• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.363-368
• /
• 2002

A practical implementation method of squeeze-film aeroelastic disk vibration damping and its practical design performance are presented to provide a solution method to meet the tight TMR(Track Mis-Registration) design budget of high-TPI HDDs. Most previous research results are mainly based on the component-level study in the 'open-cover state' which is far from the realistic operation HDD condition. In this study, the squeeze-film disk damping effect is widely investigated under the realistic drive-level condition of 'enclosed-cover state.' It is found that the proper aeroelastic gap(s) between disk(s) and adjacent surface(s) to give significant vibration reduction in the enclosed HDD operating conditions can be achieved not only by classical well-known squeeze-film damping gaps such as very small 0.0x-millimeter level gaps which are not practically implementable in mass-production HDDs, but also by a few 0.x millimeter which is possible for designing realistic HDD design. The various experimental results including drive-level PES are also presented to prove feasibility of the optimal disk damper design for 93kTPI HDDs.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.2
• /
• pp.101-105
• /
• 2006

Disk radial runout creates a periodic relative motion between the laser beam spot and tracks formed on an optical disk. While only focus control is activated, the periodic relative motion yields sinusoid-like waves in the tracking error signal, where one cycle of the sinusoid-like waves corresponds to one track. The frequency of the sinusoid-like waves varies depending on the disk rotational speed and the amount of the disk radial runout. If the frequency of the tracking error signal in the off-track state is too high due to large radial runout of the disk, it is not a simple matter to begin track-following control stably. It might take a long time to reach a steady state or tracking control might fail to reach a stable steady state in the worst case. This article proposes a simple method for reducing the relative motion caused by the disk radial runout in the off-track state. The relative motion in the off-track state is effectively reduced by a drive input obtained through measurements of the tracking error signal and simple calculations based on the measurements, which helps reduce the transient response time of the track-following control. The validity of the proposed method is verified through an experiment using an optical disk drive.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.10 no.1
• /
• pp.95-105
• /
• 2006

The speed of hard disk which is based on mechanical operation is more slow than processor. The growth of processor speed is rapid by semiconductor technology, but the growth of disk speed which is based on mechanical operation is not enough. Buffer cache in main memory and disk cache in disk controller have been used in computer system to solve the speed gap between processor and I/O subsystem. In this paper, an efficient buffer cache and disk cache management scheme was proposed to restrict duplicated disk block between buffer cache and disk cache. The performance of the proposed algorithm was evaluated by simulation.

• Korean Journal of Veterinary Service
• /
• v.22 no.1
• /
• pp.93-101
• /
• 1999

This test process on screening method for the detection of residual antibiotics in milk is simple, economic, sensitive to residual antibiotics and was given approval international organs. Thus, this study was carried out the comparison of Disk assay method and TTC-II method for sensitivity and minimum detectable range of antibiotics in raw milk. The results of this study was summarized as follows ; 1. The number of samples requested for treatment of mastitis was 198 samples. Comparison or analytical results among the methods of TTC-II, disk assay and Delve sp was that TTC-II 37 samples(18.6% ), Disk assay 125samples(63.1%), Delve SP 130 samples(65.7% ) reacted positively. Conformity rate of Delve SP and Disk assay was 70%. 2. Detectable limits of disk assay method in some antibiotics were more sensitive than those of official method(0.05-0.0025ppm in the $\beta$-lactams, 1ppm in two aminoglycoside, 0.2 ppm in one tetracycline, similar in one macrolide) 3. For sensitivity of residual sulfonamides TTC-II was much more sensitive than disk assay. Detectable limits of sulfamethazine and sulfadimethoxine were 30 to 50ppm levels. 4. The best medium preservation period is 1-2 days. 5. Concentration of brome cresol purple related to resistance for B stearothermophilus culture was 24ppm/ml. These results show that disk assay method for screening detection of antibiotics residuces in milk is worthy of use.

