• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.65-68
• /
• 2010

The operation principle of a traveling wave rotary type ultrasonic motor can be successfully applied to the fluidic transfer mechanism of the micro-pump. This paper proposes an innovative valveless micro-pump type that uses an extensional vibration mode of a traveling wave as a volume transportation means. The proposed pump consists of coaxial cylindrical shells that join the piezoelectric ceramic ring and metal body, respectively. In order to confirm the actuation mechanism of the proposed pump model, a numerical simulation analysis was implemented. In accordance with the variations in the exciting wave mode and pump body dimension, we analyzed the vibration displacement characteristics of the proposed model, determined the optimal design condition, fabricated the prototype pump from the analysis results and evaluated its performance. The maximum flow rate was approximately $595\;{\mu}L/min$ and the highest back pressure was 0.88 kPa at an input voltage of $130\;V_{rms}$. We confirmed that the peristaltic motion of the piezoelectric actuator was effectively applied to the fluid transfer mechanism of the valveless type micro pump throughout this research.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.1
• /
• pp.53-60
• /
• 2018

The ICT concept has been introduced to realize a highly productive smart factory and respond to the demand for small quantity and mass production between textile processes. ICT convergence monitoring system that can produce high productivity textile products by improving product development period, cost, quality and delivery time through ICT based production and optimization of manufacturing process is needed. In this paper, we propose and implement a system design that senses the amount of remaining sewing material using a non-contact sensor that can be mounted on a sewing machine and displays it on a display using IOT-based LATTE-PANDA board.

• Geomechanics and Engineering
• /
• v.10 no.2
• /
• pp.207-224
• /
• 2016

Granulated coal ash (GCA), a mixture of the by-product from milling processes with a small amount of cement added, has recently come to be used as a new form of geomaterial. The shear strength and deformation behaviours of GCA are greatly determined by its relative density or void ratio. A series of drained triaxial compression tests were performed on cylindrical specimens of GCA at confining pressures of between 50 kPa and 400 kPa at initial relative densities of 50%, 70% and 80%. Experimental results show that a rise in relative density increases the peak shear strength and intensifies the dilation behaviour. The initial tangent modulus and secant modulus of the stress-strain curve increase with increasing initial relative density, whereas the axial and volumetric strains at failure decrease with level of initial relative density. The stress-dilatancy relationships of GCA at different relative densities and confining pressures display similar tendency. The dilatancy behaviour of GCA is modelled by the Nova rule and the material property N in Nova rule of GCA is much larger than that of natural sand.

• 보존과학연구
• /
• s.27
• /
• pp.23-42
• /
• 2006

This study is about gilt bronze ornament, that is from Deok Cheon-Ri in Gyeong Ju, of conservation treatment process and of scientific analysis. This relic gathered with soil around the relic by Polyurethane foam. While the relic got rid of soil, Took X-rays. As the result, we decided to process reconstruction as condition that the relic was dug up. After the conservation treatment processed, we made a frame to display the relic. Investigated manufacture techniques of the relic after the conservation treatment processed, and thenexecuted scientific analysis of the relic for a chemical experiment. A analysis of the results of components for composition layers using the SEM-EDS can be briefly summarized as below; Firstly, the average contents of outer, inner and body corrosion layer have a Cu-60.9~39.3wt% and analyzed a little impurities material which is Fe-0.5wt%.Secondly, the average contents of body have a Cu-99.7wt% which was using manufactured by pure copper. Thirdly, gold layer have a mercury of 9.5wt% which indicate that layer was manufactured by mercury amalgam gilding technique.

• Journal of the Korean Ceramic Society
• /
• v.52 no.3
• /
• pp.224-227
• /
• 2015

In this work, the properties of Indium-Zinc-Tin-Oxide (IZTO) thin films, deposited on polyethylene naphthalate (PEN) with a $SiO_2$ buffer layer, were analyzed with different working pressures. After depositing the $SiO_2$ buffer layer on PEN substrates by plasma-enhanced chemical vapor deposition (PECVD), the IZTO thin films were deposited by RF magnetron sputtering with 1 to 7-mTorr working pressure. All the IZTO thin films show an amorphous structure, regardless of the working pressure. The best morphological, electrical, and optical properties are obtained at 3-mTorr working pressure, with a surface roughness of 2.112-nm, a sheet resistance of $8.87-{\Omega}/sq$, and a transmittance at 550-nm of 88.44%. These results indicate that IZTO thin films deposited on PEN have outstanding electrical and optical properties, and the PEN plastic substrate is a suitable material for display devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.389-392
• /
• 2009

