• Journal of the Korean institute of surface engineering
• /
• v.51 no.6
• /
• pp.415-420
• /
• 2018

The possibility of an improvement in heat dissipation performance of aluminum alloy heat sink for shipboard LED luminaries through plasma electrolytic oxidation (PEO) was investigated. Four different PEO coatings were produced on aluminum alloy 5052 in silicate based alkaline solution by varying current density ($50{\sim}200mA/cm^2$). On voltage-time response curves, three stages were clearly distinguished at all current densities, namely an initial linear increase, slowdown of increase rate, and steady state(constant voltage). It was found that the increase in current density caused the breakdown voltage to increase. Two different surface morphologies - coralline porous structure and pancake structure - were confirmed by SEM examination. The coralline porous structure was predominant in the coatings produced at lower current densities (50 and $100mA/cm^2$) while under high current densities(150 and $200mA/cm^2$) the pancake structure became dominant. The coating thickness was measured and found to be in a range between about $13{\mu}m$ and $44{\mu}m$, showing increasing thickness with increasing current density. As a result, $100mA/cm^2$ was proposed as an effective process parameter to improve the heat dissipation performance of aluminum alloy heat sink, which could lower the LED operating temperature by about 30%.

• Earthquakes and Structures
• /
• v.23 no.5
• /
• pp.473-491
• /
• 2022

The research investigates experimentally the effect of confinement on structural behavior at the ends of beam-column in reinforced concrete (RC) frames. In the experimental study, five specimens consisting of 1/3-scaled RC frames having single-bay, representing the traditional deficiencies of existing buildings constructed without receiving proper engineering service is investigated. The RC frame specimens were produced to represent most of the existing buildings in Turkey that have damage potential. To decrease the probable damage to the existing buildings exposed to earthquakes, the carbon Textile Reinforced Mortar (TRM) strengthening technique (fully wrapping) was used on the ends of the RC frame elements to increase the energy dissipation and deformation capacity. The specimens were tested under reversed cyclic lateral loading with constant axial loads. They were constructed satisfying the weak column-strong beam condition and consisting of low-strength concrete, such as compressive strength of 15 MPa. The test results were compared and evaluated considering stiffness, strength, energy dissipation capacity, structural damping, ductility, and damage propagation in detail. Comprehensive investigations of these experimental results reveal that the strengthening of a brittle frame with fully-TRM wrapping with non-anchored was effective in increasing the stiffness, ductility, and energy dissipation capacities of RC bare frames. It was also observed that the frame-only-retrofitting with an infill wall is not enough to increase the ductility capacity. In this case, both the frame and infill wall must be retrofitted with TRM composite to increase the stiffness, lateral load carrying, ductility and energy dissipation capacities of RC frames. The presented strengthening method can be an alternative strengthening technique to enhance the seismic performance of existing or moderately damaged RC buildings.

• Journal of the Korean Ceramic Society
• /
• v.12 no.2
• /
• pp.10-14
• /
• 1975

Bodies whose compositions are in the ternary system BaCO3-TiO2-SnO2 containing from 5 to 90 mol % stannic oxide were prepared to improve the thermal characteristics of barium titanate dielectrics. Bodies having dielectric constant (K) of 2100 at 1 KHz, low negative temperature coefficients of 1500ppm up to about 9$0^{\circ}C$, Curie Temperature of 2$0^{\circ}C$, and dissipation factor of 0.2-0.4% were obtained with addition of 15 mole % stannic oxide.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.04a
• /
• pp.85-90
• /
• 1994

Three high strength reinforced concrete structural walls were tested under the combined action of a constant axial and a horizontal cycle load. The aim of the tests has been to investigate the effects of the web horizontal reinforcement on hysteretic behavior of wall. The results have helped to identify the causes of wall failure and have demonstrated the web horizontal reinforcement does not appear have a significant effect on shear capacity, stiffness and energy dissipation but have a significant effect on the failure mode of the walls.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.320-322
• /
• 1996

In this paper, solar array switching regulation is proposed as a replacement for conventional regulation techniques to reduce weight, thermal dissipation, and power system complexity for large power spacecraft. Each component model is developed which is used to explain the interaction of the solar array switching regulation and constant power type load, solar array.

