 인하여 단면강도 산정은 대단히 어려운 문제점이 되고 있다. 본 논문에는 단열스터드의 압축강도 및 구조적인 거동에 대한 실험 및 해석적인 연구결과를 기술하였다. 슬릿의 길이, 간격 및 배열형태를 달리하는 세 종류의 단열스터드에 대한 압축실험을 단면의 파괴 시까지 수행하였으며, 실험 및 해석결과에 근거하여 복부에 슬릿이 있는 냉간성형강 스터드에 적용하기 위한 단순한 형태의 강도 산정방법을 제안하였다. 제안된 강도산정법에서는 단열스터드를 등가두께의 슬릿이 없는 일반스터드로 대치하고, 이 등가단면에 직접강도법을 적용하여 단열스터드의 공칭압축강도를 산출한다. 제안된 강도산정방법은 단열스터드 실험결과와 비교하여 검증하였다.

• Steel and Composite Structures
• /
• 제12권1호
• /
• pp.73-92
• /
• 2012

The effect of element interaction and material nonlinearity on the ultimate capacity of stainless steel plated cross-sections is investigated in this paper. The focus of the research lies in cross-sections failing by local buckling; member instabilities, distortional buckling and interactions thereof with local buckling are not considered. The cross-sections investigated include rectangular hollow sections (RHS), I sections and parallel flange channels (PFC). Based on previous finite element investigations of structural stainless steel stub columns, parametric studies were conducted and the ultimate capacity of the aforementioned cross-sections with a range of element slendernesses and aspect ratios has been obtained. Various design methods, including the effective width approach, the direct strength method (DSM), the continuous strength method (CSM) and a design method based on regression analysis, which accounts for element interaction, were assessed on the basis of the numerical results, and the relative merits and weaknesses of each design approach have been highlighted. Element interaction has been shown to be significant for slender cross-sections, whilst the behaviour of stocky cross-sections is more strongly influenced by the material strain-hardening characteristics. A modification to the continuous strength method has been proposed to allow for the effect of element interaction, which leads to more reliable ultimate capacity predictions. Comparisons with available test data have also been made to demonstrate the enhanced accuracy of the proposed method and its suitability for the treatment of local buckling in stainless steel cross-sections.

• Steel and Composite Structures
• /
• 제6권3호
• /
• pp.221-236
• /
• 2006

The objective of this work is to describe the main steps involved in the derivation of a GBT (Generalised Beam Theory) formulation to analyse the vibration behaviour of loaded cold-formed steel members and also to illustrate the application and capabilities of this formulation. In particular, the paper presents and discusses the results of a detailed investigation about the local and global free vibration behaviour of lipped channel simply supported columns. After reporting some relevant earlier GBT-based results dealing with the buckling and vibration behaviours of columns and load-free members, the paper addresses mostly issues concerning the variation of the column fundamental frequency and vibration mode nature/shape with its length and axial compression level. For validation purposes, some GBT-based results are also compared with values obtained by means of 4-node shell finite element analyses performed in the code ABAQUS.

• 한국강구조학회 논문집
• /
• 제14권2호
• /
• pp.349-356
• /
• 2002

현재 우리나라 스틸하우스 건설에 사용하는 구조재는 SGC41 강종으로 제작된 보통 C-형강이나 Lip-C-형강이 주를 이루고 있으나 이 분야의 선진국가에서는 좌굴 강도가 높고 시공성이 좋은 고유의 단면 형상을 개발하여 사용하고 있다. 본 연구에서는 정량이면서 강도 및 강성이 높고 다양한 시공상 장점이 있는 고강도 신형상 박판냉간성형단면의 압축부재로서의 구조적인 고동과 성능을 연구하기 위하여 재료실험 및 압축실험을 수행하고 해석치와 비교하여 보았다.