Metal oxides have been proposed as an alternative channel material to hydrogenated amorphous silicon in thin film transistors (TFTs) because their higher mobility and stability make them suitable for transistor active layers. Thin films of indium zinc oxide (IZO) were deposited using a High Target Utilization Sputtering (HiTUS) system on various dielectrics, some of which were also deposited with the HiTUS. Investigations into bottom-gated IZO TFTs have found mobilities of 8 $cm^2V\;^1s^{-1}$ and switching ratios of $10^6$. There is a variation in the threshold voltage dependent on both oxygen concentration, and dielectric choice. Silica, alumina and silicon nitride produced stable TFTs, whilst hafnia was found to break down as a result of the IZO.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.3
• /
• pp.89-92
• /
• 2009

High-quality Al-N doped p-type ZnO thin films were deposited on Si and buffer layer/Si by DC magnetron sputtering in a mixture of $N_2$ and $O_2$ gas. The target was ceramic ZnO mixed with $Al_2O_3$ (2 wt%). The p-type ZnO thin films showed a carrier concentration in the range of $1.5{\times}10^{15}{\sim}2.93{\times}10^{17}\;cm^{-3}$, resistivity in the range of 131.2${\sim}$2.864 ${\Omega}cm$, mobility in the range of 3.99${\sim}$31.6 $cm^2V^{-1}s^{-l}$, respectively. It was easier to dope p-type ZnO films on Si substrates than on buffer layer/Si. The film grown on Si showed the highest quality of photoluminescence (PL) characteristics. The Al donor energy level depth $(E_d)$ of Al-N codoped ZnO films was reduced to about 50 meV, and the N acceptor energy level depth $(E_a)$ was reduced to 63 meV.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.4
• /
• pp.166-169
• /
• 2007

In applying LCD to TV application, one of the most significant factors to be improved is image sticking on the moving picture. LCD is different from CRT in the sense that it's continuous passive device, which holds images in entire frame period, while impulse type device generate image in very short time. To reduce image sticking problem related to hold type display mode, we made an experiment to drive TN-LCD like CRT. We made articulate images by turn on-off backlight, and we realized the ratio of Back Light on-off time by counting between on time and off time for video signal input during 1 frame (16.7 ms). Conventional CCFL (cold cathode fluorescent lamp) cannot follow fast on-off speed, so we evaluated new fluorescent substances of light source to improve residual light characteristic of CCFL. We realized articulate image generation similar to CRT by CCFL blinking drive and TN-LCD overdriving. As a result, reduced image sticking phenomenon was validated by naked eye and response time measurement.

• Korean Journal of Materials Research
• /
• v.18 no.3
• /
• pp.137-142
• /
• 2008

Blue-emitting BAM:Eu phosphor powders were formed by post-treatment of precursor powders with hollow or dense morphologies. The morphologies of the precursor powders obtained by spray pyrolysis were controlled by changing the preparation conditions and by changing the type of spray solution. The effects of the morphologies of the precursor powders on the characteristics of the BAM : Eu phosphor powders reacted with $AlF_3$ flux were investigated. Precursor powders with a spherical shape and a hollow morphology produced BAM : Eu phosphor powders with a plate-like morphology, a fine size and a narrow size distribution. On the other hand, precursor powders with a spherical shape and dense morphology produced BAM : Eu phosphor powders with a plate-like morphology and a large size. $AlF_3$ flux improved the photoluminescence intensities of the BAM : Eu phosphor powders. The photoluminescence intensity of the fine-sized BAM : Eu phosphor powders with a plate-like morphology was 90% of the commercial product under vacuum ultraviolet conditions.

• Journal of Fashion Business
• /
• v.15 no.6
• /
• pp.40-55
• /
• 2011

The purpose of this research is to review testing principle, testing design and experimental results of the four dynamic moisture movement testers. The research analyzes Moisture Manager Tester (MMT), Alambeta Instrument, Dynamic Surface Moisture Movement Tester, and Gravimetric Absorbent Testing Method based on American Society for Testing and Material (ASTM) E 96 which is an international standard testing method. Although many of researches use ASTM E 96 to measure moisture movement on a fabric, it has several weaknesses, such as long experimental time and a physical change of sample by a holder of the frame. Hence, lots of researchers have studied and developed the new measurement systems measuring moisture management on a fabric or garment and ultimately mimic heat energy and perspiration created by the human body. These moisture management systems use a variety of parameters, such as electricity, color, and sensor to measure their movement in the fabric. Through comparison with the existing tester (ASTM E 96), the research recognizes the strength and weakness in the dynamic moisture movement testers.