• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1596-1599
• /
• 2009

Mobile ODF (one drop filling) portable display such as mobile phone and application product is needed high reliability than notebook, monitor and TV. Therefore, material development in order to optimize mobile & application ODF panel is needed. Through considering mobile ODF process and design, we have developed method of material matching test by several tests which is heat stress, UV stress and ODF process condition. So we have developed a material with characteristics of high reliability for mobile ODF panel.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.2
• /
• pp.163-169
• /
• 2000

In this paper, we showed the erosion characteristic of MgO protector layer releated to lifetime of plasma display panel(PDP). We observed MgO erosion characteristic as a functions of deposition conditions, pressure and distance between electrodes. In RIE condition of Xe gas, the lowest erosion rate appears in the conditions of no heating bias voltage -30V and pressure 5mtorr. In general, as deposition rate increases, erosion rate decreases. In real panel, when the gap distance between electrodes is narrow and the pressure is low, the heavy plasma damage appears. Also, the surfaces between electrodes and on the bus electrode are extremely damaged.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.284-287
• /
• 2000

We analyzed the 3-dimensional discharge characteristic in plasma display panel(PDP) cell using the 3-dimensional emission distribution of 828nm light measured by scanned point detecting method(SPDM). The emitted light distributions on the ITO electrode show the stronger light intensity near to the electrode gap than outside. Also, 828nm light is widely detected outside of the bus electrode. We consider that measurement using new SPDM is effective to analyze the discharge physics and propose the new panel structures.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.906-909
• /
• 2012

The address discharge characteristics of a open dielectric structure compared with the conventional panel structure are investigated by measuring the discharge firing voltage. The open dielectric structure could easily produce the discharge between the scan and the sustain electrodes by erasing the dielectric layer between two electrodes. Due to the changes in the discharge firing characteristics of the open dielectric structure between the two sustain electrodes, the conventional reset waveform including the address waveform needs to be modified. The modified driving waveform suitable for the open dielectric structure is proposed and examined in AC PDP.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.3
• /
• pp.453-458
• /
• 1987

Amorphous silicon thin-film transtors (TFT's) have been designed and fabricated on glass substrates. The hydrogenated amorphous silicon (a-Si:H) thin-film has been deposited by decomposing silane(SiH4) in hydorgen ambient by rf glow discharge method. Amorphous silicon nitride(a-Si:H) has been chosen as the gate dielectric material. It has been prepared by decomposing the mixed gas of silane(SiH4) and ammonia(NH3). The electrical properties and performance characteristics of the thin-film transistrs have been measured and compared with the requirements for the switching elements in liquid crystal flat panel display. The results show that liquid crystal flat panel displays can be fabricated using the thin-film transistors described in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.302-305
• /
• 1995

ITO(indium tin oxide) that is both conductive in electricity and transparent to the visible ray is called transparent conducting thin film. Nowaday, according to the development of flat panel display such as LCD(Liquid Crystal display, EL(electolumine- scence display), PDP(plasma display panel), ECD(electrocromic display), the higher quality in the low temperature process has been asked to reduce the production cost and to have a good uniformity on a large substrate. In this study, we prepared indium tin oxide(ITO) by a cylindrical DC magnetron sputtering with Indium-tin (9:1) alloy target instead of indium-tin oxide target. To reduce the defact in ITO, the effect on ITO by varing the magnetic field intensity and the applied voltage ares studied. the resistivity of the film deposited in oxygen partial pressure of 5% and substrate temperature of 140$^{\circ}C$. is 1.6${\times}$10$\^$-1/$\Omega$$.$cm with 85% optical transmission in viaible ray.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.776-779
• /
• 2006

The alignment of liquid crystal (LC) is one of the key issues of liquid crystal display (LCD) technologies. In this study, we aligned polyimide (as the LC alignment layer) by ALT plasma beam and to realize the stability and characteristics of this technology. The characteristics such as anchoring energy, pre-tilt angle, voltage holding ratio(VHR) and residual direct current(Rdc) were discussed. Besides, we applied it to the in plane switch (IPS) mode 23" WXGA real panel, the performance parameters and electrical properties were measured and compared with those of rubbing alignment. From the result, we demonstrated a successful LC alignment treatment process in real panel by ALT plasma beam.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.24-33
• /
• 2001

The characteristics of the reset and the address discharges of an alternating current Plasma Display Panel (ac PDP) were studied using 2-dimensional numerical discharge cell simulation. We investigated the wall charge variations during the reset discharge adopting ramping reset pulse and the subsequent addressing discharge. The roles of the ramping reset scheme can be divided into two stages, each electrode gathers wall charges during ramping-up of the initial stage and the built-up wall charges are lost during ramping-down of the later stage. Address discharge does not only change the wall charge distributions on the address and the scan electrodes but also on the sustain electrode. The increase in the wall charges on the sustain electrode was observed with the variation of the applied voltage to the sustain electrode during the address period. The increase of the applied voltage to the sustain electrode during the address period is expected to induce the decrease of the sustain voltage during the display period.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1343-1351
• /
• 2012

In this study, trends for five research areas of LED(Light Emitting Diode), OLED(Organic Light Emitting Diode), LCD(Liquid Crystal Display), PDP(Plasma Display Panel) and CRT(Cathode Ray Tube) are investigated using bibliometric analysis. The papers and patents citation data were extracted from Scopus and USPTO databases, respectively. We could figure out the research trends by the number of publications and citation information. We prospect the current interests and future trends by investigating the development process of the 5 research areas as function of time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.534-538
• /
• 2013

We propose a generic method to calculate the optical functionalities of a 3D display with a lenticular lens array. In the present work, based on the geometrical optics, it is designed considering the specifications of the display panel. For the effective simulation, we first calculate the optical functionalities of a single cylindrical lens and, by comparing with the results obtained from the conventional geometrical optics, confirm the validity of the present method. Afterwards, we obtain the full distribution of the light intensity at an optimum viewing distance by expanding the results of the single lens to the horizontal plane of the display panel. From these results, we finally confirm whether the 3D images are realized or not in the system.