• Journal of The Korean Astronomical Society
• /
• v.40 no.1
• /
• pp.9-16
• /
• 2007

We examine the morphology and luminosity distribution of a strongly warped spiral galaxy PGC 20348 by conducting a detailed BVI CCD surface photometry using BOAO 1.8m telescope. The radial surface brightness shows a break at warp radius $(r_{\omega})$ with a shallow gradient in the inner disk and a steeper gradient in the outer disk. The luminosity of east side of the disk is ${\sim}0.5$ mag fainter than the west side at r > $r_{\omega}$. The reason for the asymmetric luminosity distribution is thought to be the asymmetric flarings that result in the formation of a large diffuse region at the edge of the east disk and a smaller diffuse region at the west disk. The vertical luminosity profiles show a thick disk component whose scale heights increase with increasing galactocentric distances. The warp of PGC 20348 seems to be made by the tidal interactions with the two massive companion galaxies since the flarings and radial increase of disk scale heights are thought to be general properties of tidally perturbed disks. According to the colors of the two clumps inside the diffuse region at the edge of the east disk, they seem to be sites of active star formation triggered by tidal forces from the companion galaxies.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1703-1708
• /
• 2004

In this study, we are investigated experimentally the pumping characteristics about the pumping channel shapes of disk-type drag pump (DTDP). We are experimented the pumping performance about the rotors which have channel or do not exist. The channel disk-type rotor has spiral channels both upper and lower part, and stator is planar. The planar disk-type rotor hasn't channel and stator has spiral channels both upper and lower part. The flow-meter method is adopted to calculate the pumping speed. Compression ratio and pumping speeds for the nitrogen gas are measured under the inlet pressure range of 0.001 ${\sim}$ 4 Torr. The maximum of compression ratio was about 3300 for three-stage DTDP (channel disk-type rotor), 1000 for four-stage (planar disk-type rotor) and two-stage DTDP (channel disk-type rotor) at zero throughput. The ultimate pressure was $1.6{\times}10^{-6}$ Torr for three-stage DTDP (channel disk-type rotor), $2.5{\times}10^{-6}$ Torr for four-stage DTDP (planar disk-type rotor).

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.5
• /
• pp.1470-1477
• /
• 2016

This study has designed and evaluated the safety of watertight damper for Offshore Rigs. The watertight damper is an improved design for conventional DN 350 butterfly valve. Numerical analysis has been performed to investigate the safety factor and seat leakage of the designed 3-type disk dampers. The structure analysis results present the deformations, the equivalent stresses and the safety factor. It was confirmed that the designed disk, rib-disk and streamlined disk of watertight damper are safe enough in maximum operating pressure of 0.98MPa. The results show that the disk damper had the smallest maximum deformations and stress among 3-type disk dampers and the safety factor was 4.3. Therefore it is confirmed that the disk damper has the most excellent strength. Also linear static structural analysis was individually conducted for disk and body. The results show that the maximum disk deformation was larger than the body deformation, Therefore the disk damper is causes no seat leakage.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.167-174
• /
• 1998

In this work the surface damage of head and disk of a hard disk drive was analysed using an Atomic Force Microscope. The initial damage of the disk occurred by generation of extremely small wear particles. Also it was shown that wear particles tend to pile up near the front side of the slider. The surface damage mechanism of drag test and contact-start-stop test was found to be quite similar.

• Bulletin of the Korean Mathematical Society
• /
• v.36 no.2
• /
• pp.395-402
• /
• 1999

We introduce the notion of strongly k-disk homogeneous apace and establish a characterization theorem. More specifically, we prove that any analytic Riemannian manifold (M,g) of dimension n which is strongly k-disk homogeneous with 2$\leq$k$\leq$n-1 is a space of constant curvature. Its K hler analog is obtained. The total mean curvature homogeneity of geodesic sphere in k-disk is also considered.

• Tribology and Lubricants
• /
• v.16 no.6
• /
• pp.415-424
• /
• 2000

The use of magnetoresistive (MR) head requires much tighter control of particle contamination in a drive since loose particles on the disk surface will generate thermal asperities (TA). In this study, a spinoff test was performed to investigate the adhesion and removal capability of a particle to disk surface. Numerical simulation was also performed to investigate dominant factor of particle detachment and to support experimental results. It was shown that particles are detached from the disk surface by the moment derived from the centrifugal force and the drag force and that the centrifugal force and capillary force are the dominant force, which determines spin-off of a particle on the disk surface. Removal of particles smaller than several micrometers, which are the main source of TA generation, is extremely difficult since the adhesion forces exceed the centrifugal force. Lubricant types and manufacturing process also influence the particle removal. Lower bonding ratio and lower viscosity of the lubricant will help to increase the removal rate of the particles from the disk surface.