• Korean Journal of Environmental Agriculture
• /
• v.39 no.1
• /
• pp.75-82
• /
• 2020

BACKGROUND: This study was carried out to establish pre-harvest residue limits (PHRLs) of indoxacarb and pymetrozine in broccoli under greenhouse conditions, based on dissipation patterns and biological half-lives of pesticides during 10 days after application. METHODS AND RESULTS: The field studies were conducted in two different greenhouse, located in Chungju-si (Field 1) and Gunsan-si (Field 2). Samples were collected at 0, 1, 2, 3, 5, 7 and 10 days after spraying pesticide suspension. The analytical methods for indoxacarb and pymetrozine using HPLC-DAD were validated by recoveries ranging of 94.3-105.4% and 81.8-96.0%, respectively, and MLOQ (Method Limit of Quantification) of 0.05 mg/kg. Biological half-lives of indoxacarb and pymetrozine were 2.9 and 3.2-3.8 days in broccoli, respectively. The lower 95% confidence intervals of dissipation rate constant of indoxacarb were determined as 0.1508 (Field 1) and 0.2017 (Field 2), whereas those of pymetrozine were calculated as 0.1489 (Field 1) and 0.1577 (Field 2). CONCLUSION: The significant differences were not observed between the dissipation rates of indoxacarb and pymetrozine in broccoli. The major factor affecting residue dissipation was the dilution effect by fast growth. The PHRLs for 10 days prior to harvest were recommended as 30.06 (Field 1) and 18.07 (Field 2) mg/kg for indoxacarb, and 4.84 (Field 1) and 4.43 (Field 2) mg/kg for pymetrozine, respectively.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.871-874
• /
• 1992

The dielectric constant and dissipation factor of polyphenylene sulfide(PPS) film were measured in range of -40$\sim$+125$^{\circ}C$. The result shows that characteristics of PPS films are superier to PP and PET films. It's dielectric constant was stable to the temperature of +125$^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.347-350
• /
• 1995

In this paper, we fabricated fuel shortage detecting sensor, utilizing NTC thermistor concerned with Mn-Ni-Co system. We would be obtained B constant value of 1930∼2080 and resistivity 387∼430(ohm-cm) additive Bi$_2$O$_3$0∼0.5 wt% to Mn$_3$O$_4$:9wt%, Co$_3$O$_4$:61wt%, NiO:28wt% under 1150∼1250$^{\circ}C$ of sintering temperature. In sensor, we obtained characteristics, which we want, in resistance range 850∼l150$\Omega$, B constant 2000${\pm}$5%. we can see 15 multiplied differences between gasoline and heat dissipation coefficient of air condition.

• Transactions of Materials Processing
• /
• v.25 no.1
• /
• pp.5-11
• /
• 2016

The control of the roll velocities is essential in maintaining stability during ring rolling, but such control is difficult. The determination of the best roll velocities can be helped with the use of FE simulations and processing maps, which give the useful information such as power dissipation and flow instability for hot metal forming processes. In the current study, the workability of 7050 aluminum alloy is evaluated by using processing map. With the developed information, the stability of the ring rolling condition, called the Constant Growth Velocity Condition (CGVC), is evaluated.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1597-1599
• /
• 1996

In this study, we investigated the electrical characteristics such as tracking resistance, dielectric constant, insulating resistance, and arc resistance, of silicone rubber for outdoor use, and, focused on the tracking resistance. In the Inclined Plane Test, two kind of the contamination solutions were used, and their phenomena were observed. The average leakage current and the tracking breakdown time decreased, and erosion rate increased, using anionic surfactant added contaminant solution. The dielectric constant and dissipation factor were increased with increasing temperature.